Panasonic Kx Flb756 Laser Multifunction Fax Machine Users Manual

							21
Setup
For fax advantage assistance, call 1-800-435-7329.
Setting your facsimile telephone number
1
Press p.
Display:
2
Press (or )until the following is
displayed.
3
Press w.
4
Enter your facsimile telephone number, up to 
20 digits, using the dial keypad.
Example:
5
Press w.
The next feature will be displayed.
6
Press p.SENDING REPORT
MODE=ERROR   [±]
NO.=1234567
NO.=
YOUR FAX NO.
PRESS SET
SYSTEM SET UP
PRESS NAVI.[IH]
STOP
SET
MENUDisplay
(Hyphen)
FLASH
(Delete)
Note:
 You can enter your facsimile telephone number by
pressing +or -in step 4. In this case, press 
)to move the cursor.
 The *button replaces the digit with a “+” and the 
#button replaces it with a space.
Example(using the dial keypad):  +234  5678
Press *234#5678.
 To enter a hyphen in a telephone number, press
k.
To correct a mistake
 Press (or )to move the cursor to the incorrect
number, and make the correction.
To delete a number
 Move the cursor to the number you want to delete and
press {.
KX-FLB756 (019-022)  03.4.14  9:08 PM  Page 21 
						

							22
Volume
For fax advantage assistance, call 1-800-435-7329.
Adjusting volume!
Ringer volume
4 levels (high/middle/low/off) are available.
While the unit is idle, press +or -.
To turn the ringer off:
1.Press -repeatedly until the following is
displayed.
Display:
2.Press w.
 To turn the ringer back on, press +.
While the ringer volume is set to off:
When a call is received, the unit will not ring and
will display the following.
INCOMING CALL
RINGER OFF
RINGER OFF= OK?
YES:SET/NO:STOP SET
Display
Ringer pattern
You can select one of three ringer patterns. Change the
setting (feature #17 on page 62). The ringer pattern
you selected will sound when the unit receives a call.
Handset receiver volume
5 levels (high to low) are available.
While using the handset,press +or -
Monitor volume
8 levels (high to low) are available.
While using the monitor,press +or -.
KX-FLB756 (019-022)  03.4.14  9:08 PM  Page 22 
						

							Automatic Dialing
23
For rapid access to frequently dialed numbers, the unit provides 12 entries for one-touch dial.
Stations 1 to 3 can be used alternatively as broadcast keys (p. 36).
1
Press prepeatedly until the following
is displayed.
Display:
/
2
For stations 1–3:
Press one of the station keys.
Example:
Press wto go to the next prompt.
For stations 4–6:
Press one of the station keys.
For stations 7–12:
Press o, then press one of the station
keys.
3
Enter the name, up to 10 characters (see
page 20 for instructions).
Example:
4
Press w.
Example:
5
Enter the telephone number, up to 30 digits,
using the dial keypad.
Example:
If you want to enter a hyphen, press
k.
6
Press w.
!
/
To program other entries, repeat steps 2 to 6.
7
Press {to exit the program.DIRECTORY SET
PRESS NAVI.[
IH]
DIRECTORY SET
PRESS STATION OR
REGISTERED

=1114497

=
NAME
=John
STORE:PRESS SET
STATION 1
DIAL MODE    [±]
DIRECTORY SET
PRESS NAVI.[
IH]
DIRECTORY SET
PRESS STATION OR
Helpful hint:
You can confirm the stored entries on the
telephone number list (p. 80).
Note:
A hyphen or a space entered in a telephone
number counts as two digits.
To correct a mistake
Press (or )to move the cursor to the
incorrect character/number, and then make
the correction.
To delete a character/number
Move the cursor to the character/number you
want to delete, and press {.
Storing names and telephone numbers
into one-touch dial!
Station keys
(Delete)
STOP
SET
MENU(Hyphen)
FLASH
LOWER
KX-FLB756 (023-030)  03.4.14  9:09 PM  Page 23 
						

