Panasonic Projector Pt Ez570u Operating Instructions

							ENGLISH - 41
Basic Operation
Projecting
Check the connections of the peripheral devices and connection of the power cord (Æpage 36) and switch on the 
power (Æpage 38) to start the projector. Select the image and adjust the state of the image.
Selecting the image
Select an input signal.
Side Control/Remote Control Operation J
You can press the  button on the side control or the remote control to select INPUT 1/2/3 as input 
source.
Remote Control Operation J
Press the , , or  button on the remote control. Each time you press the  button, the input signal will be changed. 
Attention
Images may not be projected properly depending on the connected device a\
nd DVD, video tape, etc. to be played. Select a  z
system format that is suitable for the input signal [Y, Pb/Cb, Pr/Cr ] or [RGB] in the [Input] menu (Æpage 50).
Check the aspect ratio of the screen and the image and select the optimu\
m aspect ratio under the [Screen] menu  z
(Æpage 59).
Adjusting the image
Adjusting the position of the lens J
Press the  button on the remote control or the  button on the side control.1 ) 
[Lens shift] is displayed on the screen for four seconds. z
While the display appears, press ▲▼2 ) ◄► to move the image horizontally and vertically.
As you move the image, there is a certain position at which the arrows p\
ointing up, down, left and right turn red. This  z
position is the center for the lens.
At positions of maximum shift, the arrows disappear. z
The projector stores the setting made using the lens shift function when\
 the power is turned off. z
When the position of the image is shifted, the image may become a little\
 darker. z
Press and hold the  button or  button for more than 5 \
seconds, the lens shift will be return to the  z
center position.
The figure below shows an example of when the standard lens is attached.
Adjusting the zoom and focus J
Press the  button and the  button on the remote control.1 ) 
[Zoom] and [Focus] are displayed on the screen for four seconds. z
While the display appears, press ▲▼ to adjust the zoom and focus.2 ) 
Note
When [Display] is set to [Off], the adjustment screen will not appear. z
It is recommended that the images are projected continuously for at leas\
t 30 minutes before the focus is adjusted. z
The display position can be shifted upward up to 60% elevation of the display.
When the lens is shifted to top.When the lens is shifted to bottom.
When the lens is shifted to leftmost.When the lens is shifted to rightmost.
The display position can be shifted downward up to 60% low level of the display.
The display position can be shifted to the left in up to 10% width of the display.
The display position can be shifted to the right in up to 10% width of the display.




Lens shift  
						

							42 - ENGLISH
Basic Operation
Basic operations by using the remote control
Using the SHUTTER/ AV 
MUTE button 
*   button (Only for EZ570 series, EW630 
series and EX600 series) 
This function allows you allows you to completely 
block out light to the screen.
 button*
Press the  button on the 
remote control.
Note
For details, see “Setting” of Main menu. ( zÆpage 69)
*   button (Only for EW530 series and 
EX500 series) 
0â0÷0Á0î0ö0õ0æ button*
Press the  button on the 
remote control.
Press the < AV MUTE> button on the remote control 
to black out the image. To restore to normal, press the 
< AV MUTE> button again or press any button. 
Note
When use the  button to release the [ zAV mute] 
function, the mute function cannot be operated at the 
same time.
Switching the input signal
You can switch the input signals to project.
 buttons
Press the  button or the // button on the 
remote control.
The input source changes each time you press the 
 button as follows:
Input 1 --> Input 2 --> Input 3 --> ...
The input source changes each time you press the 
// button as follows:
Note
Whether the input search function is available or not  z
after you pressed the  button, it depends on the 
setting of the [Input button] in the Setting menu. 
(Æpage 63)
black out projected image
INPUT 1 button
Input 1
RGB(PC analog)
RGB (Scart)
HDMI
DVI-D(HDCP)
DVI-D
INPUT 2 button
Input 2
Video
Y,Pb/Cb,Pr/Cr
RGB
INPUT 3 button
Input 3
Video
Y,Pb/Cb,Pr/Cr
S-video 
						

