Panasonic Projector Pt Ez570u Operating Instructions

							Network
ENGLISH - 81
Settings
Network config page  J
You can change network settings on projector when connecting with the administrator authority.
LAN settings z 
Click [Detailed set up] in the menu.1 ) 
Click [Change] to change the LAN settings.2 ) 
  zTo return to the previous window, click [Back].
Complete the detailed settings and  3 ) 
click [Next].
 
When [Next] is clicked, the next page appears, enabling   z
you to complete the detailed settings as desired.  
Settings performed here are the same as the  
settings performed with the [Network] menu of  
the projector.
Click [Submit].4 ) 
  zThe settings will be registered.
Note
Changing the setting of LAN while connected with LAN might disconnect the connection. z 
						

							Network
82 - ENGLISH
Settings
Ping test page  J
This page makes it possible to check whether the network is connected to the e-mail server, POP server, DNS 
server, etc.
Click [Detailed set up], then [Ping test] to display the Ping test page.
Display which appears when the connection
was successful.
Display which appears when the connection
failed.
1 Enter the IP address of the server to be tested.
2 Button for conducting the test.
2
1
ECO management set up page  J
This page makes it possible to set the savings of power consumption.
Click [Detailed set up], then [Eco management set up] to display the ECO management set up page.
Click [Submit] to execute the items you have set.
1 Set the brightness of the screen.
2 Set the conditions of the AUTO POWER SAVE.
3 Set the time of the countdown when no signal input.
1
2
3 
						

							Network
ENGLISH - 83
Settings
E-mail set up page  J
With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be 
sent to one or more preset e-mail addresses (maximum two addresses).
Click [Detailed set up], then [E-mail set up] to display the E-mail setup page.
1 Select Enable to use the e-mail function.
2 Enter the IP address or server name of the 
e-mail server (SMTP). The DNS server must be 
set if the server name is entered.
3 Enter the e-mail address of the projector. 
(maximum 63 characters)
4 The user can enter the location of, for 
example, the installed projector so that the 
recipient may easily identify the originator of 
the e-mail. 
(maximum 63 characters)
5 The user can modify the minimum time 
interval of temperature warning mail. The 
default value is 60 minutes. In this case, the 
user cannot send another mail for 60 minutes 
after sending previous temperature warning 
mail even the set warning temperature is 
reached again.
6 Select the temperature of the intake sensor at 
which to send a warning message.
1 Enter the E-mail Address1 of your desired recipient.
2 Select the conditions for sending e-mail.
    MAIL CONTENTS:Select [NORMAL] or [SIMPLE].
ERROR:An error is detected by self-diagnosis.
LAMP RUNTIME:Remaining lamp service time has reached the value set in the field.
INTAKE AIR TEMPERATURE:Intake air temperature has reached the value set in the field.
6
5
4
3
2
1
2
1 
						

							Network
84 - ENGLISH
Settings
E-mail set up page (continued) J
1 Enter the E-mail Address2 of your desired recipient.
2 Select the conditions for sending e-mail.
    MAIL CONTENTS:Select [NORMAL] or [SIMPLE].
ERROR:An error is detected by self-diagnosis.
LAMP RUNTIME:Remaining lamp service time has reached the value set in the field.
INTAKE AIR TEMPERATURE:Intake air temperature has reached the value set in the field.
Authentication set up page  J
The POP/SMTP server is set on this page when POP/SMTP authentication is required for mail transmissions.
Click [Detailed set up], then [Authentication set up] to display the Authentication server setup page.
1 Select the authentication method specified by 
your Internet service provider.
2 Set this if SMTP authentication has been 
selected.
3 POP server name field 
Available input characters: 
Alphanumeric characters (A - Z, a - z, 0 - 9), 
hyphen (-), period (.)
4 POP/SMTP server user name field
5 POP/SMTP server password field
6 Enter the port number for the SMTP server 
(normally “25”).
7 Enter the port number for the POP server 
(normally “110”).
8 Button to update settings
2
1
1
2
3
4
5
6
7
8 
						

