Panasonic Projector Pt Ez570u Operating Instructions

							Screen 
ENGLISH - 61
Settings
Ceiling
This function is used to project the image from a 
ceiling-mounted projector.
Press ▲▼ to select [Ceiling] and then 1 ) 
press the  button.
Press ▲▼ to change the image.2 ) 
When this function is set to [On], the picture will  z
be top/bottom and left/right reversed.
Rear
This function is used to project the image from rear of 
the screen.
Press ▲▼ to select [Rear] and then 1 ) 
press the  button.
Press ▲▼ to change the image.2 ) 
When this function is set to [On], the picture will  z
be left/right reversed.
Screen aspect
This function is used to project the image to a 4:3 or 
16:9 projection screen.
Press ▲▼ to select [Screen aspect1 ) *] 
and then press the  button.
Press ▲▼ to choose one from the 2 ) 
items as below.
* This function is not available for EX600 series, EX500 
series.
Default(16:10)16:10 is the aspect of the LCD 
panel.
16:9Set to a 16:9 projection screen. 
4:3Set to a 4:3 projection screen.
Note
When the [4:3] function is selected, [Natural wide] is not  z
available in the AV screen.
When the [16:9] function is selected, [Wide (16:9)] is not  z
available in the AV screen.
Reset
To reset the adjusted data, all adjustments will return 
to their previous figures.
Press ▲▼ to select [Reset] and then 
press the  button.
A confirmation box appears and then select  z
[Yes]. 
						

							62 - ENGLISH
Settings
Sound
Select [Sound] from the Main Menu (see 
“Navigating through the menu” on page 47), 
then select the item from the sub-menu.
Remote ControlSide Control
Volume
Press ▲▼ to select [Volume] and then 1 ) 
press the  button.
Press ◄► to adjust the volume.2 ) 
Press  button to set the volume. z
OperationAdjustmentAdjustment 
range
Press ►.turn up the 
volume
Maximum 
value 63
Press ◄.turn down the 
volume
Minimum 
value 0
You can also press  (+/-) buttons on  z
the remote control or side control to adjust the 
volume.
Built-in SP
Press ▲▼ to select [Built-in SP] and 1 ) 
then press the  button.
Press ▲▼ to switch the [Built-in SP] 2 ) 
function between [On] and [Off].
OffWhen the Built-in SP sound is 
turned off
On[Mute] is cancelled
Mute
Press ▲▼ to select [Mute].1 ) 
Press the  button to switch 2 ) 
the mute function between [On] and 
[Off].
Press the  button on the remote  z
control to temporarily turn off the sound. To turn 
the sound back on, press the  button 
again or press the  (+/–) buttons. 
						

							ENGLISH - 63
Settings
Setting
Select [Setting] from the Main Menu (see 
“Navigating through the menu” on page 47), 
then select the item from the sub-menu.
Remote ControlSide Control
Language
Press ▲▼ to select [Language].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to select the desired 3 ) 
language.
             For example: PT-EZ570U
The language used in the On-Screen Menu is  z
available in English, German, French, Italian, 
Spanish, Portuguese, Russian, Chinese, Korean,  
and Japanese.
Menu/Menu position
  [Menu] function is only for EZ570 series.
  [Menu position] function is only for EW630 series, 
EW530 series, EX600 series and EX500 series.
Position J
This function is used to change the position of the On-
Screen Menu.
Press ▲▼ to select [Position].1 ) 
Press the  button to change 2 ) 
the position.
The Position changes each time you press  z
 button as follows:
the center → the bottom left → the bottom right → the 
top left → the top right → the center.......
Menu size J*1
This function is used to change the display size of the 
On-Screen Menu.
Press ▲▼ to select [Menu size] and 1 ) 
press the  button.
Press ▲▼ to switch the [Menu size] 2 ) 
function between [Normal] and 
[Double].
NormalDisplay the On-Screen Menu on the 
screen in its normal size.
DoubleDisplay the On-Screen Menu on the 
screen in its double normal size.
This function is only for EZ570 series*1 : .
Input button
This function detects the input signal automatically. 
When a signal is found, the search will stop.
Press ▲▼ to select [Input button].1 ) 
Press the  button.2 ) 
Press ▲▼ to select these functions as 3 ) 
follows:
Mode 1Input search will not work*1
Mode 2Input search works*2
Mode 3Input search works*3
Input search will not work.*1 : Input search works under the following situation: *2 : ●   When pressing the  button on the remote control or on the side control.Input search works under the following situation: *3 : ● When turning on the projector by pressing the                                                                                                                                                   button on the remote control                                                                                                                                          
    or the button on the side control.●●●●●                                                                        \
                                                           ● When pressing the  button on the remote    control or the side control.                                                               
● When no signal is detected. 
						