							24
Automatic Dialing
Storing names and telephone numbers
into navigator directory!
For rapid access to frequently dialed numbers, the unit provides the navigator directory 
(100 entries).
(Delete)
STOP
SET
MENU
(Hyphen)
FLASH
Note:
 When the following is displayed in step 6, you
can store only 5 more entries.
Display:
 If there is no space to store new entries, the
following is displayed in step 6. 
Erase unnecessary entries (p. 25).
 A hyphen or a space entered in a telephone
number counts as two digits.REGISTERED
DIRECTORY FULL
REGISTERED
SPACE= 5 DIRS.
Helpful hint:
 For your convenience, HELP-FAX (1-800-435-7329)
has been pre-programmed.
If you cannot solve a problem after trying the help
function (p. 9), call using this entry (p. 26).
If unnecessary, you can erase it (p. 25).
 You can confirm the stored entries on the telephone
number list (p. 80).
1
Press prepeatedly until the following
is displayed.
Display:
/
2
Press (or ).
3
Enter the name, up to 10 characters (see
page 20 for instructions).
Example:
4
Press w.
5
Enter the telephone number, up to 30 digits,
using the dial keypad.
Example:
 If you want to enter a hyphen, press
k.
6
Press w.
!
 To program other entries, repeat steps 3 to 6.
7
Press pto exit the program.NAME=  
STORE:PRESS SET
REGISTERED
NO.=5552233
NO.=   
NAME=Alice
STORE:PRESS SET
NAME=  
STORE:PRESS SET
DIRECTORY SET
PRESS NAVI.[
IH]
DIRECTORY SET
PRESS STATION OR
To correct a mistake
 Press (or )to move the cursor to the
incorrect character/number, and then make
the correction.
To delete a character/number
 Move the cursor to the character/number you
want to delete, and press {.
KX-FLB756 (023-030)  03.4.14  9:09 PM  Page 24 
						

							25
Automatic Dialing
STOP
SET
MENU
1
Press (or ).
Display:
2
Press +or -until the desired entry is
displayed.
Example:
!
!
3
Press p.
Example:
4
Press *to select “EDIT”.
Example:
 If you do not need to edit the name, skip to
step 6.NAME=Mary
STORE:PRESS SET
NAME=Mary
EDIT=?DELETE=#
Mary 
SEND:PRESS SET
Mary 
EDIT:PRESS MENU
Mary 
0123456
DIRECTORY  [+ -]
1
Press (or ).
Display:
2
Press +or -until the desired entry is
displayed.
Example:
!
!
Peter
SEND:PRESS SET
Peter
EDIT:PRESS MENU
Peter
9876543
DIRECTORY  [+ -]
5
Edit the name (see page 20 for
instructions).
6
Press w.
Example:
 If you do not need to edit the
telephone number, skip to step 8.
7
Edit the telephone number. For
further details, see page 24.
8
Press w.
REGISTERED
=0123456
You can erase an entry stored in one-touch dial and navigator directory.
Editing a stored entry!
You can edit a name or number that is stored in one-touch dial and navigator directory.
3
Press p.
Example:
4
Press #to select “DELETE”.
 To cancel erasing, press {.
5
Press w.
 The stored name and number are
erased.DELETED
DELETE OK?
YES:SET/NO:STOP
NAME=Peter
EDIT=?DELETE=#
Station key number 
for one-touch dial
Erasing a stored entry!
KX-FLB756 (023-030)  03.4.14  9:09 PM  Page 25 
						

							26
Automatic Dialing
Making a phone call using one-touch dial
and navigator directory!
Before using this feature, program the desired names and telephone numbers into one-touch dial
and navigator directory (p. 23, 24).
Using one-touch dial
Station keys
STOP
MONITOR
LOWER
1
Press qor lift the handset.
Display:
/
2
For stations 1–6:
Press the desired station key.
Example:
For stations 7–12:
Press o, then press the desired 
station key.
The unit will start dialing automatically.TEL=
TEL=
PRESS NAVI.[
IH]
TEL=
PRESS STATION OR
Using the directory
1
Press (or ).
Display:
2
Press +or -until the desired entry is
displayed.
Example:
!
!
If the desired name has not been stored,
press {and dial the number
manually.
3
Press qor lift the handset.
The unit will start dialing automatically.
Lisa
SEND:PRESS SET
Lisa
EDIT:PRESS MENU
Lisa
2233445
DIRECTORY  [+ -]
To search for a name by initial
Example: “Lisa”
1.Press (or ).
2.Press +or -to enter the directory.
3.Press 5repeatedly until any name with the
initial “L” is displayed (see the character
table on page 20).
 To search for symbols (not letters or
numbers), press *.
4.Press +until “Lisa” is displayed.
 To stop the search, press {.
 To make a call, press qor lift
the handset.
KX-FLB756 (023-030)  03.4.14  9:09 PM  Page 26 
						

