Panasonic Projector PT-RQ13K User Manual

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 111
10) Press the  button.
 fThe confirmation screen is displayed.
1

1)  
Press 
 qw to select [OK], and press the  button.
Note
 f The settings in [RESOLUTION] and [VER TICAL SCAN FREQUENCY] are displayed in [EDID STATUS]. fThe resolution and vertical scanning frequency settings may also be required on your computer or video device. fAfter configuring settings, your computer or video device or the projector may be required to be turned of f and on. fA

 signal may not be output with the resolution and vertical scanning frequency that have been set, depending on your computer or video 
device.
[SLOT IN]
Set this item in accordance with the signal input to the input terminal of the installed Interface Board when the 
optional Interface Board is installed in the slot.
The content that can be set varies depending on the structure of the installed Interface Board. It cannot be set if 
no Interface Board is installed in the slots.
When the optional Interface Board for HDMI 2 input (Model No.: ET- MDNHM10) is installed
Setting [HDMI LINK] in [SLOT IN] (HDMI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [HDMI LINK], and press the  button.
 fThe 

[HDMI LINK] screen is displayed.
4)
 
Press 
 as to select the setting.
[AUTO] Automatically selects the single link, the dual link, or the quad link.
Selects the quad link when the signal in the same format (such as resolution and timing) is input in 
the four inputs of HDMI1, HDMI2, HDMI3, and HDMI4. Selects the dual link when the signal in the 
same format is input in the HDMI1 input and the HDMI2 input, or the HDMI3 input and the HDMI4.
Quad link will be automatically selected when the optional Interface Board for HDMI 2 input (Model 
No.: ET
-

MDNHM10) is installed in both of the slots.
[SINGLE] Sets the HDMI1 input and the HDMI2 input, and the HDMI3 input and the HDMI4 input to single link.
(Factory default setting)
[DUAL]
*1Sets the HDMI1 input and the HDMI2 input, or the HDMI3 input and the HDMI4 input to dual link.
[DUAL/SINGLE]
*2Sets the HDMI1 input and the HDMI2 input to dual link, and the HDMI3 input and the HDMI4 input to 
single link.
[SINGLE/DUAL]
*2Sets the HDMI1 input and the HDMI2 input to single link, and the HDMI3 input and the HDMI4 input 
to dual link.
[DUAL/DUAL]
*2Sets the HDMI1 input and the HDMI2 input to dual link, and the HDMI3 input and the HDMI4 input to 
dual link.
[QUAD]
*2Sets the HDMI1 input, the HDMI2 input, the HDMI3 input, and the HDMI4 input to quad link.
*1 This can be selected when the optional Interface Board for HDMI 2 input (Model No.: ET- MDNHM10) is installed in either of the slots.
*2  
This can be selected when the optional Interface Board for HDMI 2 input (Model No.: ET-
 MDNHM10) is installed in both of the slots.
5) Press the  button.
Note
 f [HDMI LINK] is fixed to [SINGLE] in the following cases. gWhen [SIMUL
 INPUT SETTING] is set to anything other than [OFF]
 gWhen the [MUL

TI DISPLAY] menu → [MULTI DISPLAY MODE] is set to anything other than [OFF] and displaying the four-screen display
 fThe [HDMI LINK] setting cannot be changed when [BACKUP

 INPUT MODE] in [BACKUP INPUT SETTING] is set as the combination used 
for the HDMI input of the Interface Board.
 f The content set is displayed in [HDMI LINK SETTINGS].  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
112 - ENGLISH
 rStructure of the projected image
The single link is a setting to display one image with one input signal.  The dual link is a setting to display one 
image with two input signals. The quad link is a setting to display one image with four input signals.
Dual link
HDMI1/
HDMI3 HDMI1 HDMI2
HDMI3 HDMI4
HDMI2/
HDMI4
Quad link
Single link
Setting [SIGNAL LEVEL] in [SLOT IN] (HDMI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and 
press the  button.
 f The 

[SINGLE LINK SETTING]  screen, the [DUAL LINK SETTING]  screen, or the [QUAD LINK SETTING]  
screen is displayed.
4)
 
