Panasonic Projector PT-RZ575 User Manual

							Chapter 7 Appendix — Technical information
ENGLISH - 171
 rError response
String DetailsTermination 
symbol
Message “ERR1” Undefined control command
(CR)
0x0d
“ERR2”
Out of parameter range
“ERR3” Busy state or no-acceptable period
“ERR4” Timeout or no-acceptable period
“ERR5” Wrong data length
“ERRA” Password mismatch
Data length 4
  bytes ―1
  byte
 terminal
The  terminal of the projector conforms with RS-232C so that the projector can be connected to and 
controlled from a computer .
Connection
When connecting directly
Projector connecting terminals
Computer
D-Sub 9p (male) Communication cable (straight)
D-Sub 9p (female)
When connecting using DIGITAL LINK compatible device
DIGITAL LINK compatible device
Computer
D-Sub 9p (female)
Projector connecting terminals
DIGITAL LINK DIGITAL LINK
D-Sub 9p (male)Communication cable (straight)
LAN cable (straight)
Note
 f The destination of [RS-232C] ( x   page   114) must be set according to the connection method. fWhen connecting using a DIGIT
AL LINK compatible device, set the [PROJECTOR SETUP] menu → [ECO MANAGEMENT]  → [STANDBY 
MODE] to [NORMAL] to control the projector in the standby mode.
When [STANDBY MODE] is set to [ECO], the projector cannot be control during standby.
Pin assignments and signal names
D-Sub 9-pin (female) Outside view Pin No.
Signal name Details
(1) (5)(6) (9)
(1)
―NC
(2) TXDTransmitted data
(3) RXDReceived data
(4) ―NC
(5) GNDEarth
(6) ―NC
(7) CTS
Connected internally
(8) RTS
(9) ―NC      
						

							Chapter 7 Appendix — Technical information
172 - ENGLISH
Communication conditions (Factory default)
Signal levelRS - 232C-compliant
Sync. method Asynchronous
Baud rate 9
  600   bps
Parity None
Character length 8 bits
Stop bit 1 bit
X parameter None
S parameter None
Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this 
order. Add parameters according to the details of control.
(2 bytes)
2 ID characters (2 bytes) Semi-colon (1 byte) Colon (1 byte)
3 command characters (3 bytes) Parameter (undefined length)
Start (1 byte) ZZ, 01 to 64
ID designate
End (1 byte)
Basic format (has subcommands)
Parameter (6 bytes)*1
Symbol “+” or “–” (1 byte) and setting or adjustment va\
lue (5 
bytes)
Operation (1 byte)
*1
“=” (Set the value specified using parameter)
Sub command (5 bytes) Same as the basic format
*1 When transmitting a command which does not need a parameter
, an operation (E) and parameter are not necessary.
Attention
 fIf a command is sent after the light source starts lighting, there may be a delay in response or the command may not be executed.  T ry 
sending or receiving any command after 60 seconds.
 f When transmitting multiple commands, be sure to wait until 0.5 seconds h\
as elapsed after receiving the response from the projector before 
sending the next command. When transmitting a command which does not need a parameter , a colon (:) is not necessary

.
Note
 fIf a command cannot be executed, the “ER401” response is sent from the projector to the computer . fIf an invalid parameter is sent, the “ER402” response is sent from the projector to the computer . fID transmission in RS

- 232C supports ZZ (ALL) and 01 to 64.
 fIf a command is sent with an ID designated, a response will be sent to the computer only in the following cases. gIt matches the projector ID gID is designated as 

ALL and [RESPONSE(ID ALL)] is set to [ON]
 fSTX and ETX are character codes. STX shown in hexadecimal is 02, and ETX shown in hexadecimal is 03.  
						