							Setting
64 - ENGLISH
Settings
Display
This function decides whether to display On-Screen 
Displays.
Press ▲▼ to select [Display].1 ) 
Press the  button.2 ) 
Press ▲▼ to switch3 )  between each 
option as below.
OnShow all the On-Screen 
displays *1
Countdown 
off
Show the input image instead 
of the countdown when turning 
on the projector *2
OffHide the On-Screen Displays *3
Use this function when you want to project *1 : 
images after the lamp becomes bright enough. 
The factory default setting is in this option.
Use this function when you want to project the *2 : 
image as early as possible even when the lamp 
is not bright enough. 
Hide the On-Screen Displays except;  *3 : 
● On-Screen Menu. 
● [Power off?]  
● [P-timer] display. 
● No signal for [Power management]   
● [Please wait ...]  
● [Picture in Picture]  
● [Simple mode]  
● [Video delay control]  
● Arrows for the [True] function in the Screen                                                                                                                                           
   Menu.  
●  [Iris] function is disabled.
Background
Select the background screen for when no input signal 
is detected.
Press ▲▼ to select [Background].1 ) 
Press the  button.2 ) 
Press ▲▼ to switch3 )  between each 
option as below.
BlueBlue colored background.
UserThe logo transferred by "Logo
Transfer Software *1 " is projected.
BlackBlack colored background.
" Logo Transfer Software" is included on the *1 : 
supplied CD-ROM.
Logo
This function allows you to customize the screen logo 
with [Logo select], [Logo PIN code lock] and [Logo 
PIN code change] functions.
Press ▲▼ to select [Logo].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to choose the desired item.3 ) 
Logo select J
This function decides on the starting-up display from 
among following options.
OffShow the countdown display only.
DefaultShow the factory-set logo.
UserThe logo transferred by "Logo
Transfer Software *1 " is projected.
" Logo Transfer Software" is included on the *1 : 
supplied CD-ROM.
Logo PIN code lock J
This function prevents an unauthorized person from 
changing the screen logo.
OffThe screen logo can be changed freely 
from the Logo Menu.
OnThe screen logo cannot be changed 
without a Logo PIN code.
Note
If you want to change the Logo PIN code lock setting,  z
press the  button and the Logo PIN code 
dialog box appears. Enter a Logo PIN code by following 
the steps below. The initial Logo PIN code is set to “4321” 
at the factory.
Logo PIN code change J
Logo PIN code can be changed to your desired four-
digit number.
Press ▲▼ to select [Logo PIN code 1 ) 
change] and press the  
button.
Current logo PIN code dialog box appears. z
Press ▲▼ to enter the current code, 2 ) 
press the ► button to fix the number 
and move the red frame pointer to the 
next box.
The New Logo PIN code input dialog box  z
appears.
Repeat this step to set the new Logo 3 ) 
PIN code. 
						