							Basic operations by using the remote control
ENGLISH - 43
Basic Operation
Using the MENU button
This function allows you to open or close the On-
Screen Menu.
 button
Press the  button on the remote 
control.
Note
For details, please refer to “Menu Navigation”.   z
(Æpage 47)
Using the AUTO PC ADJ 
button 
This function allows you to adjust the computer screen 
easily.
 button
Press the  button on the 
remote control.
Note
For details, see “AUTO PC adjust” of Main menu.  z
 (Æpage 52)
Controlling the volume of the 
speaker
You can control the volume of the projector’s speaker 
or audio output.
 buttons
Press the  (+/–) buttons on the side control 
or on the remote control to adjust the volume. The 
volume dialog box appears on the screen for a few 
seconds.
Note
For details, see “Volume” of "Sound" under Main menu. z
(Æpage 62)
Using the IMAGE SELECT 
button 
This function allows you to operate the image 
selection directly.
 button
Press the  button on 
the remote control.
Note
For details, see “Image select” of Main menu.   z
(Æpage 55)
Using the MUTE button
Press this button on the remote control to temporarily 
turn off the sound.
 button
Press  button on the remote 
control. 
Note
To turn the sound back on, press this button again or  z
press the  (+/–) buttons. (Æpage 62) 
Using the IMAGE ADJUST 
button 
This function allows you to adjust the image.
 button
Press the  button on 
the remote control.
Note
For details, see “Image adjust” of Main menu.   z
(Æpage 56) 
						

							Basic operations by using the remote control
44 - ENGLISH
Basic Operation
Using the P-TIMER button
Press the  button on the remote control to 
operate the Count up/Count down function.
 button
Press  button on the remote 
control.
Note
Press the  button to start the count time.  z
Press the  button again to stop the count 
time. Press the  button to restart the count. 
To cancel the [P-timer] function, press and hold the 
 button. (Æpage 68)
Using the ECO button
Press this button to display the Eco management 
menu.
 button
Press  button on the remote 
control. 
Note
For details, see “Eco management” of "Setting".  z
(Æpage 67)
Using the SCREEN button
This function allows you to select screen mode or 
change the screen size.
 button
Press the  button on the 
remote control.
Note
For details, see “Screen” of Main menu. ( zÆpage 59)
Using the FREEZE function
You can freeze the projected image and stop the 
sound temporarily, regardless of the playing condition 
of the connected device.
 button
Press the  button on the remote control to 
freeze the picture on the screen, meanwhile, volume 
is muted. To cancel the Freeze function, press the 
 button again or press any other button.
Fig.1 will appear on the screen while the Freeze 
function is working.
 Fig.1
Note
When no signal inputs,  z mark will appear.
Using the D.ZOOM button
This function allows you to enter to the Digital zoom 
+/– mode.
 button
Press  button on the remote 
control.
Note
For details, see "Screen" of Main menu. ( zÆpage 60) 
Using the LENS SHIFT button
This function allows you to position the screen to the 
desired point without having picture distortion.
 button
Press  button on the 
remote control to display [Lens shift] on 
the screen.
Note
For details, please refer to “Adjusting the image”.   z
(Æpage 41)
Press and hold the  button or   z
button for more than 5 seconds, the lens shift will be 
return to the center position. 
						

							Basic operations by using the remote control
ENGLISH - 45
Basic Operation
Using the KEYSTONE button
This function allows you to correct keystone distortion.
 button
For EW530 series and EX500  J
series.
Press the  button on the remote 
control. The Keystone dialog box appears. Press 
▲▼ to correct keystone distortion. The keystone 
adjustment can be stored (Æpage 60).
OperationScreen image
Reduce the 
upper width 
with press 
▲.
Reduce the 
lower width 
with press 
▼.
For EZ570 series, EW630 series  J
and EX600 series.
Press the  button on the remote control 
to switch the [Standard] (for Vertical/Horizontal) /
[Corner correction] adjustment. The [Standard] or 
[Corner correction] adjustment dialog box appears. 
Press ▲▼◄► to correct the Standard or Corner 
distortion. The [Standard] or [Corner correction] 
adjustment can be stored. (Æpage 60)
Standard J
Corner correction J
Press the  button on the remote control 
to switch [Corner correction] adjustment, press the 
 button on the remote control to select the 
corner you want to adjust.
The top left corner adjustment as an example:
Note
The white arrows indicate that there is no correction. z
A red arrow indicates the direction of correction. z
An arrow disappears at the maximum correction. z
If you press and hold the  button for  z
3 seconds or more , the keystone adjustment will be 
canceled (Æpage 60).
The adjustable range is limited depending on the input  z
signal.
[Standard] and [Corner correction] functions cannot  z
be adjusted at the same time. If one of the functions 
is adjusted, and then the other one will be reset 
automatically. 
Reduce the lower width 
with press ▼.  
Reduce the upper width 
with press ▲.  
Reduce the right part 
with press ►.  
Reduce the left part 
with press ◄.  
Press ► 
Press ▼ 
Reduce the top 
left corner part 
with press ►▼. 
Reduce the top 
right corner part 
with press ◄▼.  
Reduce the bottom 
left corner part with 
press ►▲. 
Reduce the bottom 
right corner part 
with press ◄▲. 
Press the 
 