Press 
 as to select [SIGNAL LEVEL].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically sets the signal level.
[64-940] Select this item when the HDMI terminal output of the external device (such as Blu-ray disc player) 
is input to the  terminal, the  terminal, the  terminal, or the 
 terminal.
[0-1023] Select this item when the DVI
- D terminal output from the external device (such as computer) is input 
to the  terminal, the  terminal, the  terminal, or the  terminal via a conversion cable, etc.
This is the same when the HDMI terminal output from a device such as a computer is input to the 
 terminal, the  terminal, the  terminal, and the  
terminal.
Note
 f The optimal setting varies depending on the output setting of the connected external device. Refer to the operating instructions of the 
external device regarding the output of the external device.
 fThe HDMI signal level is displayed for 30

  bits of input.
Setting [EDID SELECT] in [SLOT IN] (HDMI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [EDID SETTING], and press the  button.
 fThe 

[EDID SETTING]  screen is displayed.
4)
 
Press 
 as to select [EDID SELECT].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[EDID1:4K/60p] Switches to EDID corresponding to the 4K video signal (maximum 4   096   x   2   160 dots, maximum 
vertical scanning frequency 60   Hz).  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 113
[EDID2:4K/30p]Switches to EDID corresponding to the 4K video signal (maximum 4   096   x   2   160 dots, maximum 
vertical scanning frequency 30   Hz).
[EDID3:2K] Switches to EDID corresponding to the 2K video signal (maximum 1
  920   x   1   200 dots) or lower.
Note
 fSwitch the setting to [EDID2:4K/30p] when proper image is not projected while [EDID SELECT] is set to [EDID1:4K/60p] and the 4K video 
signal is input.
 fSwitch the setting to [EDID3:2K] when proper image is not projected while [EDID SELECT] is set to [EDID1:4K/60p] or [EDID2:4K/30p] and 
the 2K video signal or lower is input.
 fFor details of the signal described in EDID of [EDID1:4K/60p], [EDID2:4K/30p], or [EDID3:2K], refer to “List of plug and play compatible 
signals” ( x

  page   213).
Setting [EDID MODE] in [SLOT IN] (HDMI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [EDID SETTING], and press the  button.
 fThe 

[EDID SETTING]  screen is displayed.
4)
 
Press 
 as to select [EDID MODE].
5)
 
Press the  button.
 f The 

[HDMI EDID MODE] screen is displayed.
6)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Standard setting.
[USER] Set the [RESOLUTION] and [VERTICAL SCAN FREQUENCY] items as EDID.
 fWhen [DEF AULT] is selected, proceed to Step 11 ) .
7)
 
Press the  button.
 f The 

[RESOLUTION] screen is displayed.
8)
 
Press 
 asqw  to select [RESOLUTION].
 fSelect [1024x768p], [1280x720p], [1280x768p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p], 
[1440x900p], [1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], [1920x1200p], 
[1920x2160p], [2048x1080p], [2048x2160p], or [2560x1600p].
9)

 
Press the  button.
 f The 

[VERTICAL SCAN FREQUENCY] screen is displayed.
10)
 
Press 
 qw to select [VERTICAL SCAN FREQUENCY].
 fSelect [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [2048x2160p], [2048x1080p], [1920x2160p], or 
[1920x1080p] is selected for [RESOLUTION].
 fSelect [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
 fSelect [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
 g[2048x2160p], [2048x1080p], [1920x2160p], [1920x1080p], [1920x1080i]
1

1)
 
Press the  button.
 f The confirmation screen is displayed.
12)

 
Press 
 qw to select [OK], and press the  button.
Note
 f The settings in [RESOLUTION] and [VER TICAL SCAN FREQUENCY] are displayed in [EDID STATUS]. fThe resolution and vertical scanning frequency settings may also be required on your computer or video device. fAfter configuring settings, your computer or video device or the projector may be required to be turned of f and on. fA

 signal may not be output with the resolution and vertical scanning frequency that have been set, depending on your computer or video 
device.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
114 - ENGLISH
When the optional Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10) is installed
Setting [DVI-D LINK] in [SLOT IN] (DVI-D input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [DVI-D LINK], and press the  button.
 fThe 

[DVI-D LINK] screen is displayed.
4)
 
Press 
 as to select the setting.
[AUTO] Automatically selects the single link, the dual link, or the quad link.
Selects the quad link when the signal in the same format (such as resolution and timing) is input in 
the four inputs of DVI-D1, DVI-D2, DVI-D3, and DVI-D4. Selects the dual link when the signal in the 
same format is input in the DVI-D1 input and the DVI-D2 input, or the DVI-D3 input and the DVI-D4.
Quad link will be automatically selected when the optional Interface Board for DVI-D 2 input (Model 
No.: ET
-