							Setting
ENGLISH - 65
Settings
Attention
Be sure to note the new Logo PIN code and keep it on  z
hand. If you lost the number, you could no longer change 
the Logo PIN code setting.
Picture in Picture
This function is used to project two images 
simultaneously by placing a separate small sub 
screen within or next to the main screen.
Press ▲▼ to select [Picture in 1 ) 
Picture*].
You can also press the button on  z
the remote control for more than 3 seconds to 
display [Picture in Picture] menu.
Press the  button to access 2 ) 
the submenu.
Only the sound from the source of Main picture  z
is valid, while the source of Sub picture cannot 
output the sound.
* (Only for EZ570 series, EW630 series and EW530 
series.) 
User setting J
Show the selected mode ([Off/User 1-5]) and its status 
([Stored /Free/ Adj.]). [User 1] and [User 2] have 
stored default values.
P in P/P by P J
P IN PProvide the images of Main picture 
and Sub picture at the ratio of 
Screen aspect in the Screen Menu.
P by PProvide the images of Main picture 
and Sub picture at the ratio of 4:3.
Note
In [P in P] the larger picture is main picture, and the  z
smaller one is sub picture; in [P by P], the left picture is 
main picture, and the right one is sub picture.
Main picture/ Sub picture J
Press ▲▼◄► to adjust the display 1 ) 
position of active frame indicated in 
white.
The frame will disappear after 10 seconds or  z
when the  button is pressed.
InputSelect an input from Input 1-3.
SourceSelect an input source.
SizeSelect the display size.
PositionPress the  button at 
Position and the display position 
setting screen appears.
Selecting the Main picture or the Sub picture z
     During Picture in Picture mode, and being 
undisplayed On Screen Menu, press the  
button to select Main or Sub picture. (A red frame 
will be displayed on the selected picture.)
Switching Input and Source z
     When selecting Main picture or Sub picture, input 
and source can be set by pressing the  
button on the side control or INPUT 1/2/3 button 
on the remote control. Operation on the On Screen 
Menu is not necessary.
Frame lock J
Set the Frame Lock to Main picture or Sub picture.
Reset J
Press the  button at [Reset] to display a 
confirmation box. To reset, press the  button 
at [Yes].
Mode free J
Delete the data stored in the Mode and return to [Free]. 
Use the ▲▼ buttons to select [Mode free] and press 
the  button to show the [Where to free?] 
dialog box. Move the highlight to one of the mode 
([User 1 - 5]) which you want to delete and press the 
 button. Then the confirmation box appears. 
To delete, select [Yes].
Store J
Store the adjusted data in the [User 1-5]. Use the 
▲▼ buttons to select [Store] and press the  
button to show the [Where to store?] dialog box. Move 
the highlight to one of the mode (User 1 - 5) which 
you want to store and press the  button. 
Then the confirmation box appears. To store adjusted 
data, select [Yes].
Note
The [Picture in Picture] function is not available  z
depending on the input signals and the selected input 
terminals.
When the input signal(s) is/are incompatible,  zX mark will 
be displayed on the Main/Sub picture. 
						

							Setting
66 - ENGLISH
Settings
HDMI setup
This function is only used for HDMI input source.
Press ▲▼ to select [HDMI setup].1 ) 
Press ► or the  button.2 ) 
The names for the output setting of Digital R/G/ z
B vary from equipment to equipment.
HDMI signal level J
64-940When the output of Digital R/G/B 
equipment is set to Standard.
0-1023When the output of Digital R/G/B 
equipment is set to Enhanced.
Sound J
HDMIWhen Digital input source is input,
Sound is set to HDMI.
AUDIO 1When DVI input source is changed 
to HDMI input source, Sound is set 
to AUDIO 1.
Note
For details, refer to the operating instructions of your  z
Digital R/G/B equipment.
DVI signal level
This function is only used for DVI-D input source.
Press ▲▼ to select [DVI signal level] 1 ) 
and then press the  button.
Press ▲▼ to switch the item.2 ) 
16-235When you want to enhance 
the weaken signal.
0-255:PCWhen in normal condition.
Lamp power
This function allows you to change brightness of the 
screen.
Press ▲▼ to select [Lamp power] and 1 ) 
then press the  button .
Press ▲▼ to select one among the 2 ) 
modes as below.
AutoBrightness according to the input 
signal. 
    NormalThe lamp power output is 
maximum.
Eco1The lamp power output is 80% 
of the Normal mode.
Eco2The lamp power output is 30% - 
80% of the Normal mode.
Fan control
Press ▲▼ to select [Fan control] and 1 ) 
then Press  button.
Press ▲▼ to select one among 2 ) 
options as below.
Choose the running speed of cooling fans from  z
the following options according to the ground 
elevation under which you use the projector.
OffNormal speed.*1
On 1Faster than [Off] mode.*2
On 2Faster than [On 1] mode.*3
Set this function to [Off] when using the projector *1 : 
in non-high altitude environment.
Select [On 1] when using the projector in high *2 : 
altitudes (about 1 000 ~ 2 000 meters or more 
above the sea level) where the fans have less 
cooling effect.
Select [On 2] when using the projector in higher *3 : 
altitudes (about 2 000 ~ 2 800 meters or more 
above the sea level) where the fans have lesser 
cooling effect.
Note
Failure to set the running speed of cooling fans  z
properly may affect the projector life.
The fan noise becomes louder in [On 1] and [On 2]. z 
						