button 
Press the 
 
button 
Press the 
 
button 
Press the 
 
button  
						

							Basic operations by using the remote control
46 - ENGLISH
Basic Operation
Using the ZOOM +/- buttons
Adjusts the zoom of the lens.
 buttons
Press  buttons on the remote 
control.
Note
For details, please refer to “Adjusting the image”  z
(Æpage 41).
Using the FOCUS  +/- buttons
This function allows you to to adjust focus of the 
image.
 buttons
Press  buttons on the remote 
control.
Note
For details, please refer to “Adjusting the image”  z
(Æpage 41).
Using the INFO button
This function allows you to display the information 
menu.
 button
Press  button on the remote 
control.
Note
For details, see “Input Source Information Display ” in  z
“Information” under Main menu (Æpage 72).
Using the P IN P button
Only for EZ570 series, EW630 series and EW530 
series. 
This function allows you to operate the Picture in 
Picture function.
 button
Press  button on the remote 
control.
Note
For details, see “ zPicture in Picture” of "Setting" under 
Main menu (Æpage 65).  
						

							ENGLISH - 47
Settings
Menu Navigation
Navigating through the menu
Operating procedure J
For example: PT-EZ570U
Press the  button.1 ) 
The Main Menu screen appears.
Press ▲▼ to select the Main Menu 2 ) 
item.
Select the desired item from the 9 items: [Input], 
[PC adjust], [Image select], [Image adjust], 
[Screen], [Sound], [Setting], [Information] and 
[Network]. The selected item is highlighted with an 
orange cursor and the submenu of the selected 
item appears on the right.
Press ► or the  button.3 ) 
The submenu appears so that you can select the 
sub-menu item.
Press ▲▼ to select the desired sub-4 ) 
menu item.
Press the button or press ► 5 ) 
to enter the desired item.
Press ▲▼ ◄► to set or adjust the 6 ) 
parameter values.
Press ◄ to return the previous menu. 7 ) 
Press the  button to exit the 
menu display.
Note
Some items may not be adjusted or used for certain  z
signal formats input to the projector. The MENU items 
that cannot be adjusted or used are shown in gray 
characters, and they cannot be selected.
Some items can be adjusted even if signals are not input. z
See page 48 and 49 for details on the items of sub-menu. z 
						

							Menu Navigation
48 - ENGLISH
Settings
Main menu
The main menu consists of the following 9 menu 
items.
When a main menu item is selected, the screen 
changes to a submenu selection screen.
Input
PC adjust
Image select
Image adjust
Screen
Sound
Setting
Information
Network
Sub menu
The sub-menu screen of the selected main menu 
appears, and you can set and adjust the various items 
in the submenu.
Input [  J ]
Sub-menu itemFactory defaultPage
Input 1RGB(PC analog)50
Input 2Video50
Input 3Video50
 JPC adjust [  ]
Sub-menu itemFactory defaultPage
Auto PC adj.-  52
Fine sync.-  53
Total dots-  53
Position H-  53
Position V-  53
Sub-menu itemFactory defaultPage
Current mode- 54
Clamp- 54
Display area H- 54
Display area V- 54
Reset - 54
Mode free- 54
Store - 54
Note
This function will be available when the input source   z
come from computer.
 JImage select [  ]
Sub-menu itemFactory defaultPage
Dynamic-55
Standard- 55
Real- 55
Cinema*1- 55
Natural*1- 55
Image 1-10-55
When input video signal to the projector, these *1 : 
functions will be available.
 JImage adjust [  ]
Sub-menu itemFactory defaultPage
Contrast3256
Brightness3256
Color*13256
Tint*13256
Iris*2- 57
Color temp.Mid57
Red3257
Green3257
Blue3257
Offset3257
Daylight ViewAuto57
Sharpness*3858
Gamma858
Noise Reduction*1On58
Progressive*1On58
Reset-58
Store-58
When input video signal to the projector, these *1 : 
functions will be available.
EZ570 series, EW630 series and EX600 series Only.*2 : 
When input computer signal, the factory default of *3 : 
[Sharpness] is 8. When input video signal, the factory 
default of [Sharpness] is 15. 
						

