Panasonic Kx Tgf340 Operating Instructions Manual

Sub-menu 1 Sub-menu 2 Settings Code
Key detector
s
etting *6
– 1: Add new
device  (for
Detector1 )*7
– 2: Add new
device  (for
Detector2 )
– 3: Add new
device  (for
Detector3 )
– 4: Add new
device  (for
Detector4 )Change name
* 1
Detector1 #6561–
Detector2 *
 8
#6562* 8
Detector3 *
 8
#6563* 8
Detector4 *
 8
#6564* 8
Registration –#6571 –
#6572 *
 8
#6573 *
 8
#6574 *
 8
Deregistration –#6581 –
#6582 *
 8
#6583 *
 8
#6584 *
 8
Call block *
 1
Block a single
n
umber –
#21721
Block range of
n
 umbers –
22...

Sub-menu 1 Sub-menu 2 Settings Code
Auto talk
* 9
–On 
< O
ff > #200
16
Set tel line Set dial mode*
 1
Pulse
 #120
14
Set flash time *
 1, *10
900 ms

600 ms
400 ms 300 ms
250 ms
200 ms 160 ms
110 ms
100 ms 90 ms
80 ms #121
17
Set line mode *
 1, *11
A < B> #122–
Call sharing *
 1
– 
Off #194
17
Registration Register handset –#13039
Deregistration *
 2
–#13139
Power failure –
Off #152
19
Change language Display  
Español #110
13
Voice prompt *
 1
 
Español #112
13Main menu:   “
C
ustomer support...

Main menu:   “
Key detector ”*6 Sub-menu 1 Sub-menu 2 Settings Code
Search
––#655 –
Battery check ––n
 
Base unit
Main menu:   W “Phonebook ”Operation Code
Viewing the phonebook entry.
#28025Main menu:   “
C
aller list ”Operation Code
Viewing the caller list.
#21340Main menu:   “
A
nswer device ”Sub-menu 1 Sub-menu 2 Settings Code
Screen call
–
Off #310
48Main menu:   “
S
ettings ”Sub-menu 1 Sub-menu 2 Settings Code
Ring adjustment
Ringer volume Off–
6  #160–
Silent mode
– O

n/Off On
<
O
ff > #238
35...

Sub-menu 1 Sub-menu 2 Settings Code
Auto intercom
–On
<
O
ff > #273
19
Caller ID edit
(
 Caller ID number auto
edit) –

Off #214
41
Change language
(
 Display) –
 
Español #110
13Main menu:   “
C
ust. Support ”Operation Code
Displaying customer support Web address.
#680–*1 If you program these settings using one of the units, you do not need to program the same
i
 tem using another unit.
*2 This menu is not displayed when scrolling through the display menus. It is only available in direct command code....

Alarm
A n alarm sounds at the set time for 1 minute
and is repeated 5 times at 5 minute intervals
(snooze function). A text memo can also be
displayed for the alarm. A total of 3 separate
alarm times can be programmed for each
handset. You can set one of 3 different alarm
options (once, daily, or weekly) for each alarm
time.
Important:
R Make sure the unit’s date and time setting
is correct (page 13). Handset
1 MM

ENUN#720
2 Mb N: Select the desired alarm.  a
M SELECT N
3 Mb N: Select the desired alarm...

3
Enter the desired hour and minute you
wish to start this feature.
4 *: Select  “AM ” or  “PM ”.  a  M OK N
5 Enter the desired hour and minute you
wish to end this feature.
6 *: Select  “AM ” or  “PM ”.
7 MSAVE N a  M OFF N Base unit
1 MM

ENUN#238
2 Mb N: Select the desired setting.  a
M SAVE N
R If you select  “Off ”, press  MEXIT N to
exit.
3 Enter the desired hour and minute you
wish to start this feature.
4 MAM/PM N: Select  “AM ” or  “PM ”.  a  M OK N
5 Enter the desired hour and minute you
wish...

– between handsets
–
between a handset and the base unit Handset
1 MM

ENUN#268
2 Mb N:  “On ” a  M SELECT N
3 Mb N: Select the desired unit’s number to
monitor with.  a M SAVE N
R “Baby monitor ” will be displayed.
R The registered unit’s name/number is
displayed.
Note:
R When this feature is on, another handset or
the base unit can hear the monitored
handset by making an intercom call. To monitor from an outside line
I

f you enable this feature, the unit will call a
pre-programmed phone number when...

Baby monitor sensitivity
Y
ou can adjust the sensitivity of the baby
monitor. Increase or decrease the sensitivity to
adjust the sound level needed to trigger the
baby monitor feature.
R This feature cannot be set during a
monitoring call. Handset
1 P

ress  MMENU N on the handset being
monitored.
2 Mb N:  “Sensitivity level ” a
M SELECT N
3 Mb N: Select the desired setting.  a
M SAVE N a  M OFF N Answering the baby monitor
n
W

hen monitoring with a unit:
Handset:  Press M N
 
to answer a call.
Base...

Registering a handset to the
b ase unit
The supplied handset and base unit are
pre-registered. If for some reason the handset
is not registered to the base unit, re-register
the handset.
1 Handset:
MMENU N#130
2 Base unit:
Press and hold  MLOCATOR N for about 5
seconds.
R If all registered handsets start ringing,
press  MLOCATOR N again to stop, then
repeat this step.
3 Handset:
Press  MOK N, then wait until a long beep
sounds. Deregistering a handset
A
  handset can cancel its own registration to
the...

Using Caller ID service
I mportant:
R This unit is Caller ID compatible. To use
Caller ID features, you must subscribe to a
Caller ID service. Contact your phone
service provider for details. Caller ID features
Handset / Base unit
W
 hen an outside call is being received, the
caller information is displayed.
Caller information for the last 50 callers is
logged in the caller list from the most recent
call to the oldest.
R If the unit cannot receive caller information,
the following is displayed:
–“Out of...