							Setting
ENGLISH - 67
Settings
Simple mode
This function decides whether to activate the simple 
mode.
Press ▲▼ to select [Simple mode] and 1 ) 
then press the  button.
Press ▲▼ to switch between [On] and 2 ) 
[Off].
OnSimple mode function is off.
OffOnly the simple mode buttons 
are active.
Note
Warning icon and  z[Simple mode : On] message 
appear on the screen for about 4 seconds when 
press the button which is not the simple mode 
button.
Remote control
This switching function prevents remote control 
interference when operating several projectors or 
video equipment at the same time.
Press ▲▼ to select [Remote control].1 ) 
Press the  button.2 ) 
Press ▲▼ to select one among the 3 ) 
sixty and five codes. 
This projector provides 65 different remote  z
control codes: [All], [Code 01]~[Code 64].
Note
When operating the projector under [All] code, you can  z
operate several projectors at the same time. If you want 
to operate the projector independently, you must switch 
to other code.
When different codes are set on the projector and on the  z
remote control, any operation cannot be made. In that 
case, switch the code on the remote control to fit the 
code on the projector.
RC sensor
Select a location of the infrared remote receiver of the 
remote control.
Press ▲▼ to select [RC sensor].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to select one among 3 ) 
options as below.
AllActivate all of the receivers.
Front & 
Top
Activate both the front and top 
receivers.
Top & 
Back
Activate both the top and back 
receivers.
Front & 
Back
Activate both the front and back 
receivers.
FrontActivate only the front receiver.
TopActivate only the top receiver.
BackActivate only the back receiver.
Eco management
Can optimize lamp power and reduce the power 
consumption according to the application.
Press ▲▼ to select [Eco 1 ) 
management].
Press ► or the  button.2 ) 
Auto power save J
Press ▲▼ to select [Auto power save] 1 ) 
and press the button.
Press ▲▼ to choose [On] between 2 ) 
[On] and [Off].
Press ▲▼ to select auto power save 3 ) 
conditions.
Ambient light 
detection
Adjusts the lamp power according 
to the ambient brightness.
Signal 
detection
Drops the lamp power when no 
signal is input.
AV mute 
detection*1Drops the lamp power in the AV 
mute mode.
This function is only for EW530 series and *1 : 
EX500 series.
Note
When [Auto power save] is [Off], [Ambient light  z
detection], [Signal detection] and [AV mute detection] are 
not available. 
Only these buttons are active when the simple mode is set to [On]. [POWER ON, STANDBY, SHUTTER (AV MUTE), INPUT, MENU, AUTO PC ADJ, ▲, ▼ (MUTE), ◄ (VOLUME-), ► (VOLUME+), ENTER, IMAGE SELECT, IMAGE ADJUST, P-TIMER, ECO, SCREEN, P IN P, ON /OFF]. Number buttons also become active only when setting the remote control codes numbers or entering the PIN code numbers. 
						

