Panasonic Projector Pt Ez570u Operating Instructions

							Input menu
ENGLISH - 51
Settings
Y, Pb/Cb, Pr/Cr
Auto
The projector automatically detects an incoming video 
signal, and adjusts itself to optimize its performance.
Y, Pb/Cb, Pr/Cr SIGNAL FORMAT
If the projector cannot reproduce proper video image, 
select a specific component video signal format 
among [480i], [576i], [480p], [576p], [720p], [1 035i]  
[1 080i] and [1 080p].
Press ▲▼ to select [System].1 ) 
Press ► or the  button to 2 ) 
access the submenu.
Press ▲▼ to select the desired system.3 ) 
Note
The AV System Menu cannot be selected when  z
selecting [RGB (Scart)]. 
						

							52 - ENGLISH
Settings
AUTO PC adjust
Select [PC adjust] from the Main Menu (see 
“Navigating through the menu” on page 47), 
then select the item from the sub-menu.
Remote ControlSide Control
Auto PC adj.
Auto PC adjustment function is provided to 
automatically adjust [Fine sync], [Total dots], [Position 
H] and [Position V] to conform to your computer.
Press ▲▼ to select [Auto PC adj.] and 
then press the  button. 
[Please wait...] z appears while the Auto PC 
adjustment is in process.
To store adjustment parameters
The adjusted parameters from the Auto PC adjustment 
can be stored in the projector. Once the parameters 
are stored, the setting can be done just by selecting a 
Mode (1–10) in the PC System Menu (see page 50). 
See also [Store] on page 54.
Attention
[Fine sync], [Total dots], [ zPosition H] and [Position 
V] of some computers cannot be fully adjusted with 
the Auto PC adjustment function. When the image 
is not provided properly with this operation, manual 
adjustments are required (Æpages 53-54). 
The Auto PC adjustment cannot be operated when  z
[480i], [576i], [480p], [576p], [720p], [1 035i] or  
[1 080i] is selected in the PC System Menu (Æpage 
50), or when the signal is coming from the HDMI or 
DVI-D terminal. 
						

							ENGLISH - 53
Settings
Manual PC adjust
Select [PC adjust] from the Main Menu (see 
“Navigating through the menu” on page 47), 
then select the item from the sub-menu.
Remote ControlSide Control
Some computers employ special signal formats 
which may not be tuned by Multi-scan system of this 
projector. Manual PC adjustment enables you to 
precisely adjust several parameters to match those 
signal formats. The projector has 10 independent 
memory areas to store those parameters manually 
adjusted. It allows you to recall the setting for a 
specific computer.
Fine sync
Press ▲▼ to select [Fine sync].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the value.3 ) 
The value can be adjusted from 0 to 31. z
Total dots
Press ▲▼ to select [Total dots].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the value.3 ) 
Position H
Press ▲▼ to select [Position H].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the horizontal 3 ) 
picture position.
For horizontal (right and left)  J
adjustment
OperationAdjustment
Press ◄.
The picture 
position 
moves to the 
right.
Press ►.
The picture 
position 
moves to the 
left.
Position V
Press ▲▼ to select [Position V].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the vertical picture 3 ) 
position.
For vertical (up and down)  J
adjustment
OperationAdjustment
Press ►.
The picture 
position 
moves up.
Press ◄.
The picture 
position 
moves down. 
						

