Mitel Sx-100, Sx-200 Attendant Console Guide

							VOLUME/TONE RINGER 
1 
l To adjust the volume of the tone 4 0 To turn the ringer ON, press BELL 
ringer, use the control on the back 
OFF key again 
of the console 
0 BELL OFF lamp goes out; the tone 
ringer is now reconnected 
2 OTo turn the ringer OFF, press BELL 
OFF key 
3 l BELL OFF lamp lights; the tone 
ringer is now disconnected 
B39 . 
‘.I :: 
_._.‘.. 
:L:;‘. 
,_-.. :. 
.^_F._. 
..--.--, _.. 
.: : .,: : - 
:  
						

							HOTEL FEATURES  
						

							AUTOMATIC WAKE-UP (SETTING) 
To set or change: 
I 0 Press GUEST ROOM key 
0 Dial extension number (not 
required if connected to extension) 
0 GUEST ROOM lamp lights 
2 Source display shows: 
0 Number dialed 
0 Message register 
0 ATT lamp lit 
3 Destination display shows: 
0 Room status code 
0 Wake-up time if set 
4 0 Dial >k, wake-up time, then # 
(or >I< if IP-hour clock for PM) 
5 Destination display shows: 
0 Room status code 
0 Wake-up time (P if PM) 
6 0 Press RELEASE key 
0 Destination display clears 
NOTE: If a printer is used, a record is 
printed when the RELEASE key is 
pressed. 
NOTE: If more than 10 wake-up calls 
are ringing at the same time or if there 
are only four free speech paths on the 
system, subsequent wake-up calls will 
be delayed until lines become available. 
To record: 
To define which recording group an 
automatic wake-up will be routed to - 
0 Dial *234, recording group access 
code 
To delete an automatic wake-up 
recording - 
0 Dial *234#  
						

							AUTOMATIC WAKE-UP 
(CANCELING) 
To cancel: 
1 a Press GUEST ROOM key 3 Destination display shows: 
0 Present wake-up time (P if PM 
0 Dial extension number (not 0 Room status code 
required if connected to extension) 
1 
0 GU’EST ROOM lamp lights - 
4 0 Press * # (or **) 
0 Wake-up time display clears 
: 
2 Source display shows: 
0 Extension number 
0 Message register displayed 
5 0 Press RELEASE key 
0 All displays clear 
NOTE: If a printer is used a record is 
printed when the RELEASE key is 
pressed.  
						

							r-7 CAL’ El  mb AOCKINGI 
 - 
ROOW’6ROOM RESTRICTION : 
Calls between guest rooms can be 
prevented by using the call blocking To remove call blocKuW 2 0 Press CALL BLOCK key 
l CALL BLOCK lamp goes out 
feature* 
‘ta set up call blocking: 
_ 
m_ - 
I 
0 Press CALL BLOCK Key 
l CALL BLOCK lamp lights  
						

							DO NOT DIWURB 
(SET UP/DISPLAY) 
To set up Do Not Disturb: 
1 @Press GUEST ROOM key 
OGUEST ROOM lamp lights 
0 Dial extension number 
2 Source display shows: 
0 Extension number 
0 Message register 
l ATT lamp lit 
3 0 Press DO NOT DSTB key 
0 DO NOT DSTB lamp lights 
0 Busy lamp field shows extension 
busy 
4 0 Press RELEASE key 
0 All displays clear 
@ Busy lamp field shows extension 
busy 
Automatic Wake-up will override Do Not 
Disturb. To display which guest rooms have Do 
Not Disturb applied: 
1 0 Press and hold down DO NOT DSTB 
key 
0 Busy lamp field shows the 
extensions that have Do Not Disturb 
applied 
2 Source display shows: 
@Number of rooms with do Not 
Disturb set  
						

							DO NOT DISTURB [CANCEL) 
ho cancel Do Not Disturb: 
1 0 Press GUEST ROOM key 
e Dial extension number 
0 GUEST ROOM lamp lights 
0 DO NOT DSTB lamp lights 
2 
Source display shows: 
0 Number dialed 
0 Message Register 
0 ATT lamp lit 
3 
0 Press DO NOT DSTB key 
0 DO NOT DSTB lamp goes out 
3 
0 Press RELEASE key 
0 Source display clears  
						

							MESSAGE REGISTER 
To request a print of room call counts: 
1 @Dial >t
						

							,MESSAGE REGISTER 
OF AN EXTENSION 
1 0 Press GUEST ROOM key 
0 GUEST ROOM lamp lights 
0 Dial extension number 
l ATT lamp lit 
2 Source display shows: 
0 Extension number 
l The number of local call units made 
from the room. The display can 
show a value of up to 9999. After 
this, decimal points are lit in 
sequence starting from the right of 
the display, to indicate an 
increment of 10,000; e.g., a display 
of 43.2.8. denotes a value of 34328 
3 Destination display shows: 
0 Room status code followed by “d” 
(console) or $ (printout) if “Deposit 
Paid” or >k if room is not ready 
4 0 Press # key 
5 Source display shows: 
0 Extension number and 000 
6 0 Press RELEASE key 
0 Destination and Source displays 
clear 
l AII lamps go out 
NOTE: If a printer is used the contents 
of the message register are printed 
before it is reset.  
						

							MESSAGE WAITING (SET UP) 
Using the GUEST ROOM key: 
1 0 Press GUEST ROOM key 
0 GUEST ROOM lamp lights 
0 Dial extension number 
2 Source display shows: 
0 Number dialed 
l ATT lamp lit 
0 Message Register 
3 Destination display shows: 
0 If MSGE WAIT lamp is lit, extension 
has a message waiting OR 
0 If MSGE WAIT lamp is out, press 
MSGE WAIT key 
0 MSGE WAIT lamp lit 
4 At extension: 
0 Extension message waiting lamp 
flashes or extension rings every 20 
minutes 
5 0 Press RELEASE key 
0 All displays clear Not using the GUEST ROOM key: 
You are connected to a Source or 
Destination - 
1 Source or Destination display 
shows: 
0 Extension number 
0 Class of service 
@ATT lamp lit 
2 0 Press MSGE WAIT key if MSGE 
WAIT lamp is not lit 
0 MSGE WAIT lamp lit 
3 a Press RELEASE key 
l AII displays clear 
NOTE: If a printer is used, a record is 
printed.