Panasonic Projector PT-RQ13K User Manual

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 171
Error information page
When [Error (Detail)] or [Warning (Detail)] is displayed in the [SELF TEST] display field of the [Projector status] 
screen, click it to display the content of the error/warning.
 fThe projector may go into the standby status to protect the projector depending on the contents of the error .
1
1 Self-diagnosis result display
Displays the item check results.
[OK]:
Indicates that operation is normal.
[F
AILED]:
Indicates that there is a problem.
[WARNING]:
Indicates that there is a warning.
 r [FAILED] items
Item Description
[MAIN CPU BUS] There is a problem with the microcomputer circuitry. Consult your dealer.
[FAN] There is a problem with the fan or the fan drive circuit. Consult your dealer .
[INTAKE AIR TEMPERATURE] The intake air temperature is high. The projector may be used in an environment where 
the temperature is high, such as near a heating appliance.
[OPTICS MODULE TEMPERATURE] The temperature around the optics module inside the projector is high. 
The projector 
may be used in an environment where the temperature is high, such as near a heating 
appliance.
[EXHAUST AIR TEMPERATURE] The exhaust air temperature is high. The projector may be used in an environment 
where the temperature is high, such as near a heating appliance. Or the air exhaust port 
may be blocked.
[LD1 TEMPERATURE] The temperature of the light source is high. The projector may be used in an 
environment where the temperature is high, such as near a heating appliance.
[LD2 TEMPERATURE]
[LD1 STATUS] The light source has failed to turn on. Consult your dealer.
[LD2 STATUS]
[SHUTTER(MUTE-SHUTTER)] There is a problem with the shutter circuitry. Consult your dealer.
[INTAKE AIR TEMP.SENSOR] There is a problem with the sensor used to detect intake temperature. Consult your 
dealer.
[OPTICS MODULE TEMP.SENSOR] There is a problem with the sensor used to detect temperature inside the projector
. 
Consult your dealer.
[EXHAUST AIR TEMP.SENSOR] There is a problem with the sensor used to detect exhaust air temperature. Consult your 
dealer.
[LD1 TEMP.SENSOR] There is a problem with the temperature detection sensor of light source 1. Consult your 
dealer.
[LD2 TEMP.SENSOR] There is a problem with the temperature detection sensor of light source 2. Consult your 
dealer.
[POWER CIRCUIT TEMPERATURE] The temperature around the power circuit is high. The air intake port may be blocked.
[FPGA TEMPERATURE] The temperature inside the projector is high. The air intake port may be blocked.
[LENS MOUNTER] There is a problem in the lens mounter. Consult your dealer.  
						

							Chapter 4 Settings — [NETWORK] menu
172 - ENGLISH
ItemDescription
[BRIGHTNESS SENSOR] There is a problem with the luminance sensor. If problems persist even after switching 
on the power, consult your dealer.
[PHOSPHOR WHEEL1] There is a problem with the phosphor wheel 1 or phosphor wheel 1 drive circuit. Consult 
your dealer.
[PHOSPHOR WHEEL2] There is a problem with the phosphor wheel 2 or phosphor wheel 2 drive circuit. Consult 
your dealer.
[QUAD PIXEL DRIVE UNIT] There is a problem with the QUAD PIXEL DRIVE unit handling the function to enhance 
the resolution of the projected image, or its drive circuit. Consult your dealer
.
[FILTER UNIT] The air filter unit is not attached. Check the connection of the air filter unit. 
(x
  page   188)
 r[WARNING] items
Item Description
[INTAKE AIR TEMPERATURE] The intake temperature is high. The projector may be used in an environment where the 
temperature is high, such as near a heating appliance.
[OPTICS MODULE TEMPERATURE] The temperature around the optics module inside the projector is high. 
The projector 
may be used in an environment where the temperature is high, such as near a heating 
appliance.
[EXHAUST AIR TEMPERATURE] The exhaust air temperature is high. The projector may be used in an environment 
where the temperature is high, such as near a heating appliance. Or the air exhaust port 
may be blocked.
[LD1 TEMPERATURE] The temperature of the light source is high. The projector may be used in an 
environment where the temperature is high, such as near a heating appliance.
[LD2 TEMPERATURE]
[POWER CIRCUIT TEMPERATURE] The temperature around the power circuit is high. The air intake port may be blocked.
[FPGA TEMPERATURE] The temperature inside the projector is high. The air intake port may be blocked.
[BATTERY] Battery replacement is required. Consult your dealer.
[AIR FILTER] There is too much dust accumulated in the air filter. Set the  switch to 
 (
x
  page   63), and clean the air filter. (x   page   188)
[AC VOLTAGE] The input supply voltage is low. Use electric wiring that can sufficiently withstand the 
power consumption of the projector.
[LOW-TEMPERATURE] The temperature around the optics module inside the projector is low
. Projection cannot 
be started until the optics module becomes warm.
[Network status] page
Click [Status] → [Network status].
The current network setting status is displayed.  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 173
[Access error log] page
Click [Status] → [Access error log].
The error log on the web server is displayed such as access to the pages that do not exist or access with 
unauthorized user names or passwords.
[Mail error log] page
Click [Status] → [Mail error log].
E-mail error log is displayed if periodic E-mail sending has failed.
Note
 f[Access error log] and [Mail error log] display the recent few thousand accesses/requests.  All information may not be displayed when many 
accesses/requests are made at once.
 f Logs in [Access error log] and [Mail error log] are deleted from the oldest when exceeding a certain amount.
 fCheck [Access error log] and [Mail error log] periodically