							Network
ENGLISH - 85
Settings
Contents of mail sent  J
Mail with the contents shown below is sent when the e-mail settings have  z
been established.
=== Panasonic projector report(CONFIGURE) ===Projector Ty pe          : PT-EZ570Serial No               : 000000000-----  E-mail setup data -----TEMPER ATURE WARNING SETUP MINIMUM TIME            at [ 60] minutes interval INTAKE AIR TEMPER ATURE  Over [ 32degC / 89degF ] 
ERROR                   [ OFF ] LA MP RUNTIME            [ OFF ]   at REM AIN [ 400] H LA MP RUNTIME            [ OFF ]   at REM AIN [ 200] H INTAKE AIR TEMPER ATURE  [ OFF ] 
-----  check system -----M AIN CPU BUS                   [   OK   ]FAN                            [   OK   ]INTAKE AIR TEMPER ATURE         [   OK   ]AROUND LA MP TEMPER ATURE        [   OK   ]OPTICS MODULE TEMPER ATURE      [   OK   ]LA MP REM AIN TIME               [   OK   ]LA MP STATUS                    [   OK   ]APERTURS(CONTR AST-SHUTTER)     [   OK   ]SHUTTER                        [   OK   ]AIR FILTER                     [   OK   ]FILTER UNIT                    [   OK   ]
(Error code 00 00 00 00 00 00 00 00)
Intake air temperature     :[ 31 degC /  87 degF ]AROUND LA MP temperature    :[ 37 degC /  98 degF ]Optics module temperature  :[ 39 degC / 102 degF ]
PROJECTOR RUNTIME        1 H
LA MP  ECO              500 HLA MP  NOR M AL           300 HLA MP  REM AIN          2400 H
-------- Current status ---------M AIN VERSION         1.00NETWORK VERSION      1.00LA MP STATUS          LA MP=ONINPUT                RGBSIGNAL NA ME          XGA6SIGNAL FREQUENCY     0.00kHz / 0.00Hz
----- Wired Network configuration -----DHCP Client  OFF IP address   192.168.10.100M AC address  04:20:9A:00:00:00
----- Memo ----- 
						

							Network
86 - ENGLISH
Settings
Mail with the contents shown below is sent when an error has occurred. z
=== Panasonic projector report(ERROR) ===
Projector Ty pe          : PT-EZ570
Serial No               : 000000000
-----  check system -----
M AIN CPU BUS                   [   OK   ]
FAN                            [   OK   ]
INTAKE AIR TEMPER ATURE  
       [   OK   ]
AROUND LA MP TEMPER ATURE        [   OK   ]
OPTICS MODULE TEMPER ATURE      [   OK   ]
LA MP REM AIN TIME               [   OK   ]
LA MP STATUS                    [ FAILED ]
APERTURS(CONTR AST-SHUTTER)     [   OK   ]
SHUTTER                        [   OK   ]
AIR FILTER                 
    [   OK   ]
FILTER UNIT                    [   OK   ]
(Error code 00 40 00 00 00 00 00 08)
Intake air temperature     :[ 31 degC /  87 degF ]
AROUND LA MP temperature    :[ 37 degC /  98 degF ]
Optics module temperature  :[ 39 degC / 102 degF ]
PROJECTOR RUNTIME        1 H
LA MP  ECO              500 H
LA MP  NOR M AL           300 H
LA MP  REM AIN          2400 H
-------- Current status ---------
M AIN VERSION         1.00 
NETWORK VERSION      1.00 
LA MP STATUS          LA MP=OFF
INPUT                NETWORK
----- Wired Network configuration -----
DHCP Client  OFF 
IP address   192.168.10.100
M AC address  04:20:9A:00:00:00
----- Memo -----
Command port set up page  J
Set the port number to be used with command control.
Click [Detailed set up] → [Command port set up].
1  Input the port number to be used with command control
2 Setting update button
1
2 
						

							Network
ENGLISH - 87
Settings
Change Password page  J
Click [Change password].
1 Administrator
2 User
Administrator mode
1 Account
2 Current user name input field
3 Current password input field
4 New user name input field
5 New password input field
6 New password input field (re- enter for 
confirmation)
7 Button for executing password change
User account
1 Account
2 New user name input field
3 New password input field
4 New password input field (re- enter for 
confirmation)
5 Button for executing password change
User mode
A user can change password only.
1 Current password input field
2 New password input field
3 New password input field (re- enter for 
confirmation)
4 Button for executing password change
Note
When changing the administrator account, both “Current user name” and “Current password” are required. z
No account is not available . z
Administrator account and user account should be differed. z
2
1
7
65
4
3
2
1
5
4
3
2
1
4
3
2
1 
						