MDNDV10) is installed in both of the slots.
[SINGLE] Sets the DVI-D1 input and the DVI-D2 input, and the DVI-D3 input and the DVI-D4 input to single link.
(Factory default setting)
[DUAL]
*1Sets the DVI-D1 input and the DVI-D2 input, or the DVI-D3 input and the DVI-D4 input to dual link.
[DUAL/SINGLE]
*2Sets the DVI-D1 input and the DVI-D2 input to dual link, and the DVI-D3 input and the DVI-D4 input to 
single link.
[SINGLE/DUAL]
*2Sets the DVI-D1 input and the DVI-D2 input to single link, and the DVI-D3 input and the DVI-D4 input 
to dual link.
[DUAL/DUAL]
*2Sets the DVI-D1 input and the DVI-D2 input to dual link, and the DVI-D3 input and the DVI-D4 input to 
dual link.
[QUAD]
*2Sets the DVI-D1 input, the DVI-D2 input, the DVI-D3 input, and the DVI-D4 input to quad link.
*1 This can be selected when the optional Interface Board for DVI-D 2 input (Model No.: ET- MDNDV10) is installed in either of the slots.
*2  
This can be selected when the optional Interface Board for DVI-D 2 input (Model No.: ET-
 MDNDV10) is installed in both of the slots.
5) Press the  button.
Note
 f [DVI-D LINK] is fixed to [SINGLE] in the following cases. gWhen [SIMUL
 INPUT SETTING] is set to anything other than [OFF]
 gWhen the [MUL

TI DISPLAY] menu → [MULTI DISPLAY MODE] is set to anything other than [OFF] and displaying the four-screen display
 fThe [DVI-D LINK] setting cannot be changed when [BACKUP

 INPUT MODE] in [BACKUP INPUT SETTING] is set as the combination used 
for the DVI
- D input of the Interface Board.
 fThe content set is displayed in [DVI-D LINK SETTINGS].
 rStructure of the projected image
The single link is a setting to display one image with one input signal.  The dual link is a setting to display one 
image with two input signals. The quad link is a setting to display one image with four input signals.
Dual link
DVI-D1/
DVI-D3 DVI-D1 DVI-D2
DVI-D3 DVI-D4
DVI-D2/
DVI-D4
Quad link
Single link
Setting [SIGNAL LEVEL] in [SLOT IN] (DVI-D input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 115
3) Press as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and 
press the  button.
 f The 

[SINGLE LINK SETTING]  screen, the [DUAL LINK SETTING]  screen, or the [QUAD LINK SETTING]  
screen is displayed.
4)
 
Press 
 as to select [SIGNAL LEVEL].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically sets the signal level.
[0-255:PC] Select this item when the DVI
- D terminal output of the external device (such as computer) is input to 
the  terminal, the  terminal, the  terminal, or the  terminal.
[16-235] Select this item when the HDMI terminal output from the external device (such as Blu-ray disc player) 
is input to the  terminal, the  terminal, the  terminal, or the 
 terminal via a conversion cable, etc.
Note
 f
The optimal setting varies depending on the output setting of the connected external device. Refer to the operating instructions of the 
external device regarding the output of the external device.
Setting [EDID SELECT] in [SLOT IN] (DVI-D input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [EDID SETTING], and press the  button.
 fThe 

[EDID SETTING]  screen is displayed.
4)
 
Press 
 as to select [EDID SELECT].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[EDID3] Recognizes moving image signals and still image signals automatically .
[EDID1] Select this item mainly when the external device (such as Blu-ray disc player) which outputs the 
moving image signal is connected to the  terminal, the  terminal, the 
 terminal, or the  terminal.
[EDID2:PC] Select this item mainly when the external device (such as computer) which outputs the still image 
signal is connected to the  terminal, the  terminal, the  
terminal, or the  terminal.
Note
 f
The data for Plug and play will change when the setting is changed. Refer to “List of compatible signals” ( x   page   210) for a resolution that 
supports plug and play.
Setting [EDID MODE] in [SLOT IN] (DVI-D input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [EDID SETTING], and press the  button.
 fThe 

[EDID SETTING]  screen is displayed.
4)
 
Press 
 as to select [EDID MODE].
5)
 
Press the  button.
 f The 

[DVI-D EDID MODE] screen is displayed.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
116 - ENGLISH
6) Press qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Standard setting.
[USER] Set the [RESOLUTION] and [VERTICAL SCAN FREQUENCY] items as EDID.
 fWhen [DEF AULT] is selected, proceed to Step 11 ) .
7)
 