							Menu Navigation
ENGLISH - 49
Settings
Screen [  J ]
Sub-menu itemFactory defaultPage
Normal - 59
Full - 59
Wide (16:9)- 59
Zoom- 59
True*1- 59
Natural wide*2-59
Custom- 59
Custom adj.- 60
Digital zoom + *1- 60
Digital zoom - *1- 60
KeystoneStore 60
CeilingOff 61
RearOff 61
Screen aspect*2Default(16:10)61
Reset- 61
When input computer signal to the projector, these *1 : 
functions will be available.
This function is not available for EX600 series and *2 : 
EX500 series.
Sound [  J ]
Sub-menu itemFactory defaultPage
Volume1562
Built-in SPOn62
MuteOff62
Setting [  J ]
Sub-menu itemFactory defaultPage
LanguageEnglish63
MenuCenter63
Input buttonMode 263
DisplayOn64
BackgroundBlue64
Logo-64
Picture in Picture*1Off65
HDMI setup- 66
DVI signal level-66
Lamp powerAuto66
Fan controlOff66
Simple modeOff67
Remote controlAll67
RC sensorFront & Back67
ECO management-67
Power managementShut down68
Standby modeNormal68
Direct onOff68
Sub-menu itemFactory defaultPage
P-timerCount up68
Security-69
Shutter*2Off69
Closed captionOff70
Video delay controlOff70
Filter counterOff71
Test patternColor71
Factory default-71
This function is not available for EX600 series and *1 : 
EX500 series. 
This function is not available for EW530 series and *2 : 
EX500 series.
Information [  J ]
Sub-menu itemFactory defaultPage
Input-72
System-72
H-sync freq.-72
V-sync freq.-72
Screen-72
Language-72
Lamp power-72
Lamp runtime-72
Filter counter-72
Power management-72
Key lock-72
PIN code lock-72
Shutter management-72
Simple mode-72
Remote control-72
Serial number-72
 JNetwork [  ]
Sub-menu itemFactory defaultPage
Projector name-73
Network setup-73
Network control-73
Network status-74
Network factory default-74 
						

							50 - ENGLISH
Settings
Input menu
Select [Input] from the Main Menu (see 
“Navigating through the menu” on page 47), 
then select the item from the sub-menu.
Input 1
Press ▲▼ to select [Input 1]. 1 ) 
Press ► to access the submenu.2 ) 
Press ▲▼ to select [RGB(PC analog)], 3 ) 
[RGB(Scart)], [DVI-D], [DVI-D(HDCP)] 
or [HDMI].
Press the  button.4 ) 
 JComputer System Selection
This projector automatically tunes to various types 
of computers with its Multi-scan system and Auto 
PC Adjustment. If a computer is selected as a signal 
source, this projector automatically detects the signal 
format and tunes to project a proper image without 
any additional settings. (Signal formats provided in 
this projector are shown on pages 109 -113.)
      When the projector cannot recognize the                                                                                                                                              
                connected signal conforming to the                         
               provided PC Systems, Auto is displayed  
               on the System Menu box and the Auto PC  
              adjustment function works to display proper  
               images.  If the image is not projected   
               properly, a manual adjustment is required.
                There is no signal input from the computer.                                                                                                                                        
                Check the connection between your                                                                                                                                             
                computer and the projector.
                The preset system is manually adjusted in                                                                                                                                               
                the PC adjust Menu. The adjusted data can                                                                                                                                              
                be stored in Mode 1-10. 
                PC Systems provided in this projector                                                                                                                                        
                is chosen. The projector chooses a proper                                                                                                                                           
                system provided in the projector and                                                                                                                                              
                displays it.
* Mode 1 and SVGA 1 are examples.  
Press ▲▼ to select [System].1 ) 
Press ► or the  button to 2 ) 
access the submenu.
Press ▲▼ to select the desired system.3 ) 
Input 2
Press ▲▼ to select [Input 2].1 ) 
Press ► to access the submenu.2 ) 
Press ▲▼ to select [Video], [Y, Pb/3 ) 
Cb,Pr/Cr], or [RGB].
Press the  button.4 ) 
Input 3
Press ▲▼ to select [Input 3].1 ) 
Press ► to access the submenu.2 ) 
Press ▲▼ to select [Video], [Y, Pb/3 ) 
Cb,Pr/Cr], or [S-video].
Press the  button.4 ) 
 JVideo System Selection
Video or S-video
Auto
The projector automatically detects an incoming video 
system, and adjusts itself to optimize its performance.
When Video System is [PAL-M] or [PAL-N], select the 
system manually.
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N
If the projector cannot reproduce proper video image, 
select a specific broadcast signal format from among 
[PAL], [SECAM], [NTSC], [NTSC 4.43], [PAL-M] and 
[PAL-N].
Auto
- - - -
Mode 1
SVGA 1
Remote ControlSide Control