Oce ColorWave 600 User Manual

Illustration
Action Place the cover of the 'Connec-
tion 
panel'. 4
Chapter 3
 - Prepare the printing system for use and get started 51How to connect the network cable
Downloaded From ManualsPrinter.com Manuals 

How to connect the mains supply cable
#
Illustration
Action Plug in the 'Power' cable at the
power connection on the 'Con-
nection 

panel' at the back of the
printer.
Put the other side of the 'Power'
cable 
into the socket.
Note:
Make sure the main
power switch
 is in 'off'
position. 1
Chapter 3
 - Prepare the printing system for use and get started52How to connect the mains supply cable
Downloaded From ManualsPrinter.com Manuals 

How to switch on the printer
#
Illustration
Action Switch on the green main switch
at the rear side of the Océ Color-
Wave 600.
1
'On / Off switch' [19]Switch on the Océ ColorWave
600
 at the front side of the
printer. 2
Chapter 3
 - Prepare the printing system for use and get started 53How to switch on the printer
Downloaded From ManualsPrinter.com Manuals
19   

The installation procedure
Introduction
To install the printer and integrate the Océ ColorWave 600 system in your company
network 
you must follow four main steps.
• Run
 the installation wizard from the printer operator panel.
If you

 connect the network cable 
of your company network and you switch on your
Océ 
ColorWave 600 for the first time, an installation wizard starts automatically.
• Complete 
the printer configuration in the Océ Express WebTools (from a workstation).
• Configure the regional...

Run the installation wizard from the printer operator panel
Introduction
If you integrate the printer according to a network policy, please contact your network
administrator to get information about the network infrastructure 
and parameters.
As
 a network administrator, please refer to the Océ TDS/TCS Connectivity Manual
(available 
on CD delivered with your system) to get information about the different net-
work 
infrastructures and configurations. Before you begin
Note:
You can change the position...

How to run the installation wizard
#
Illustration
Action If you connect the network cable to your company
network and you switch on your Océ ColorWave 600
for the first time, an installation wizard starts automat-
ically.
Use 
the 'Upper right softkey' to go to the next step.
1 Use the 'Scroll wheel' to select the correct language for
your 
printer user interface.
Use 
the 'Upper right softkey' to go to the next step.
2 Use the 'Scroll wheel' to confirm your language...

Illustration
Action Use the 'Numeric keys' again to enter the serial number
of the printer for verification purpose.
Use the 'Upper right softkey' to go to the next step.
5 The printer operator panel displays the number of rolls
detected.
Use 
the 'Upper right softkey' to go to the next step.
6 Use the 'Scroll wheel' to select 'Yes' when asked if you
want 
to configure the network settings now.
Use 
the 'Upper right softkey' to go to the next step.
7 When...

Illustration
Action The following message is displayed:
'This 
wizard assists you to connect the printer to the
network'.
Use
 
the 'Upper right softkey' to go to the next step.
9 Select one of the following options.
• 'Auto detect

 (IPv4 only)'
Use

 
the 'Scroll wheel' to select 'Auto detect (IPv4
only)' 
if the system must automatically detect your
network 
settings. Confirm your entry with the
'Confirmation
 
key' above the 'Scroll wheel'.
Use...

Illustration
Action The printer operator panel now displays the network
settings.
Record 
the IP address (for example, 134.188.26.173).
You need this IP address to access 
the 'Océ Express
WebTools'
 later in order to complete the printer con-
figuration.
Use the 'Upper right softkey' to finish the network in-
stallation 
procedure and to continue with the printer
installation.
12 The 
following message is displayed:
'Insert the
 toner cartridges'
Follow 

the steps as indicated...

Illustration
Action The printer will do the calibration automatically. You
do not need to keep this printed calibration chart.
Note:
The calibration will take a several minutes.
The 
printed output is lead through the slot
below the
 'Top back cover' ('External output
(back)'). 16
The 
following message in the 'Home' screen is dis-
played:
'Ready 
to print'.
17
Continue with the following procedure:
‘Complete the printer

 configuration in the Océ Express
WebTools’  
on...