							Network
88 - ENGLISH
Settings
CRSTRON RoomView page  J
You can monitor or control the projector using RoomView.
To display the operation page of RoomView from Web Control screen, access with the administrator rights is 
required. (The [CRESTRON RoomView] button is not displayed on the Web Control screen for user rights.)
When you click [CRESTRON RoomView], the RoomView operation page is displayed.
If Adobe Flash Player is not installed in your computer, or if the browser does not support Flash, this page does 
not appear. In this case, return to the previous page by clicking [Back] in the operation page.
Operation page
1 Logout, Tools, Info, Help
    Exit the page when the password has changed and 
switches the pages for tools, information, help using  
the tab.
2 POWER
    Switches between on and off of the power.
3 VOL DOWN, AV MUTE, VOL UP
    Sets the volume, AV mute. When the power of the 
projector is turned off, VOL DOWN, AV MUTE and  
VOL UP are not available.
4 Input Select
    Sets the input selection. When the power of the 
projector is turned off, this operation is not available.
5 Operation buttons on the menu screen
    Operates on the menu screen.
6 Freeze, image quality adjustment
    Sets freeze, image quality details.
7 Back
    Returns to the previous page.
Tools page
Click Tools on the operation page.
1 Control system
    Sets the information required for the communication  
with the controller that is connected to the projector.
2 User Password
    Sets the password for the user rights in the operation 
page of RoomView.
3 Admin Password
    Sets the password for the administrator rights in the 
operation page of RoomView.
4 Network status
    Displays the setting of wired LAN.
    DHCP: Displays the value in the current setting.
    IpAddres: Displays the value in the current setting.
    SubnetMask: Displays the value in the current setting.
    DefaultGateway: Displays the value in the current setting.
    DNSServer: Displays the value in the current setting.
5 Exit
    Return to the operation page.
1
2
3
4
5
6
7
1
2
3
4
5 
						

							Network
ENGLISH - 89
Settings
Info page
Click Info on the operation page.
1 Projector name
    Displays the name of the projector.
2 Mac Address
    Displays the MAC address.
3 Resolution
    Displays the resolution of the projector.
4 Lamp Hours
    Displays the lamp usage time (converted value).
5 Power Status
    Displays the status of the power.
6 Source
    Displays the selected video input.
7 Projector Position
    Displays the projection method of the projector.
8 Lamp Mode
    Displays the lamp mode.
9 Error Status
    Displays the error status.
10  Exit
     Return the operation page.
User mode
A user can change password only.
1  Help Desk
    Sends or receive messages to the adminidtrator who 
uses Crestron RoomView.
1
2
4
3
5
6
7
8
9
10
1 
						

							90 - ENGLISH
Maintenance
About indicator status
If an indicator turns on
If a problem occurs within the projector, it will be notified with the temperature indicator , the filter 
indicator , the shutter indicator *, and the lamp indicator .
Check the status of the indicators and take the following action.
* (Only for EZ570 series, EW630 series and EX600 series.)
CAUTION
Before you take a remedial measure, follow the procedure of switching the power off indicated in “Turning off the projector”.  z
(Æpage 40)
If multiple indicators light or blink, verify the status of the projecto\
r by looking at each indicator. z
Note
Confirm the status of the power indicated on the  indicator. z
When operating correctly J
The status of the indicator is displayed with the following symbols.
: Off, : On, : Flashing, „: Off or On or Flashing
Indicators
Status of the projectorGreen/Red/Orange

Red
 Orange

Blue

Orange
//The power plug has been removed from the 
outlet.
//„*1„*1„*1„*1
The projector is in the standby mode.
Turns on when pressing the  
button on the remote control or the  button on the side control.
//„*1„*1„*1„*1The projector is operating normally.
//*2„*1„*1„*1„*1
The lamp is cooling down. The projector does 
not turn on when pressing the  
button on the remote control or the  button on the side control until the standby indicator 
 changes to red.
*2//„*1„*1„*1„*1The projector is in the power management 
mode. The lamp will turn on when controlling the 
projector, allowing the user to start operating it.
//*2„*1„*1„*1„*1Power management mode is [On] and the lamp 
is cooling down.
//„*1„*1„*1The shutter function has been turned on.
Press any button on the remote control or the 
side control to cancel the function.
//„*1„*1*2„*1The projector is in the shutter management 
mode. The lamp will turn on when controlling the 
projector, allowing the user to start operating it.
//*2„*1„*1*2„*1Shutter management mode is [On] and the lamp 
is cooling down.
*1: The indicator will change according to different conditions, regardless of the status of other indicators.
*2: The indicator will flash in approximately 1-second intervals.