OKI C610n User Manual

41 – C610/C711 User’s Guide
Print 
Setup
(cont.)
To n e r  S a v e 
Mode
On/OffThis function works effectively 
only if the data input is color RGB 
data. This setting is valid in PS 
and PCL, but does not take effect 
in the following cases.
(1) PS: If Color Matching is set 
OFF.
(2) PS: If any setting other than 
ASIC Color Matching is set.
(3) PS: CMYK data when Ink 
Simulation Mode is used (valid in 
any other cases except Case (1) 
and Case (2) above as long as 
data is RGB).
(4) PCL binary data...

42 – C610/C711 User’s Guide
Print 
Setup
(cont.)
Edit SizeCassette Size/
A4/A5/A6/B5/
Legal14/
Legal13.5/
Legal13/Letter/
Executive/
Custom/Com-9 
Envelope/Com-
10 Envelope/
Monarch 
Envelope/DL 
Envelope/C5/
Index Card
Sets the size of an area to draw 
when the host PC does not 
specify the size via the paper 
edit size designating command 
(Not valid for PS — only for PCL).
TrappingOff
Narrow
Wide
Sets trapping.
X 
Dimension64 mm
~
210 mm
~
216 mm
Specifies paper width of Custom 
paper as a default...

43 – C610/C711 User’s Guide
PS Setup
(cont.)
USB 
Protocol
ASCII/RAWSpecifies PS communication 
protocol mode of data from USB 
port.
(In RAW mode, Ctrl-T is invalid). 
PS models only.
PCL SetupFont SourceResidentSpecifies the location of PCL 
default font.
Font 
NumberI0 ~ I90Sets the PCL font number.
The valid range of this variable 
changes depending on the FONT 
SOURCE setting at the time. If 
the default font is set for FONT 
SOURCE, the number starts at 0. 
If it is not, the number starts at 
1....

44 – C610/C711 User’s Guide
PCL Setup
(cont.)
A4 Print 
Width78 column
80 column
Sets the number of characters 
for A4 paper.
Auto LF.
This is for 10-CPI characters 
when Auto CR/LF Mode is set to 
OFF.
This menu is enabled only when 
A4 paper is selected in the menu 
that sets the print width of A4 
paper in portrait orientation.
Usually, such A4 paper print 
width is set slightly narrower 
than 8 inches (about 7.93 
inches).
This setting cannot print 80 10-
cpi characters (only prints up to 
78 10-cpi...

45 – C610/C711 User’s Guide
PCL Setup
(cont.)
White Page 
SkipOn/OffSets whether to eject a page 
without any data to print (blank 
page) upon reception of FF 
command (OCH) in PCL Mode.
OFF: Ejecting.
CR FunctionCR/CR+LFSets action when CR code is 
received in PCL.
CR: Carriage Return 
CR+LF: Carriage Return and Line 
Feed
LF FunctionLF/ LF+CRSets action when LF code is 
received in PCL.
LF: Line Feed 
LF+CR: Line Feed and Carriage 
Return
Print MarginNormal
1/5 inch
1/6 inch
Sets a non-printable area...

46 – C610/C711 User’s Guide
PCL Setup 
(cont.)
Pen Width 
Adjust
On/OffWhen minimum width is 
specified in PCL, sometimes a 1-
dot line, looks broken.
With PEN WIDTH Adjust set to 
ON, when the minimum width is 
specified, the line width will be 
emphasized so as to look wider 
than a 1-dot line.
With PEN WIDTH Adjust set to 
OFF, the line will appear as 
before.
Tr a y  I D  #
Tr a y  2  1 ~  5 ~ 59Sets the # to specify Tray 2 for 
the paper feed destination 
command (ESC&l#H) in PCL5e 
emulation....

47 – C610/C711 User’s Guide
IBM PPR 
Setup
(cont.)
Symbol SetIBM 437Sets the Symbol Set for IBM PPR 
(see machine operator panel for 
complete list).
Letter O 
StyleEnable/DisableSpecifies the style that replaces 
ø (9B) and ¥ (9D) with ø (ou) 
and Ø (zero).
Zero 
CharacterNormal /
SlashedSpecifies the style of 0(zero). 
SLASHED: SLASH ZERO
Line Pitch6 /8 LPISets line space.
White Page 
SkipOn/ OffSets whether to eject a blank 
sheet. Available only when 
simplex is set.
CR FunctionCR/CR+LFSets action...

48 – C610/C711 User’s Guide
EPSON FX 
SetupCharacter 
Pitch10 CPI/12 CPI/
17 CPI
20 CPI/
Proportional
Specifies character pitch in 
Epson FX emulation.
Character 
SetSET-2
SET-1
Sets a character set.
Symbol SetIBM 437Sets the Symbol Set for Epson 
FX Emulation.
(see machine operator panel for 
complete list).
Letter O 
StyleEnable/ DisableSpecifies the style that replaces 
ø (9B) and ¥ (9D) with ø (ou) 
and Ø (zero).
Zero 
CharacterNormal /
SlashedSpecifies the style of 0(zero). 
SLASHED: SLASH ZERO...

49 – C610/C711 User’s Guide
Color 
SetupInk 
Simulation
Off
SWOP
Euroscale
Japan
The machine has its own process 
simulation engine which 
simulates standard colors in the 
printer.
This function is available only 
with PS language jobs.
UCRLow
Medium
High
Selects limitation to the toner 
layer thickness.
If paper curl occurs in dark 
printing, selecting MEDIUM or 
LIGHT sometimes helps reduce 
this curl.
UCR = Under Color Removal.
CMY 100%
Density
Enable/DisableEnable/Disable 100% output 
against the...

50 – C610/C711 User’s Guide
Memory 
SetupReceive 
Buffer Size
Auto
0.5 megabyte
1 megabyte
2 megabyte
4 megabyte
8 megabyte
16 megabyte
32 megabyte
Sets the size of receive buffer
Resource 
Save
Auto
Off
0.5 megabyte
1 megabyte
2 megabyte
4 megabyte
8 megabyte
16 megabyte
32 megabyte
Sets the size of resource saving 
area.
Flash 
Memory 
SetupInitializeExecuteInitializes Resident FLASH.
When the Enter button is 
pressed, the following 
confirmation message appears.
  Are You Sure?          Yes/No
If  No...