.  
						

							Chapter 4 Settings — [NETWORK] menu
174 - ENGLISH
[Basic control] page
Click [Projector control] → [Basic control].
1
2
3
4
6
5
1 [POWER]
T
urns on/off the power.
2
 
[SHUTTER]
Switches whether to use the shutter function (enabled (shutter: 
closed)/disabled (shutter: open)).
3

 
[OSD]
Switches on (display)/of

f (hide) the on-screen display function.
4
 
[SYSTEM]
Switches the system method. 5

 On-screen display of the projector
Displays the same items as shown on the on-screen display 
of the projector
. You can check or change the settings of the 
menus. It is displayed even if the on-screen display function is 
set to off (hide).
6
 
[INPUT SELECT]
Switches the input signal.
The display content for the input selection button varies 
depending on the optional Interface Board installed in the slot.
[Detail control] page
Click [Projector control] → [Detail control].
5 4
6 3 2 1
9 8
7
10
1 [MULTI DISPLAY MODE]Switches the setting of the multi-display mode.
2
 
Control of the projector
The projector is controlled by clicking the buttons in the same 
way as the buttons on the remote control. 

After control, the on-
screen display of the projector at the right of the control page is 
updated.
3
 
[SUB MEMOR
 Y]
Switches the sub memory.
4
 
[SYSTEM DA
 YLIGHT VIEW]
Switches to system daylight view settings.
5
 
[FREEZE]
T

emporarily pauses the image. 6
 [W AVEFORM MONITOR]
Displays the waveform of the input signal.
7
 
[PROJECTION METHOD]
Switches the setting of the projection method.
8

 
[LENS]
Adjusts the projection lens.
9

 
[TEST P
 ATTERN]
Displays the test pattern.
10
 
[GET OSD]
Updates the on-screen display of the projector at the right of the 
control page.  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 175
[Network config] page
Click [Detailed set up] → [Network config].
 fClick [Network config] to display the  [CAUTION!]

 screen.
 fThe current settings are displayed by pressing the [Next] button.
 fClick [Change] to display the setting change screen.
1
2
3
4
5
6
7
8
1 [PROJECT OR NAME]
Enter the name of the projector. Enter the host name if it is 
required when using a DHCP server etc.
2
 
[DHCP
  ON], [DHCP OFF]
To enable the DHCP client function, set to [DHCP ON].
3
 
[IP
  ADDRESS]
Enter the IP address when not using a DHCP server.
4
 
[SUBNET MASK]
Enter the subnet mask when not using a DHCP

 server.
5
 
[DEF
 AULT GATEWAY]
Enter the default gateway address when not using a DHCP 
server. 6
 [DNS1]
Enter the DNS1 server address.
Permissible characters for the entry of DNS1 server address 
(primary):
Numbers (0 - 9), period (.)
(Example: 192.168.0.253)
7
 
[DNS2]
Enter the DNS2 server address.
A

vailable characters for the entry of DNS2 server address 
(secondary):
Numbers (0 - 9), period (.)
(Example: 192.168.0.254)
8
 
[Back], [Next]
Click the [Back] button to return to the original screen. 

The 
current settings are displayed by pressing the [Next] button. 
Click the [Submit] button to update the settings.
Note
 f When you use the “Forward” and “Back” functions of your browser , a warning message “Page has Expired” may appear. In that case, click 
[Network config] again since the following operation will not be guaranteed.
 f Changing LAN settings while connected to the LAN may cause the connection to cut out.  
						

