Panasonic Projector Pt Dw7000e Operating Instructions

DLPTMBased Projector  Commercial Use
Operating Instructions
Read these instructions completely before operating this unit.
TQBJ 0147-7
POWERON OFFRGB1RGB2AUX
MENU
STD
LENSOSD1
4
72
5
83
6
9
0
NEXTUSERLIGHTID ALLASPECTID SETProjectorComputerNumetric
BRIGHTCONTRAST ON SCREENSYSTEMSELFUNC1D.ZOOM
ENTERPA G E  UP
PA G E  DOWN
VIDEOSHUTS-VIDEOFREEZESHUTTER
AUTO
SETUP
LASER ON/OFF
Model No. PT-D7700E
PT-DW7000E
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO 

2
Dear Panasonic Customer:
This instruction booklet provides all the necessary operating information that you might require. We hope it will help
you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLPTM
based projector.
The serial number of your product may be found on its back. You should note it in the space provided below and
retain this booklet in case service is required.
Model number: PT-D7700E / PT-DW7000E
Serial number:
IMPORTANT SAFETY...

3
ENGLISH
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY
, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the
replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSl to BS1362.
Check for the ASTA mark  or the BSl mark  on the body of the fuse.
If the plug contains a removable fuse cover,...

4
Adjusting the position .............................................51Shift adjustment...............................................................51
Size adjustment ...............................................................52
Clock phase adjustment ..................................................53
Keystone distortion correction .........................................54
How to use ADVANCED MENU ...............................55DIGITAL CINEMA REALITY...

5
ENGLISH
Precautions with regard to safety
WARNING
If a problem occurs (such as no image) or if you notice smoke or a strange smell coming
from the projector, turn off the power and disconnect the power cord from the wall outlet.
• Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.
• Check that no more smoke is coming out, and then contact an Authorized  Service Centre for repairs.
• Do not attempt to repair the projector yourself, as this can be...

6
Precautions with regard to safety
Do not place liquid containers on top of the projector.
• If water spills onto the projector or gets inside it, fire or electric shocks could result.
• If any water gets inside the projector, contact an Authorized Service Centre. 
Do not insert any foreign objects into the projector.
• Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing
so can result in fire or electric shocks.
After removing the battery...

7
ENGLISH
Accessories
Check that all of the accessories shown below have been included with your projector.
Do not look into the lens while the projector is being used.
• Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.
Do not bring your hands or other objects close to the air outlet port.
• Heated air comes out of the air outlet port. Do not bring your hands or face, or objects which cannot withstand heat.
Do not use the old lamp...

8
Precautions on handling
Precautions on transport
The projection lens is susceptible to vibrations and
impacts. Be sure to always remove the lens during
transport.
Precautions on installation
Be sure to observe the following precautions when
installing the product.
Avoid installing the product in a place
exposed to vibrations or impacts
.
If the projector is installed in a place where
vibrations are transmitted from a source of
driving power and others or mounted in a car or
a vessel, vibrations or...

ENGLISH
9
The projector is provided with a number of terminals and optional accessories to enable various system expansions.
Both input and output are provided to all terminals on the main unit.
The following are some examples of system expansion:
Examples of system expansion
System 1
Stacking two projectors with the
stacking brackets can double the
picture brightness.
System 3
PC equipped with a DVI-D input module (an
optional item) can be attached to the
projector for computer image viewing...

10
Name and function of parts 
< When the operation mode selector  is
set to Projector >
Remote control operation indicator lamp
The lamp flashes when any remote control button
is pressed.
POWER ON button (page 33)
Turns on the power if the MAIN POWER has been
put to the “l” position.
POWER OFF button (page 34)
Turns off the power if the MAIN POWER has been
put to the “l” position.
AUTO SETUP button (page 37)
Pressing this button while projecting an image
automatically corrects the picture positioning on...