							Manual PC adjust
54 - ENGLISH
Settings
Current mode
Press ▲▼ to select [Current mode].1 ) 
Press ► or the  button to 2 ) 
enter the next submenu to show 
[H-sync freq.] and [V-sync freq.] of the 
connected computer.
Clamp
Press ▲▼ to select [Clamp].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the clamp level.3 ) 
When the image has dark bars, try this  z
adjustment.
Display area H
Press ▲▼ to select [Display area H].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the horizontal area 3 ) 
displayed by this projector.
Display area V
Press ▲▼ to select [Display area V].1 ) 
Press the  button to display 2 ) 
the dialog box.
Press ◄► to adjust the vertical area 3 ) 
displayed by this projector.
Reset
To reset the adjusted data, all adjustments will return 
to their previous figures.
Press ▲▼ to select [Reset].1 ) 
Press the  button.2 ) 
A confirmation box appears and then select [Yes]. z 
Mode free
Press ▲▼ to select [Mode free].1 ) 
Press ► or the  button to 2 ) 
enter the next submenu.
Move the highlight to the mode that you want  z
to clear and then press the  button. A 
confirmation box appears and then select [Yes].
Store
Press ▲▼ to select [Store].1 ) 
Press ► or the  button to 2 ) 
enter the next submenu.
Move the highlight to one of the Modes 1 to 10  z
in which you want to store, and then press the 
 button. A confirmation box appears 
and then select [Yes]. 
						

							ENGLISH - 55
Settings
Image select 
Select [Image select] from the Main Menu (see 
“Navigating through the menu” on page 47), 
then select the item from the sub-menu.
Remote ControlSide Control
Dynamic
For viewing pictures in a bright room.
Press ▲▼ to select [Dynamic] and then 
press the  button.
Standard
Normal picture mode preset on the projector.
Press ▲▼ to select [Standard] and then 
press the  button.
Real
Picture mode with improved halftone for graphics. 
Press ▲▼ to select [Real] and then press 
the  button.
Cinema
Picture mode adjusted with fine tone.
Press ▲▼ to select [Cinema] and then 
press the  button.
Natural
Picture mode with improved halftone for graphics. 
Press ▲▼ to select [Natural] and then 
press the  button.
Image 1-10
For viewing with the user preset image mode in the 
Image adjust Menu. 
Press ▲▼ to select [Image 1-10] and then 
press the  button. 
						

							56 - ENGLISH
Settings
Select [Image adjust] from the Main Menu (see 
“Navigating through the menu” on page 47), 
then select the item from the sub-menu.
Remote ControlSide Control
Note
Make sure you selected [Store] after adjusting settings.  z
Some settings can not be stored if not registered with 
[Store] function.
Contrast
Press ▲▼ to select [Contrast].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.increase the contrastMaximum 
value 63
Press ◄.decrease the 
contrast
Minimum 
value 0
Brightness
Press ▲▼ to select [Brightness].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.increase the 
brightness
Maximum 
value 63
Press ◄.decrease the 
brightness
Minimum 
value 0
Color
Press ▲▼ to select [Color].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.increase the 
intensity of the color
Maximum 
value 63
Press ◄.decrease the 
intensity of the color
Minimum 
value 0
Note
When input video signal to the projector, [Color] will be  z
available.
Tint 
Press ▲▼ to select [Tint].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the tint value to 3 ) 
get a proper color balance.
Adjustments can be made between z 0 and 63.
Note
When you select [NTSC] or [NTSC4.43] in System menu  z
under Video input signal, [Tint] will be available.
Iris   
This iris function effectively increase the contrast 
intensity.
Press ▲▼ to select [Iris1 ) *].
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to select the desired items.3 ) 
OffDisabled
OnContrast is prioritized over 
brightness.
*  It is only for EZ570 series, EW630 series and EX600 
series.
Image adjust 
						

							Image adjust
ENGLISH - 57
Settings
Color temp.
Press ▲▼ to select [Color temp.].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to select the desired Color 3 ) 
temp. level.
You can select the desired [Color temp.] from  z
[XLow], [Low], [Mid] or [High].
Red 
Press ▲▼ to select [Red].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.deepen red toneMaximum 
value 63
Press ◄.lighten red toneMinimum 
value 0
Green
Press ▲▼ to select [Green].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.deepen green 
tone
Maximum 
value 63
Press ◄.lighten green 
tone
Minimum 
value 0
Blue 
Press ▲▼ to select [Blue].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.deepen blue toneMaximum 
value 63
Press ◄.lighten blue toneMinimum 
value 0
Offset
Press ▲▼ to select [Offset].1 ) 
Press ► or the  button to 2 ) 
access the submenu.
Press ▲▼ to select the desired item 3 ) 
and then press the  button.
Press ◄► to adjust the setting value.4 ) 
OperationAdjustmentAdjustment 
range
Press ►.
deepen  red/green/
blue tone of the 
black level of an 
image
Maximum 
value 63
Press ◄.
lighten red/green/
blue tone of the 
black level of an 
image
Minimum 
value 0
Daylight View
This function uses an ambient light sensor to detect 
the room’s light intensity and adjust the projector 
output automatically to ensure a bright presentation.
Press ▲▼ to select [Daylight View].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to switch between [Auto], 3 ) 
[On] and [Off].
Note
When [Rear] is set to [On], [Auto] is disabled. z
When this function is set to [On] or [Auto], the  z
[Sharpness] is disabled. 
						