Press the  button.
 f The 

[RESOLUTION] screen is displayed.
8)
 
Press 
 asqw  to select [RESOLUTION].
 fSelect [1024x768p], [1280x720p], [1280x768p], [1280x800p], [1280x1024p], [1366x768p], [1400x1050p], 
[1440x900p], [1600x900p], [1600x1200p], [1680x1050p], [1920x1080p], [1920x1080i], [1920x1200p], 
[1920x2160p], [2048x1080p], or [2048x2160p].
9)

 
Press the  button.
 f The 

[VERTICAL SCAN FREQUENCY] screen is displayed.
10)
 
Press 
 qw to select [VERTICAL SCAN FREQUENCY].
 fSelect [30Hz], [25Hz], or [24Hz] when [2048x2160p] or [1920x2160p] is selected for [RESOLUTION].
 fSelect [60Hz], [50Hz], [30Hz], [25Hz], or [24Hz] when [2048x1080p] or [1920x1080p] is selected for 
[RESOLUTION].
 fSelect [60Hz], [50Hz], or [48Hz] when [1920x1080i] is selected for [RESOLUTION].
 fSelect [60Hz] or [50Hz] when anything other than following is selected for [RESOLUTION].
 g[2048x2160p], [1920x2160p], [2048x1080p], [1920x1080p], [1920x1080i]
1

1)
 
Press the  button.
 f The confirmation screen is displayed.
12)

 
Press 
 qw to select [OK], and press the  button.
Note
 f The settings in [RESOLUTION] and [VER TICAL SCAN FREQUENCY] are displayed in [EDID STATUS]. fThe resolution and vertical scanning frequency settings may also be required on your computer or video device. fAfter configuring settings, your computer or video device or the projector may be required to be turned of f and on. fA

 signal may not be output with the resolution and vertical scanning frequency that have been set, depending on your computer or video 
device.
When the optional 3G-SDI Terminal Board with Audio (Model No.: TY- TBN03G) is installed
To use the 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G), it is necessary for the firmware version of 
the 3G-SDI Terminal Board with Audio to be 2.00 or later. Consult your dealer regarding the version update to the 
latest firmware if the version is earlier than 2.00.
For details on how to confirm the firmware version, refer to “How to confirm the firmware version of the 3G-SDI 
Terminal Board with Audio” (x
  page   31).
Setting [SDI LINK] in [SLOT IN] (SDI input)
1)
 
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 fThe 

[SLOT IN] screen is displayed.
3)
 
Press 
 as to select [SDI LINK], and press the  button.
 fThe 

[SDI LINK] screen is displayed.
4)
 
Press 
 as to select the setting.
[AUTO] Automatically selects the single link, the dual link, or the quad link.
The single link, dual link, or quad link is automatically distinguished by reading the payload ID 
attached to each input signal. Single link will be selected when a payload ID is not added to the input 
signal.
Quad link will be automatically selected when the optional 3G-SDI 
Terminal Board with Audio (Model 
No.: TY
-

TBN03G) is installed in both of the slots.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 117
[SINGLE]Sets the SDI1 input and the SDI2 input, and the SDI3 input and the SDI4 input of the Interface Board 
to single link.
(Factory default setting)
[DUAL]
*1Sets the SDI1 input and the SDI2 input, or the SDI3 input and the SDI4 input of the Interface Board to 
dual link.
[DUAL/SINGLE]
*2Sets the SDI1 input and the SDI2 input of the Interface Board to dual link, and the SDI3 input and the 
SDI4 input of the Interface Board to single link.
[SINGLE/DUAL]
*2Sets the SDI1 input and the SDI2 input of the Interface Board to single link, and the SDI3 input and 
the SDI4 input of the Interface Board to dual link.
[DUAL/DUAL]
*2Sets the SDI1 input and the SDI2 input of the Interface Board to dual link, and the SDI3 input and the 
SDI4 input of the Interface Board to dual link.
[QUAD]
*2Sets the SDI1 input, the SDI2 input, the SDI3 input, and the SDI4 input of the Interface Board to quad 
link.
*1 This can be selected when the optional 3G-SDI  Terminal Board with Audio (Model No.: TY- TBN03G) is installed in either of the slots.
*2  
This can be selected when the optional 3G-SDI 
 Terminal Board with Audio (Model No.: TY
-
 TBN03G) is installed in both of the slots.
5) Press the  button.
Note
 f The single link is a setting to display one image with one input signal.  The dual link is a setting to display one image with two input signals. 
The quad link is a setting to display one image with four input signals.
 f [SDI LINK] is fixed to [SINGLE] in the following cases. gWhen [SIMUL

