Panasonic Digital Imaging System DP-3510/4510/6010 Copier & Network Scanner Operating Instructions

							11

The copier should not be installed in areas with the
following conditions:
CExtremely high or low temperature and humidity.
Ambient conditions Temperature: 10 – 30°C
Relative humidity: 30 – 80 %
CWhere temperature and humidity can change
rapidly, causing condensation.
CDirect exposure to sunlight.
CDirectly in the air conditioning flow.
CIn areas of high dust concentration.
CIn areas of poor ventilation.
CIn areas with chemical fume concentration.
CIn areas with extreme vibration.
CWith unstable or uneven conditions (floors, etc.).
InstallationPrecautions
Before Starting
FOR YOUR  SAFETY

The maximum power consumption is 1.45 kW.
A properly wired (grounded), dedicated, 6.5A, 220-240V AC outlet is required. Do not use an
extension cord.
Caution Note: Disconnect from the mains supply before removing covers.
CTHIS PRODUCT CONTAINS A LITHIUM BATTERY. DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS OF YOUR LOCAL SOLID WASTE OFFICIALS.
CAUTION
P010-011_4510(pb).p657/31/02, 10:44 AM 11 
						

							12
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13
amps and that it is approved by ASTA or BSI to BS1362
Check for the ASTA mark 7 or the BSI mark 6 on the body of the fuse.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is
replaced.
If you lose the fuse cover the plug must not be used until a replacement cover is obtained.
A replacement fuse cover can be purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR OFFICE
THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMP SOCKET.
If a new plug is to be fitted please observe the wiring code as shown below.
If in any doubt please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green and Yellow: Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the main lead of this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which
is marked by letter E or by the safety Earth symbol “L” or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked
with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in
the plug which is marked with the letter L or coloured RED.
How to replace the fuse.
Open the fuse compartment with a screwdriver and replace the fuse.
For U.K.
N
Precautions
Installation
P012-013_4510(pb).p657/31/02, 10:44 AM 12 
						

							13
B4·FLS
ORIGINAL
SIZE KeysCOPY SIZE
KeysTouch Panel
DisplayKeypad START
Key
No. Contents
#COPY Key
CPress when using the unit as a photocopier.
NOTE
$ENERGY SAVER Key
CCan save power while the copier is not in use.
%INTERRUPT Key
CInterrupts other copy or print jobs while making copies.
&FUNCTION Key
CUse when changing the paper size, initial values for functions (default values) and key operator settings.
(RESET Key
CResets all features to the initial power-on state.
)CLEAR Key
CClears the copy count in the display.
*STOP Key
CStops the copy run.
+ALARM LED (RED)
CLights when trouble occurs.*
∗When the machine detects a problem or an alarm status is activated, the
+Alarm LED lights up or begins to flash.
LED Lights: Machine detected a trouble status
  ANo paper in the selected tray or toner has run out.
  AMachine detected trouble, such as paper misfeed or jam.
LED Flashes: Machine detected an alarm status
  A No paper in the tray. (tray not selected)
  A Running low on toner etc.
CThe Control Panel displayed above shows only copier functions. Please refer
to the appropriate operating instructions for other control panel functions.
(Refer to page 18 for details on the ORIGINAL SIZE/COPY SIZE Keys.) -ACTIVE LED (GREEN)
CLights when machine is active.
.PRINT DATA LED (GREEN)
CLights when print data receive.
Before Starting
Control Panel
∗
∗
FAX/EMAIL ON LINE LED for optional Facsimile/Internet Fax functions
Print ON LINE LED for Printer functionTouch Panel
Display
P012-013_4510(pb).p657/31/02, 10:44 AM 13 
						

							14
B4·FLS
Control Panel
Touch Panel Display
ATTENTION
Touch Panel
Display
CUse only soft finger pressure to activate the Touch Panel Display. DO NOT
USE SHARP OBJECTS such as pens, fingernails etc., as this may damage
the panel.
P014-015_4510(pb).p657/31/02, 10:44 AM 14 
						

							15

Touch Panel Display Indications
No. Contents
#Warning Indications
?: Add Tonerk: Add Paper2: Call ServiceB: Waste Toner (Call Service)
$Original Icon
%Original Size Indication
&SADF/Multi-Size Feed Mode Indication
(Rotate Mode Indication
)Number of Copies
*Machine / User Error Code Indication (E1-01, U13, etc.)
+Copy Icon
-Copy Size Indication
.Reserve a Job Button
/Finisher Functions Indication
0Machine Outline with Tray Selection
1Paper Level and Size Indication
2Paper Tray Selection Button
3Tandem/Remote Button Indication
4Tandem/Remote Button
5Density Indicator (7 steps)
6Manual Exposure Select Buttons (Lighter and Darker)
7Original Mode Select Button (Text; Text / Photo; Photo)
Control Panel
8Copy Image and Paper Image Indication
9Copy Ratio Indication
:Original Image Indication
;Function Categories
=Proof Set Button
?Job Settings Button
AJob Queue Button
BCompletion Notice Button
See  Page
--
35
--
37
20
20
14
14
14
16
16
16
16 - 58
19
14
25
26
Before Starting
--
16
--
120
--
16
55
--
--
16
P014-015_4510(pb).p657/31/02, 10:44 AM 15 
						

							16
B4·FLS
Basic Menu
Full Size Copying

 

 


Copying the Same Size Originals (1:1)
Copy size is automatically selected.
1
Place the
Original(s)ORIGINAL SIZE Keys Touch Panel Display
2
Number of Copies
(Up to 999)
3
Press START

 

 


Initial Screen
(When placing A4 size originals)
Select the ORIGINAL SIZE
A4 and A5 size can be switched between Portrait
and Landscape mode.Manual Exposure Select buttons
(LIGHTER and DARKER)
#Touch the LIGHTER or DARKER button.
$Select the Original(s)
TEXT : Originals are mainly composed of text.
TEXT/PHOTO : Combined originals with text and photo.
PHOTO : Originals are mainly composed of photo. JOB SETTINGS button
CEach setting selected will be indicated on the display.