							Setting
68 - ENGLISH
Settings
Power management
For reducing power consumption as well as 
maintaining the lamp life, the Power management 
function turns off the projection lamp when the 
projector is not operated for a certain period.
Press ▲▼ to select [Power 1 ) 
management].
Press ► or the  button to 2 ) 
access the submenu.
Mode J
Press ▲▼ and then press the 1 ) 
 button to select one mode 
among the items as below.
ReadyWhen the lamp has been fully cooled 
down, the  
indicator changes to green blinking. 
In this condition, the projection lamp 
will be turned on if the input signal 
is reconnected or any button on 
the side control or remote control is 
pressed.
Shut 
down
When the lamp has been fully cooled 
down, the power will be turned off.
Off[Power management] function is off.
Timer J
Press ▲▼ to select [Timer] and then 1 ) 
press the  button.
Press ▲▼ to set the Timer(1~30min).2 ) 
Standby mode
This function can set the electric power when the 
projector is standing by.
Press ▲▼ to select [Standby mode] 1 ) 
and then press the  button.
Press ▲▼ to switch between the items  2 ) 
as below.
NormalThe normal situation. 
EcoThe power less than 0.5W.
NetworkThe power less than Normal.
Note
When selecting [Network], the cooling fans may be  z
running depending on the temperature inside the 
projector even if the projector is turned off.
If [Standby mode] is set to [Eco], you cannot use network  z
functions when the projector is standing by. Also, you 
cannot use some RS-232C protocol commands.
If set to [Network], you can use network functions when  z
the projector is standing by.
Direct on
Press ▲▼ to select [Direct on] and 1 ) 
then press the  button.
Press ▲▼ to switch between [On] and 2 ) 
[Off].
When this function is set to [On], the projector  z
will be automatically turned on just by 
connecting the AC power cord to a wall outlet.
Be sure to turn off the projector properly. If the  z
projector is turned off in the incorrect sequence, 
the [Direct On] function does not work properly.
P-timer
This function allows you to change the setting of the 
P-timer and execute it.
Press ▲▼ to select [P-timer].1 ) 
Press ► or  button to access 2 ) 
the submenu.
Mode J
Press ▲▼ button to select one mode 1 ) 
among the items as below.
Count up
The P-timer display 000:00 
appears on the screen and the 
count up starts (000:00-180:00).
Count downThe time set in the Timer setting 
appears on the screen and the 
countdown starts.
Timer J
Press ▲▼ to select [Timer] and then 1 ) 
press the  button.
Press▲▼ to set the [Timer](1-180 Min).2 ) 
[Timer] is available in [Count down] only.  z
Factory default value is 10 Min. 
						

							Setting
ENGLISH - 69
Settings
Execute J
Press ▲▼ to select one among the 1 ) 
items as below and then press the 
 button. 
StartIt executes the count up or count 
down function.*1
ResetReset the P-timer values.*2
ExitTo exit the P-timer operation.
Press the  button at Start and the *1 : 
indication changes into Stop. To stop Count up or 
Count down, press the  button at Stop 
on the screen menu, then the indication changes 
into Restart. Press the  button at 
Restart to resume Count up or Count down.
Press the  button at Reset to return to *2 : 
the following value: 
Count up"000:00"
Count downTimer that you set
Attention
To stop the [P-timer] function, press the   z
button.
To cancel the [P-timer], press and hold the   z
button for a few seconds.
Security
This function allows you to use the [Key lock] and [PIN 
code lock] function to set the security for the projector 
operation.
Press ▲▼ to select [Security].1 ) 
Press ► or the  button to 2 ) 
access the submenu.
Key lock J
This function locks the side control and remote control 
buttons to prevent operation by unauthorized persons.
Press ▲▼ to select the desired items 1 ) 
as below.
Unlocked.
Lock the operation of the side 
control. To unlock, use the remote 
control.
Lock the operation of the remote 
control. To unlock, use the side 
control.
PIN code lock J
This function prevents the projector from being 
operated by unauthorized persons and provides the 
following setting options for security.
Press ▲▼ to select the desired items 1 ) 
as below.
OffUnlocked.
On 1Enter the PIN code every time 
turning on the projector.
On 2
Enter the PIN code to operate 
the projector once the power cord 
is disconnected; as long as the 
AC power cord is connected, the 
projector can be operated without 
a PIN code.
Attention
Whenever you change the PIN code lock setting or the  z
PIN code (the four-digit number), you are required to 
enter the PIN code. The "1234" is set as the initial PIN 
code at the factory.
PIN code change J
The PIN code can be changed to your desired four-
digit number.
Press ▲▼ to select [PIN code change] 1 ) 
and then press  button.
Current Pin code dialog box appears. z
Press ▲▼ to enter the current code. 2 ) 
Press ► button to fix the number and 
move the red frame pointer to the next 
box. 
The New PIN code input dialog box appears. z
Repeat these steps to set a new PIN 3 ) 
code.
Shutter
Shutter function is available to block out light to the 
screen, so that the screen can be used for the other 
presenters.
Press ▲▼ to select [Shutter1 ) *].
Press ► or the  button to 2 ) 
access the submenu.
* (Only for EZ570 series, EW630 series and EX600 
series.) 
Protection J
Prohibit the shutter operation from the remote control 
and the projector's side control. 
						