							Image adjust
58 - ENGLISH
Settings
Sharpness
Press ▲▼ to select [Sharpness].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the setting value.3 ) 
OperationAdjustmentAdjustment 
range
Press ►.
increase the 
sharpness of the 
image
Maximum 
value 31
Press ◄.
decrease the 
sharpness of the 
image
Minimum 
value 0
Gamma
Press ▲▼ to select [Gamma].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to adjust the gamma value 3 ) 
to obtain a better balance of contrast.
Adjustments can be made between z 0 and 15.
Noise reduction
Press ▲▼ to select [Noise reduction].1 ) 
Press the  button to display 2 ) 
the adjustment dialog box.
Press ◄► to select the desired item.3 ) 
OffDisabled
OnThe function works
Noise interference on the screen can be  z
reduced. Select one of the above options to get 
smoother images.
[Noise reduction] cannot be selected when   z
[1 080p] is selected.
Note
When input video signal to the projector, [Noise  z
reduction] will become available.
Progressive
Press ▲▼ to select [Progressive].1 ) 
Press the  button to display 2 ) 
the dialog box.
Press ◄► to select the desired item.3 ) 
An interlaced video signal can be displayed in  z
progressive mode. Select one of the following 
options.
[Progressive] cannot be selected when [480p],  z
[576p], [720p] or [1 080p] is selected.
OffDisabled
OnThe function works
FilmFor watching a film
Note
When input video signal to the projector, [Progressive]  z
will become available.
Reset
To reset the adjusted data, all adjustments will return 
to their previous figures.
Press ▲▼ to select [Reset].1 ) 
Press the  button.2 ) 
A confirmation box appears and then select [Yes]. z 
Note
To reset the adjusted data except [Daylight View]. z
Store
Press ▲▼ to select [Store].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to select one from Image 1 3 ) 
to 10 and press the  button.
A confirmation box appears and then select [Yes]. z
Note
To store the adjusted data except [Daylight View]. z
Make sure you selected [Store] after adjusting settings.  z
Some settings can not be stored if not registered with 
[Store] function. 
						

							ENGLISH - 59
Settings
Screen 
Select [Screen] from the Main Menu (see 
“Navigating through the menu” on page 47), 
then select the item from the sub-menu.
Remote ControlSide Control
Normal
Provide the image to fit the screen size while 
maintaining the aspect ratio of the input signal.
Press ▲▼ to select [Normal] and then 
press the  button.
Full 
Provide the full screen image.
Press ▲▼ to select [Full] and then press 
the  button.
Wide(16:9)
Provide the image at the 16:9 wide screen ratio.
Press ▲▼ to select [Wide(16:9)] and then 
press the  button.
Zoom
Scale the image proportionally to fit the entire screen. 
Either side of image may go over the screen.
Press ▲▼ to select [Zoom] and then 
press the  button.
True 
Provide the image in its original size. When the 
original image size is larger than the panel size*, the 
projector enters to the panning mode automatically.
Press ▲▼ to select [True] and then 1 ) 
press the  button.
Press ▲▼◄► to pan the image.2 ) 
When adjusted, the arrows will turn red. When  z
reached to the correction limits, the arrows will 
disappear.
*Different models have different Panel sizes.
Panel sizeModel
1 280 x 800EW630 series, EW530 series
1 024 x 768EX600 series, EX500 series
1 920 x 1 200EZ570 series
Note
When input computer signal to the projector, [True] will  z
be available.
[True] is disabled and cannot be displayed when [480i],  z
[576i], [480p], [576p], [720p], [1 035i] or [1 080i] is 
selected in the PC System Menu.
When [True] is selected in the Screen menu, [Digital  z
zoom +/-] cannot be selected.
Natural wide 
Modify the 4:3 aspect ratio image to fit the screen size  
by stretching the image to make it look natural.
Press ▲▼ to select [Natural wide*] and 
then press the  button. 
* This function is not available for EX600 series, EX500 
series.
Note
When input video signal to the projector, [Natural wide]  z
will be available.
[Natural wide] is not available when [720p], [1 035i] or   z
[1 080i] is selected in the PC System Menu.
Custom
Provide the last stored aspect screen image.
Press ▲▼ to select [Custom] and press 
the  button.  
						