							Chapter 4 Settings — [NETWORK] menu
176 - ENGLISH
[Adjust clock] page
Click [Detailed set up] → [Adjust clock].
1
2
3
4
5
6
7
1 [Time Zone]
Select the time zone.
2
 
[Set time zone]
Updates the time zone setting.
3

 
[NTP
  SYNCHRONIZATION]
Set to [ON] to adjust the date and time automatically.
4
 
[NTP
  SERVER NAME]
Enter the IP address or server name of the NTP server when 
you set to adjust the date and time manually.
(To enter the server name, the DNS server needs to be set up.) 5
 [Date]
Enter the date to be changed.
6
 
[T
 ime]
Enter the time to be changed.
7
 
[Submit]
Updates the date and time settings.
Note
 fThe replacement of the battery inside the projector is required when the time goes out of alignment right after correcting the time. Consult 
your dealer
.
[Ping test] page
Check whether the network is connected to the E-mail server, POP server, DNS server, etc.
Click [Detailed set up]  → [Ping test].
1
2 3
4
1 [Input IP  address]
Enter the IP address of the server to be tested.
2
 
[Submit]
Executes the connection test. 3

 Example of display when the connection has succeeded
4  
Example of display when the connection has failed  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 177
[E-mail set up] page
Send an E-mail to preset E-mail addresses (up to two addresses) when a problem has occurred.
Click [Detailed set up] → [E-mail set up].
1
2
3
4
5
6
1 [ENABLE]
Select [Enable] to use the E-mail function.
2
 
[SMTP
  SERVER NAME]
Enter the IP address or the server name of the E-mail server 
(SMTP). To enter the server name, the DNS server needs to be 
set up.
3
 
[MAIL
  FROM]
Enter the E-mail address of the projector. (Up to 63 characters 
in single byte)
4
 
[MEMO]
Enter information such as the location of the projector that 
notifies the sender of the E-mail. (Up to 63 characters in single 
byte) 5

 [MINIMUM TIME]
Change the minimum interval for the temperature warning 
E-mail. 
The default value is 60 minutes. In this case, another 
E-mail will not be sent for 60 minutes after sending the 
temperature warning E-mail even if it reaches the warning 
temperature.
6
 
[INT
 AKE AIR TEMPERATURE]
Change the temperature setting for the temperature warning 
mail. A temperature warning E-mail is sent when the 
temperature exceeds this value.  
						

							Chapter 4 Settings — [NETWORK] menu
178 - ENGLISH
8
7
9
8
7
7 [E-MAIL ADDRESS 1], [E-MAIL ADDRESS 2]
Enter the E-mail address to be sent. Leave [E-MAIL ADDRESS 
2] blank when two E-mail addresses are not to be used. 8
 Settings of the conditions to send E-mail
Select the conditions to send E-mail.
[MAIL
 CONTENTS]: 
Select either [NORMAL] or [SIMPLE].
[ERROR]: 
Send an E-mail when an error occurred in the self-diagnosis.
[INTAKE AIR TEMPERATURE]: 
Send an E-mail when the intake air temperature has reached 
the value set at the above field.
[PERIODIC REPORT]: 
Place a check mark on this to send an E-mail periodically.
It will be sent on the days and time with the check mark.
9
 
[Submit]
Update the settings.
[Authentication set up] page
Set the authentication items when POP authentication or SMTP authentication is necessary to send an E-mail.
Click [Detailed set up] → [Authentication set up].
1
2
3
4
5
6
7
8
1 [Auth]
Select the authentication method specified by your Internet 
service provider
.
2
 
[SMTP
  Auth]
Set when the SMTP authentication is selected.
3
 
[POP
  server name]
Enter the POP server name.
Allowed characters:
Alphanumerics (A - Z, a - z, 0 - 9)
Minus sign (-) and period (.)
4
 
[User name]
Enter the user name for the POP

 server or the SMTP server. 5
 [Password]
Enter the password for the POP
 server or the SMTP server.
6
 
[SMTP
  server port]
Enter the port number of the SMTP server.
(Normally 25)
7
 
[POP
  server port]
Enter the port number of the POP server.
(Normally 110)
8
 
[Submit]
Update the settings.  
						

