Panasonic IR Light Ag Yrl30g Operating Instructions

							Model  AG- G
IR Light
Before operating this product, please read the instructions carefully and save this manual for future
reference.
VQT0L26 
						

							– 2 (E) –
indicates safety information.
$DO NOT REMOVE COVER BY UNSCREWING.
To reduce the risk of electric shock, do not remove cover.
No user serviceable parts inside.
Refer servicing to qualified service personnel.
$Do not use power supplies or voltages other than those indicated as
this may result in fire or electrical shock.
WARNING:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS
EQUIPMENT AWAY FROM ALL LIQUIDS–USE AND STORE ONLY
IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF
DRIPPING OR SPLASHING LIQUIDS, AND DO NOT PLACE ANY
LIQUID CONTAINERS ON TOP OF THE EQUIPMENT. 
						

							– 3 (E) –
ENGLISH
indicates safety information.
WARNING:
Do not look straight at the IR
light since it emits an infrared
beam of light when it is lighted.
You may damage your eyes if
you look straight at the light.
Precautions for use$The IR (infrared) light is used as a
photographic aid for shooting in the dark and
at night.  Do not use it for any other purpose.
$When the IR light is mounted on the camera-
recorder and the camera-recorder is to be
carried, do not hold the camera-recorder by
the IR light.$Avoid using or storing the IR light in the
following places:
OWhere the IR light will be exposed to the
intense rays of the sun, inside a vehicle
with all the windows closed or any other
high-temperature location
ONear a heating appliance or where the IR
light will be exposed to direct sunlight
OWhere it is very dusty
OWhere the IR light will be subjected to
violent vibration
$When the IR light is not going to be used or
when carrying it, be absolutely sure to set
the POWER switch to the OFF position and
remove the battery.
Before stowing away the IR light, allow it
cool off sufficiently first. 
						

							– 4 (E) –
Installing the batteryPush the battery straight in, and slide the
battery down until it clicks into place.
$To remove the battery, hold down the button
while at the same time sliding the battery up
until it can be taken out.Maintenance$Before proceeding with maintenance,
remove the battery.
$Do not use benzine or paint thinners for
maintenance purposes since they may
deform the IR light or cause its paint to peel
off.
$Wipe the IR light with a soft, clean cloth.  To
remove stubborn dirt, dip a cloth into some
kitchen detergent diluted with water, wipe off
the dirt, and then take up any remaining
moisture using a dry cloth.
Power sourcesUse a battery to power the IR light (see page
8).
ODo not use the AG-B15 AC adaptor kit. 
						

							– 5 (E) –
ENGLISH
Attention/AttentieOBatteries are used for the main power
source, memory back-up in the product and
remote controller.
At the end of their useful life, you should not
throw them away.
Instead, hand them in as small chemical
waste.
OVoor de primaire voeding en het
reservegeheugen van het apparaat,
alsmede voor de afstandsbediening, wordt
gebruik gemaakt van een batterij.
Wanneer de batterij uitgeput is, mag u deze
niet gewoon weggooien, maar dient u ze als
klein chemisch afval weg te doen. 
						

							– 6 (E) –
2
1 12
1 1
Mounting the IR light on the camera
2Tighten the anchoring ring to anchor the IR
light securely.
When doing so, use the screen to adjust
the emission position to adjust (horizontal)
the IR light.
OThe emission position cannot be
adjusted vertically.1Mount the IR light by sliding it into the
accessory shoe on the camera-recorder or
handle.
OBefore attempting to mount the IR light
into the accessory shoe of the camera-
recorder, pull out the viewfinder. 
						

							– 7 (E) –
ENGLISH
Operation
$POWER switch
OFF :The switch must always be set to
the OFF position when the IR light is not
going to be used.
WIDE :It is recommended that the switch
be set to the WIDE position for IR shooting
at distances up to 10 or so meters (11 or
so yards).
It is recommended that the IR light on the
camera-recorder also be used for IR
shooting at distances up to 5 meters (up to
5 yards).
SPOT :It is recommended that the switch
be set to the SPOT position for IR shooting
at distances in excess of 10 or so meters
(11 or so yards).
At this setting, a beam of infrared light can
be emitted up to distances of about 30
meters (32 yards).  However, the area
exposed to the beam of light will be
reduced.
The recommended IR shooting distances are
ones which apply when the AG-DVC30 (or
AG-DVC32) camera-recorder is used.$POWER lamp
This lights when the POWER switch is set to
either WIDE or SPOT position.
$IR CTRL dial
This dial is used to adjust the intensity of the
infrared beam of light.
Adjust the beam intensity to suit the distance
and brightness of the subject.
IR CTRL
PUSH
POWERSPOTWIDEOFF
POWERSPOTWIDEOFF
IR CTRL 
						

							– 8 (E) –Power supply:
DC 7.2 V
Power consumption:
3 W (maximum)
Specifications
Ambient operating temperature:
32°F to 104°F (0°C to 40°C)
Ambient operating humidity:
10% to 85% (no condensation)
Weight:
0.352 lb (160 g)
Dimensions (WkHkD):
2 
11/16k4 3/16k1 7/8inches
(67k106k47 mm)
Maximum beam emission distances:
At the WIDE setting:
Approx. 10 meters (11 yards)
At the SPOT setting:
Approx. 30 meters (32 yards)indicates safety information.
CGR-D16CGR-D16S
CGP-D28
CGP-D28S Approx. 250 minutes
Approx. 390 minutesBattery Continuous beam
emission time
OThe lengths of time given above are the
periods during which the IR light can emit an
infrared beam when a sufficiently charged
battery is used at an ambient operating
temperature of 68°F (20°C) and an ambient
operating humidity of 60%, and they are
approximations only.  At other temperature
or humidity levels, these periods may be
shorter.
OTo charge the battery, use the AG-B15 AC
adapter kit. 
						

							– 9 (E) –
ENGLISH
Memo 
						

							– 2 (G) –
ist die Sicherheitsinformation.
$NICHT DIE ABDECKUNG ABSCHRAUBEN.
Zur Vermeidung von elektrischem Schlag darf das Gehäuse nicht geöffnet
werden.   Im Geräteinneren befinden sich keine Teile, die vom Benutzer
gewartet werden können.
Wartungs- und Reparaturarbeiten grundsätzlich autorisiertem
Kundendienstpersonal überlassen.
$Um die Gefahr von Brand und elektrischem Schlag zu vermeiden, das
Gerät ausschließlich mit den angegebenen Anschlußwerten betreiben.
WARNUNG:
UM BRAND- ODER STROMSCHLAGGEFAHR ZU REDUZIEREN, MUSS
DIESES GERÄT VON ALLEN FLÜSSIGKEITEN FERNGEHALTEN
WERDEN. VERMEIDEN SIE GEBRAUCH UND LAGERUNG DES
GERÄTES AN ORTEN, AN DENEN DIE GEFAHR BESTEHT, DASS ES
MIT FLÜSSIGKEITEN BETROPFT ODER BESPRITZT WIRD, UND
STELLEN SIE KEINE FLÜSSIGKEITSBEHÄLTER AUF DAS GERÄT.