 

 


Manually Selecting Exposure Control or Original Size
Original Mode Select button
(TEXT; TEXT/PHOTO;  PHOTO)
P016-017_4510(pb).p657/31/02, 10:44 AM 16 
						

							17
# Place the sheets of paper into
the tray. (Approximately up to
50 A4 size sheets/80 
g gg g
g/m
2)
ATTENTION
Basic Menu

 

 


Using the Sheet Bypass
Copying on Special Paper, etc.
Open the Sheet Bypass. Pull out the Sheet Bypass Tray
until it stops.
Insert the paper until it stops.
$ Adjust the side guides.Incorrect adjustment may cause the
paper to wrinkle, misfeed or skew.
CDo not feed curled paper through the sheet bypass to avoid misfeed.
CCertain types of transparency film may not be compatible and may damage
your machine. Consult with an authorised Panasonic dealer for advice
regarding non-standard paper types. (Panasonic has tested “3M PP2500”
transparency film and found it to be compatible.)
Making Copies
Do not load paper above the upper
limit arrow indicated on Side Guides.
Sheet Bypass
Inappropriate Originals
CPaper with a smooth surface such as glossy
and coated papers
CTransparencies
COriginals with a Lead Edge that is “creased”,
“folded”, “punched” or “glued”CPaste-ups
CPressure sensitive or carbon backed papers
CPaper with excessive curl
CStapled originals
CFreshly printed copies from a laser printer
When copying the thick Booklet, open the ADF and check the ADF Hinge is returned to original
angle if ADF rear side is lifted up.
12

 

 


Notice for i-ADF
P016-017_4510(pb).p657/31/02, 10:44 AM 17 
						

							18
B4·FLS
Reduction or Enlargement Copying
NOTE

 

 


Copying with Preset Ratios
Basic Menu
1
Place the
Original(s)
2
Select the
COPY SIZE
3
Number of
Copies
CIf the desired copy size is different from the paper size loaded in the paper tray, use
sheet bypass. (See page 17)
CPress the RESET key to cancel the reduction or enlargement mode.
4
Press START
Example: Reduction
ORIGINAL SIZE COPY SIZE
A3A4
The correct ratio is automatically selected.
Reduction and enlargement ratios (%)
ORIGINAL
SIZECOPY SIZE
A3 B4 A4 R A5
A3
B4
A4 R
A5
CWhen changing the paper size, touch
the PAPER TRAY button.
100 87 71 50
115 100 82 58
141 122 100 71
200 173 141 100
P018-019_4510(pb).p657/31/02, 10:44 AM 18 
						

							19
Making Copies
B4·FLS
NOTE
Proof Copying

 

 


Proof Copying
Allows you to make one proof set, before proceeding to copy a large multi-set with various
settings.
1
Place the
Original(s)
(Up to 70)
Basic Menu
(2)
COPY SIZE
(Reduction/
Enlargement
Only)
4
Set function and Proof
Copying
3
Number
of Copies
5
Press
START
#Place the Originals on the ADF, adjust the
settings to your needs, select the number of
copies desired.
$Set PROOF SET button.
%Press START, then one Proof Copy is made.
CIf the Proof Copy is OK, press the YES button
and the remaining number of sets will be printed.
CIf the Proof Copy is NG, press the NO button to
display the Basic Menu. Adjust the settings to
your requirements, place the originals back on
the ADF and press START to make another
Proof Copy. The process can be repeated until
the desired results are obtained.
CPress the PROOF SET button again if the Proof Copying mode was reset.
CNumbers in parenthesis “(   )” represent that, an additional step is required to
activate the feature.
P018-019_4510(pb).p657/31/02, 10:44 AM 19 
						

							20
B4·FLS
NOTE
Tandem/Remote Copying

 

 


(Required installation of optional Hard Disk Drive/DA-HD60, network
setup(See page 65)and registration of parameter of the user machine(See
page 21).)
C50 % of the total copying set(s) are split between other copiers on the network. (Tandem Copying)
CAll of the copying sets will be printed on other copiers in the network. (Remote Copying)
1
Place the
Original(s)
Basic Menu
(2)
COPY SIZE
(Reduction/
Enlargement
Only)
4
Set Tandem/Remote
Copying
3
Number
of Copies
5
Press
START
#Select TANDEM/REMOTE button on
BASIC MENU.
CThe selected Remote printing copier, must be either DP-6010, DP-4510 or
DP-3510. For the copier to function as a Remote/Tandem Copier it has to be
setup in advance.
CTo reset the Remote/Tandem mode, press the CANCEL button.
$Select Station.
If the desired Station(Machine Name) is
not displayed for selection, register the
Station(Machine Name) according to the
procedure on the next page.
%Select TANDEM button or REMOTE
button.
&Touch the OK button.
P020_4510(pb).p657/31/02, 10:44 AM 20