							Chapter 4 Settings — [NETWORK] menu
ENGLISH - 179
Contents of E-mail sent
Example of the E-mail sent when E-mail is set
The following E-mail is sent when the E-mail settings have been established.
=== P anas onic  pr ojec t or  r epor t ( CO NF I G URE )  ===
P r ojec t or  T y pe  :  RQ 13K
S er ial No  :  123456789012
----- E-mail set up dat a -----
T EMPERAT URE WARNING  SET UP
MINIMUM TIME  at  [  60]  m inut es  int er v al
I NT A K E  A I R T E M P E RA T URE   O v er  [  46 degC /  114 degF  ]
E RRO R  [ OFF ]
INT AKE AIR T EMPERAT URE  [ O F F  ]
P E RI O DI C RE P O RT
S unday   [  O N ]   M onday   [  O N ]   T ues day   [  O N ]   Wednes day   [  O N ]
T hur s day   [  O N ]   F r iday   [  O N ]   S at ur day   [  O N ]
00: 00  [  O N ]   01: 00  [  O N ]   02: 00  [  O N ]   03: 00  [  O N ]
04: 00  [  O N ]   05: 00  [  O N ]   06: 00  [  O N ]   07: 00  [  O N ]
08: 00  [  O N ]   09: 00  [  O N ]   10: 00  [  O N ]   11: 00  [  O N ]
12: 00  [  O N ]   13: 00  [  O N ]   14: 00  [  O N ]   15: 00  [  O N ]
16: 00  [  O N ]   17: 00  [  O N ]   18: 00  [  O N ]   19: 00  [  O N ]
20: 00  [  O N ]   21: 00  [  O N ]   22: 00  [  O N ]   23: 00  [  O N ]
----- check syst em -----
M A I N CP U B US   [ O K ]
F A N  [ O K ]
INT AKE AIR T EMPERAT URE  [ O K ]
O PT ICS MO DULE T EMPERAT URE  [ O K ]
EXHAUST  AIR T EMPERAT URE  [ O K ]
LD1 T EMPERAT URE  [ O K ]
LD2 T EMPERAT URE  [ O K ]
LD1 ST AT US  [ O K ]
LD2 ST AT US  [ O K ]
S HUT T E R(M UT E -S HUT T E R)  [ O K ]
INT AKE AIR T EMP.SENSO R  [ O K ]
O PT ICS MO DULE T EMP.SENSO R  [ O K ]
EXHAUST  AIR T EMP.SENSO R  [ O K ]
LD1 T EMP.SENSO R  [ O K ]
LD2 T EMP.SENSO R  [ O K ]
P O WE R CI RCUI T  T E M P E RA T URE   [  O K  ]
F PG A T EMPERAT URE  [ O K ]
BAT T ERY  [ O K ]
LE NS  M O UNT E R  [ O K ]
BRIG HT NESS SENSO R  [ O K ]
PHO SPHO R WHEEL1  [ O K ]
PHO SPHO R WHEEL2  [ O K ]
Q UA D P I X E L DRI V E  UNI T   [ O K ]
F I LT E R UNI T   [ O K ]
A I R F I LT E R  [ O K ]
AC VO LT AG E  [ O K ]
( E r r or  c ode 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00)
I nt ak e air  t em per at ur e  :  27 degC /   80 degF
O pt ic s  m odule t em per at ur e  :  26 degC /   78 degF
E x haus t  air  t em per at ur e  :  28 degC /   82 degF
A r ound light 1 t em per at ur e  :  29 degC /   84 degF
A r ound light 2 t em per at ur e  :  28 degC /   82 degF
P RO JE CT O R RUNT I M E   81 H     
P O WE R O N  834 t im es
LD1- 1 O N  294 t im es
LD1-1 RUNT I M E   29 H     
LD1- 2 O N  294 t im es
LD1-2 RUNT I M E   29 H     
LD1- 3 O N  294 t im es
LD1-3 RUNT I M E   29 H     
LD2- 5 O N  430 t im es
LD2-5 RUNT I M E   41 H     
LD2- 6 O N  430 t im es
LD2-6 RUNT I M E   41 H     
-------- Current  st at us ---------
MAIN VERSIO N  0. 32
SUB VERSIO N  0. 04. 01
LD S T A T US
LD1- 1=O N LD1- 2=O N LD1- 3=O N LD1- 4=O N LD1- 5=O N LD1- 6=O N
LD2- 1=O N LD2- 2=O N LD2- 3=O N LD2- 4=O N LD2- 5=O N LD2- 6=O N
I NP UT   S DI 1
SIG NAL NAME  ---
S I G NA L F RE Q UE NCY   ---kHz /  ---Hz
REMO T E2 ST AT US  DISABLE
----- Wired Net work conf igurat ion -----
DHCP  Client   OFF
I P  addr es s   192. 168. 0. 8
M A C addr es s   12: 34: 56: 78: 90: 12
M on J an 01 12: 34: 56 20X X
----- Memo -----  
						