							Caller ID
27
Caller ID service from your phone company!
This unit is compatible with the Caller ID service offered by your local telephone
company. To use this feature, you must subscribe to the Caller ID service.
How Caller ID is displayed
Change the FAX ring setting (feature #06 on page 61) to 2 or more rings beforehand.
Note:
 If the unit is connected to a PBX (Private Branch Exchange) system, you may not receive the caller
information. Consult your PBX supplier.
 If the unit cannot receive caller information, the following will be displayed.
The caller dialed from an area which does not provide Caller ID service.
The caller requested not to send caller information.
The caller made a long distance call.
LONG DISTANCE
PRIVATE CALLER
OUT OF AREA
The calling party’s name or telephone number will be displayed after the first ring.
You then have the option of whether or not to answer the call depending on the caller.
The unit will automatically store the caller information (name, telephone number and the time of
the call). You can view the caller information (see the next page) and print the Caller ID list 
(p. 80).
To confirm caller information using the Caller ID list
The unit will store information for the most recent 30 callers.
— To print manually, see page 80.
— To print automatically after every 30 new calls, activate feature #26 (p. 64).
KX-FLB756 (023-030)  03.4.14  9:09 PM  Page 27 
						

							Caller ID
28
Display while viewing
When the unit could not receive a name.
When no calls have been received.
To stop viewing
Press {after step 2.
NO CALLER DATA
NO NAME RCVD
1
Press b.
Example:
2
Press +to search from the most recent
caller information. 
Press -to search from the oldest caller
information.
 To send a fax using the scanner glass, 
see page 32.
3
Press qor lift the handset to call
back the displayed party.
 The unit will start dialing automatically.
 To send a fax using the auto document
feeder – insert the document FACE DOWN
into the feeder and press i
(p. 31).
2 NEW CALLS
PRESS NAVI.[+ -]
FACE DOWN
FACE
DOWN
STOP
FAX START
CALLER ID
MONITOR
Viewing and calling back using caller information!
You can easily view caller information and call back.
Important:
 Calling back will not be possible in the following cases:
— The telephone number includes data other than numbers (i.e. :or #).
— The caller information does not include a telephone number.
To edit the telephone number for calling back
Press *repeatedly after step 2.
Each time you press *, the telephone number will be changed as follows:
2.Local telephone number  (area code omitted)
1.1  –  Area code  –  Local telephone number  (“1” added)
Area code  –  Local telephone number
1  –  Local telephone number  (“1” added and area code omitted)
4. 3.
To display the caller’s telephone number
Press brepeatedly after step 2.
Example:
=1-345-678-9012
Jul. 20 11:20AM
√SAM LEE
Jul. 20 11:20AMThis means the caller has already
been viewed or answered.
(2 new calls are received)
KX-FLB756 (023-030)  03.4.21  6:41 PM  Page 28 
						

							Caller ID
29
STOP
SET
MENU1
Press prepeatedly until the following
is displayed.
Display:
2
Press w.
3
Press w.
 To cancel erasing, press {, then
p.
4
Press w.
5
Press {to exit the program.ERASE COMPLETED
ALL ERASE OK?
YES:SET/NO:STOP
CALL LIST ERASE
PRESS SET
CALLER SET UP
PRESS SET
Erasing caller information!
KX-FLB756 (023-030)  03.4.21  6:41 PM  Page 29 
						

							Caller ID
30
Station keys
SET
MENU
LOWER
CALLER ID
Storing caller information into one-touch dial 
and navigator directory!
Important:
 This feature is not available in the following cases.
— The telephone number includes data other than numbers (i.e. :or #).
— The caller information does not include a telephone number.
1
Press b.
Example:
2
Press +or -until the desired entry is
displayed.
Example:
3
Press p.
Example:
/
4
For stations 1–3: 
Press the desired station key.
Example:
Press w.
Example:
Press w.
Example:
For stations 4–6: 
Press the desired station key.
Example:
Press w.
Example:
For stations 7–12: 
Press o, then press the desired
station key.
Example:
Press w.
Example:
=134567890
NAME=SAM LEE
STORE:PRESS SET
=134567890
NAME=SAM LEE
STORE:PRESS SET
=134567890
NAME=SAM LEE
STORE:PRESS SET
STATION 1
DIAL MODE    [±]
SAM LEE
PRESS NAVI.[
IH]
SAM LEE
PRESS STATION OR
SAM LEE
Apr. 14 11:50AM
2 NEW CALLS
PRESS NAVI.[+ -]
Note:
 You can confirm the stored entries on the
telephone number list (p. 80).
 The unit can only store a name of up to 10
characters long. 
 To edit a name and number, see page 25.
 If you enter a new entry into a station key, the
previous entry will be overwritten.
 If you use stations 1–3 as broadcast keys,
you cannot store caller information for
stations 1–3.
For navigator directory:
Press (or ).
Example:
Press w.
Example:
5
Press w.
REGISTERED
NO.=134567890
NAME=SAM LEE
STORE:PRESS SET
KX-FLB756 (023-030)  03.4.21  6:41 PM  Page 30