 INPUT SETTING] is set to anything other than [OFF]
 gWhen the [MUL

TI DISPLAY] menu → [MULTI DISPLAY MODE] is set to anything other than [OFF] and displaying the four-screen display
 fThe [SDI LINK] setting cannot be changed when [BACKUP

 INPUT MODE] in [BACKUP INPUT SETTING] is set as the combination used for 
the SDI input of the Interface Board.
 f The content set is displayed in [SDI LINK SETTINGS].
Setting [RESOLUTION] in [SLOT IN] (SDI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and 
press the  button.
 f The 

[SINGLE LINK SETTING]  screen, the [DUAL LINK SETTING]  screen, or the [QUAD LINK SETTING]  
screen is displayed.
4)
 
Press 
 as to select [RESOLUTION], and press the  button.
 fThe 

[RESOLUTION] screen is displayed.
5)
 
Press 
 as to select an item, and press the  button.
 fSelect [AUT

O], [720x480i], [720x576i], [1280x720p], [1920x1080i], [1920x1080p], [1920x1080sF], 
[2048x1080p], or [2048x1080sF] when [SINGLE LINK SETTING] is selected.
 f Select [AUT

O], [1920x1080i], [1920x1080p], [1920x1080sF], [2048x1080p], [2048x1080sF], [3840x2160p], 
or [4096x2160p] when [DUAL LINK SETTING] is selected.
 f Select [AUT

O], [3840x2160p], [3840x2160sF], [4096x2160p], or [4096x2160sF] when [QUAD LINK 
SETTING] is selected.
Setting [4K DIVISION] in [SLOT IN] (SDI input)
Set the transmission method in the 4K format when displaying the 4K image with dual link or quad link.
1)
 
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [DUAL LINK SETTING] or [QUAD LINK SETTING], and press the  button.
 fThe 

[DUAL LINK SETTING]  screen or the [QUAD LINK SETTING] screen is displayed.
4)
 
Press 
 as to select [4K DIVISION].  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
118 - ENGLISH
5) Press qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically selects [SQUARE] or [INTERLEAVE].
[SQUARE] or [INTERLEAVE] is automatically selected by reading the payload ID attached to the 
input signal.
[SQUARE] Fixes the transmission method to Square Division.
[INTERLEAVE] Fixes the transmission method to 2-Sample Interleave Division.
Setting [3G-SDI MAPPING] in [SLOT IN] (SDI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and 
press the  button.
 f The 

[SINGLE LINK SETTING]  screen, the [DUAL LINK SETTING]  screen, or the [QUAD LINK SETTING]  
screen is displayed.
4)
 
Press 
 as to select [3G-SDI MAPPING].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button. 
[AUTO] Automatically selects [LEVEL A] or [LEVEL B].
[LEVEL A] Fixes the mapping method to 3G-SDI Level-A.
[LEVEL B] Fixes the mapping method to 3G-SDI Level-B.
Note
 fThis function does not operate when the SD - SDI signal or the HD - SDI signal is input.
Setting [COLOR SPACE] in [SLOT IN] (SDI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and 
press the  button.
 f The 

[SINGLE LINK SETTING]  screen, the [DUAL LINK SETTING]  screen, or the [QUAD LINK SETTING]  
screen is displayed.
4)
 
Press 
 as to select [COLOR SPACE].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically selects [RGB] or [YPBPR].
[RGB] or [YP
BPR] is automatically selected by reading the payload ID attached to the input signal. 
[RGB] is selected when the payload ID is not attached to the input signal.
[RGB] Fixes to [RGB].
[YP
BPR] Fixes to [YPBPR].
Setting [SAMPLING] in [SLOT IN] (SDI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 119
3) Press as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and 
press the  button.
 f The 

[SINGLE LINK SETTING]  screen, the [DUAL LINK SETTING]  screen, or the [QUAD LINK SETTING]  
screen is displayed.
4)
 