							Chapter 4 Settings — [NETWORK] menu
180 - ENGLISH
Example of the E-mail sent for an error
The following E-mail is sent when an error has occurred.
=== P anas onic  pr ojec t or  r epor t ( E RRO R)  ===
P r ojec t or  T y pe  :  RQ 13K
S er ial No  :  123456789012
----- check syst em -----
M A I N CP U B US   [ O K ]
F A N  [ O K ]
INT AKE AIR T EMPERAT URE  [ O K ]
O PT ICS MO DULE T EMPERAT URE  [ O K ]
EXHAUST  AIR T EMPERAT URE  [ O K ]
LD1 T EMPERAT URE  [ O K ]
LD2 T EMPERAT URE  [ O K ]
LD1 ST AT US  [ O K ]
LD2 ST AT US  [ O K ]
S HUT T E R(M UT E -S HUT T E R)  [ F AILED ]
INT AKE AIR T EMP.SENSO R  [ O K ]
O PT ICS MO DULE T EMP.SENSO R  [ O K ]
EXHAUST  AIR T EMP.SENSO R  [ O K ]
LD1 T EMP.SENSO R  [ O K ]
LD2 T EMP.SENSO R  [ O K ]
P O WE R CI RCUI T  T E M P E RA T URE   [  O K  ]
F PG A T EMPERAT URE  [ O K ]
BAT T ERY  [ O K ]
LE NS  M O UNT E R  [ O K ]
BRIG HT NESS SENSO R  [ O K ]
PHO SPHO R WHEEL1  [ O K ]
PHO SPHO R WHEEL2  [ O K ]
Q UA D P I X E L DRI V E  UNI T   [ O K ]
F I LT E R UNI T   [ O K ]
A I R F I LT E R  [ O K ]
AC VO LT AG E  [ O K ]
( E r r or  c ode 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00 00)
I nt ak e air  t em per at ur e  :  27 degC /   80 degF
O pt ic s  m odule t em per at ur e  :  26 degC /   78 degF
E x haus t  air  t em per at ur e  :  28 degC /   82 degF
A r ound light 1 t em per at ur e  :  29 degC /   84 degF
A r ound light 2 t em per at ur e  :  28 degC /   82 degF
P RO JE CT O R RUNT I M E   81 H     
P O WE R O N  834 t im es
LD1- 1 O N  294 t im es
LD1-1 RUNT I M E   29 H     
LD1- 2 O N  294 t im es
LD1-2 RUNT I M E   29 H     
LD1- 3 O N  294 t im es
LD1-3 RUNT I M E   29 H     
LD1- 4 O N  294 t im es
LD1-4 RUNT I M E   29 H     
LD1- 5 O N  294 t im es
LD1-5 RUNT I M E   29 H     
LD1- 6 O N  294 t im es
LD1-6 RUNT I M E   29 H     
LD2- 1 O N  430 t im es
LD2-1 RUNT I M E   41 H     
LD2- 2 O N  430 t im es
LD2-2 RUNT I M E   41 H     
LD2- 3 O N  430 t im es
LD2-3 RUNT I M E   41 H     
LD2- 4 O N  430 t im es
LD2-4 RUNT I M E   41 H     
LD2- 5 O N  430 t im es
LD2-5 RUNT I M E   41 H     
LD2- 6 O N  430 t im es
LD2-6 RUNT I M E   41 H     
-------- Current  st at us ---------
MAIN VERSIO N  0. 32
SUB VERSIO N  0. 04. 01
LD S T A T US
LD1- 1=O N LD1- 2=O N LD1- 3=O N LD1- 4=O N LD1- 5=O N LD1- 6=O N
LD2- 1=O N LD2- 2=O N LD2- 3=O N LD2- 4=O N LD2- 5=O N LD2- 6=O N
I NP UT   S DI 1
SIG NAL NAME  ---
S I G NA L F RE Q UE NCY   ---kHz /  ---Hz
REMO T E2 ST AT US  DISABLE
----- Wired Net work conf igurat ion -----
DHCP  Client   OFF
I P  addr es s   192. 168. 0. 8
M A C addr es s   12: 34: 56: 78: 90: 12
M on J an 01 12: 34: 56 20X X
----- Memo -----