							Screen 
60 - ENGLISH
Settings
Custom adj.
Adjust the screen scale and position manually with 
this function.
Press ▲▼ to select [Custom adj.].1 ) 
Press ► or the  button to 2 ) 
enter the next submenu.
Press ▲▼ to choose the item you 3 ) 
want to adjust.
You can choose one from the items as below: z
Scale H/VAdjust the Horizontal/Vertical screen 
scale.
H&VWhen set to [On], the aspect ratio is 
fixed.
Position H/VAdjust the Horizontal/Vertical screen 
position.
CommonSave the adjusted scale or position 
to all the inputs.
ResetReset the all adjusted values.
Digital zoom +
Zoom in the images.
Press ▲▼ to select [Digital zoom +] 1 ) 
and then press the  button.
The On-Screen Menu disappears and                                 z
[D. zoom + ] appears.
Press the  button to zoom in 2 ) 
the image size and press ▲▼ ◄► to 
move the image to the top/bottom/left/
right of the screen.
The Panning function can work only when the  z
image is larger than the screen size. A projected 
image can be also expanded by pressing the 
 or the  button.
Digital zoom -
Zoom out the images.
Press ▲▼ to select [Digital zoom -] 1 ) 
and then press the  button.
The On-Screen Menu disappears and                                                                                                                                               z
[D.zoom - ] appears.
Press the  button to zoom 2 ) 
out image size.
The projected image can be also compressed  z
by pressing the  or the  
button.
To exit the Digital zoom +/– mode, press any button 
except the ,  and ▲▼◄► 
buttons.
To return to the previous screen size, select a screen 
size from the Screen Size Adjustment Menu or select 
an input source from the Input Source Selection Menu 
(Æpage 50) again, or adjust the screen size with the 
 buttons.
Note
When input computer signal to the projector, this function  z
will be available.
[Digital zoom +/-] cannot be selected when [True] is  z
selected in the Screen aspect.
[Digital zoom +/–] are disabled and cannot be displayed  z
when [480i], [576i], [480p], [576p], [720p], [1 035i] or  
[1 080i] is selected in the PC System Menu (Æpage 51).
When [Digital zoom +/–] functions are disabled,  z mark will appear.
Keystone
This function is used to adjust keystone distortion of 
the projected image.
Press ▲▼ to select [Keystone].1 ) 
Press ► or the  button.2 ) 
Press ▲▼ to choose the item you 3 ) 
want to adjust.
Standard
Adjust the Horizontal/Vertical 
keystone distortion of the projected 
image.*1
Corner 
correction
Adjust the corner distortion of the 
projected image.
Corner 
pattern
Choose a Corner pattern mode 
among [Red], [White], [Blue], and 
[Off].
StoreTo store or reset the keystone 
correction.
Store
Keep the keystone correction even 
when the AC power cord is plugged 
out or turned off the projector.
Reset
Release the keystone correction 
when the AC power cord is plugged 
out.
Adjust the Vertical keystone distortion of the *1 : 
projected image. 
Note
For details, see “Using the KEYSTONE button” of "Basic  z
operation by using the remote control" (Æpage 45).
The following items are the 
submenus of [Store].