Press 
 as to select [SAMPLING].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Automatically selects [4:4:4] or [4:2:2].
[4:4:4] or [4:2:2] is automatically selected by reading the payload ID attached to the input signal. 
[4:2:2] is selected when the payload ID is not attached to the input signal.
[4:4:4] Fixes to [4:4:4].
[4:2:2] Fixes to [4:2:2].
Setting [BIT DEPTH] in [SLOT IN] (SDI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and 
press the  button.
 f The 

[SINGLE LINK SETTING]  screen, the [DUAL LINK SETTING]  screen, or the [QUAD LINK SETTING]  
screen is displayed.
4)
 
Press 
 as to select [BIT DEPTH].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button. 
[AUTO] Automatically select [12-bit] or [10-bit].
[12-bit] Fixes to [12-bit].
[10-bit] Fixes to [10-bit].
Setting [SIGNAL LEVEL] in [SLOT IN] (SDI input)
1)  
Press 
 as to select [SLOT IN].
2)
 
Press the  button.
 f The 

[SLOT IN]  screen is displayed.
3)
 
Press 
 as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and 
press the  button.
 f The 

[SINGLE LINK SETTING]  screen, the [DUAL LINK SETTING]  screen, or the [QUAD LINK SETTING]  
screen is displayed.
4)
 
Press 
 as to select [SIGNAL LEVEL].
5)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[64-940] Normally use this setting.
[4-1019] Select this item when gray is displayed as black.
[FRAME SYNC SETTING]
Set if the frames are to be synchronized between the multiple projectors.  
						

							Chapter 4 Settings — [DISPLAY OPTION] menu
120 - ENGLISH
Frames of the projected images can be synchronized by linking multiple projectors using the  terminal and the  terminal. A combined screen with a balanced contrast can 
be displayed by sharing the brightness level of the video signal input to each projector when a multi-display is 
constructed by linking the projected images of multiple projectors.
For details of how to connect the projectors, refer to “Connection example when multiple projected images are to 
be synchronized” (x
  page   51).
1)
 
Press 
 as to select [FRAME SYNC SETTING].
2)
 
Press the  button.
 fThe 

[FRAME SYNC SETTING] screen is displayed.
3)
 
Press 
 as to select [FRAME SYNC].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Select this item when the frames are not to be synchronized.
[MASTER] Select this item when the frames are to be synchronized.
Set this item in the one projector that is to be the synchronization source.
[SLAVE] Select this item when the frames are to be synchronized.
Set this item in all the projectors that are to be the synchronization target.
 f
When anything other than [OFF] is selected, proceed to Step  5) .
The usage of the  terminal and the  terminal is 
displayed in [FRAME SYNC1] and [FRAME SYNC2] in the  [FRAME SYNC SETTING] screen.
The contents that are displayed are as follows.
[FRAME SYNC] [FRAME SYNC1] [FRAME SYNC2]
[MASTER] [OUTPUT] is displayed.
The  terminal will 
operate as an output terminal.
Connect to the  
terminal of the projector that is to be the 
synchronization target. [OUTPUT] is displayed.
The  terminal will operate 
as an output terminal.
Connect to the  
terminal of the projector that is to be the 
synchronization target.
[SLAVE] [INPUT] is displayed.
The  terminal will 
operate as an input terminal. [OUTPUT] is displayed.
The  terminal will operate 
as an output terminal.
5) Press 
as to select [CONTRAST SYNC].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Select this item when the contrast is not balanced in the combined screen.
[ON] Select this item when the contrast is balanced in the combined screen.
The synchronization source projector with [FRAME SYNC] set to [MASTER] will calculate the 
brightness level of the video signal to become optimum on the whole combined screen for every 
frame. All the projectors targeted to link will control the dynamic contrast function based on the 
calculation result.
 f
When [ON] is selected, the usage of the  terminal displayed in [FRAME SYNC1] 
is switched.
The contents that are displayed are as follows.
[FRAME SYNC] [FRAME SYNC1] [FRAME SYNC2]
[MASTER] [INPUT] is displayed.
The  terminal will 
operate as an input terminal.
Connect to the  terminal 
of the last projector. [OUTPUT] is displayed.
The  terminal will operate 
as an output terminal.
Connect to the  
terminal of the first projector that is to be the 
synchronization target.
[SLAVE] [INPUT] is displayed.
The  terminal will 
operate as an input terminal. [OUTPUT] is displayed.
The  terminal will operate 
as an output terminal.
 f
When [ON] is selected, the diagnosis result if the target projector is correctly connected is displayed in 
[ST
ATUS].