							Setting
70 - ENGLISH
Settings
Press ▲▼ to select the desired items 1 ) 
as below.
Permit the shutter operation from 
both the remote control and the 
projector's side control.
Prohibit the shutter operation 
from the remote control.
Prohibit the shutter operation 
from the side control.
Prohibit the shutter operation 
from both the remote control and 
the projector's side control.
Release key J
By using the Release key function from the following 
options, the Shutter can be released when it stays 
activated.
Any
By pressing any button on the 
projector's side control or the 
remote control, the shutter can 
be released when it is closed, 
and meanwhile the function of 
the selected item will come into 
effect.
Shutter
Only by pressing the 
 button on the 
projector’s side control or the 
remote control the shutter can be 
released when it is closed.*1
In addition, when the [Shutter] is functioning, *1 : 
only the following buttons are active:
 
 button and < z> button on the projector’s side control.
 buttons and  button on  z
the remote control. 
Management J
The Shutter Management function turns off the 
projection lamp when the projector is left with the 
shutter closed and the set time has passed away. 
The count-down time can be set between 5 and 480 
minutes. When the count-down time has elapsed, the 
shutter will be opened up automatically and the lamp 
will be turned off to cool itself down. The  
indicator is blinking blue during this cooling-off period. 
When the lamp has been fully cooled down, the 
 indicator turns green lighting 
and the  indicator keeps blinking. Should 
the  button be pressed in this condition, the 
projection lamp will be turned on and the  
indicator turns off.
Closed caption
[Only for NTSC, 480i input]
Press ▲▼ to select [Closed caption].1 ) 
Press ► or the  button to 2 ) 
enter the submenu.
Closed caption J
Press ▲▼ to select [Closed caption] 1 ) 
and then press the  button.
Press ▲▼ to select [Off], [CC1], [CC2], 2 ) 
[CC3] or [CC4].
Color J
Press ▲▼ to select [Color] and then 1 ) 
press the  button.
Press▲▼ to select color or white.2 ) 
Note
The closed caption is mainly used in the north America.  zThis function shows the text information contained in the image signal. Captions may not be displayed on some devices or software.You can select [Closed caption] when [NTSC] or [480i]  zsignals are input.Part of characters may not displayed when high  zcompensation values are set in [Keystone].Closed captions are not displayed while the menu screen  z
appears.
Video delay control
This function allows you to make a digital processing 
of a projected image faster.
Press ▲▼ to select [Video delay 1 ) 
control] and then press the  
button.
Press ▲▼ to select one item between 2 ) 
[Off], [Low], [Mid] and [High]*.





* When this function is for these models (EW530  
series and EX500 series), it only can switch 
between [On] and [Off].
Note
[Noise reduction] and [Progressive] cannot be selected  z
when [Video delay control] function is set to [On].The following functions are not available respectively  zwhen [Video delay control] is set to [Low]/[Mid]/[High].     Low ...[Keystone] cannot be selected.     Mid ...   [Progressive] and [Noise reduction] cannot be selected.     High ..  
[Keystone], [Progressive] and [Noise reduction] cannot be selected.When [Video delay control] function is set to [Low] or  z[High] and press the  button on the remote control, [Video delay :On] will be displayed on the bottom left screen.