							Chapter 7 Appendix — Technical information
ENGLISH - 173
Cable specification
1NC    NC 1
2 2
3 3
4 NC    NC 4
5 5
6 NC    NC 6
7 7
8 8
9 NC    NC 9
When connected to a computer
Projector
( terminal) Computer
(DTE specifications)
Control command
The following table lists the commands that can be used to control the p\
rojector using a computer.
 r
Projector control command
Command Details Parameter/response 
string Remark (parameter)
PON Power on
―To check if the power is on, use the “Power query” command.
POF Power standby
QPW Power query 000
001 STANDBY
Power on
IIS Switching the input 
signal VID
VIDEO
RG1 COMPUTER1
RG2 COMPUTER2
DVI DVI
- D
HD1 HDMI1
HD2 HDMI2
DL1 DIGITAL LINK
OSH Shutter control 0OPEN
QSH Shutter status query 1CLOSE
VSE Aspect ratio switch 0
DEFAULT/VID AUTO/AUTO
1 4:3
2 16:9
5 THROUGH
QSE Aspect ratio settings 
query 6
HV FIT
9 H FIT
10 V FIT
OPP P IN P execution 0
OFF
1 USER1
QPP P IN P setting query 2
USER2
3 USER3
OCS Sub memory switch 01 - 96Sub memory number
QSB Sub memory status 
query
 r
Projector control command (with sub command)
Command Sub command Details Remark
VXX RYCI1 COMPUTER1 input setting +00000 = RGB/YP
BPR, +00001 = Y/C  
						

							Chapter 7 Appendix — Technical information
174 - ENGLISH
 rLens control command
Command Sub command Details Remark
VXX LNSI2 Lens H shift
+00000 = Fine adjustment 1+, +00001 = Fine adjustment 1
-, +00100 
= Fine adjustment 2+, +00101 = Fine adjustment 2-, +00200 = Coarse 
adjustment+, +00201 = Coarse adjustment-VXX LNSI3 Lens V shift
VXX LNSI4 Lens focus
Two-window display combination list
l: P IN P (picture in picture) combination is possible
―: P IN P (picture in picture) combination is not possible
Sub window
Main window
COMPUTER1 COMPUTER2DVI-D VIDEO HDMI1 HDMI2 DIGIT AL 
LINK
COMPUTER1 input Still image signal
―l―
l
*1― l l
Moving image signal
Y/C signal
COMPUTER2 input Still image signal
l―
l l l ― ―
Moving image signal
DVI
-
D input Still image signal
―l―
l―
l l
Moving image signal
VIDEO input Video signal
l
*1l l ―
l l l
HDMI1 input Still image signal
―l―
l―
l l
Moving image signal
HDMI2 input Still image signal
l―
l l l ― ―
Moving image signal
DIGITAL LINK input Still image signal
l―
l l l ― ―
Moving image signal
*1 Only when the [DISPLA Y OPTION] menu → [COMPUTER IN/OUT] (COMPUTER1 input)  → [INPUT SETTING] is set to [RGB/YPBPR]
Control device password
To initialize your password, consult your distributor.  
						

							Chapter 7 Appendix — Technical information
ENGLISH - 175
List of compatible signals
The following table specifies the video signals compatible with the projector.
 fSymbols that indicate formats are as follows.
 gV

: VIDEO, Y/C
 gR: RGB (analog)
 gY

: YC
BCR/YPBPR (analog)
 gD: DVI

-
D
 g H: HDMI
 fInput corresponding to each item in the plug and play column is as follows.
 gCOMPUTER: COMPUTER1/COMPUTER2 input
 gDVI

-
D: DVI
-
D input
 g HDMI/DL: HDMI1/HDMI2 input, DIGIT

AL LINK input
Signal name
(SIGNAL FORMAT) Resolution
(Dots) Scanning freq.
Dot clock 
freq.
(MHz) Format Plug and play*1
Horizontal
(kHz)Vertical(Hz)COMPUTERDVI-D HDMI/
DL
EDID1 EDID2 EDID3
NTSC/NTSC4.43/ P
AL
-
M/PAL60 720
 
x
 
480i 15.7  59.9  ―V ― ― ― ― ―
PAL/PAL
-
N/SECAM 720
 
x
 
576i 15.6  50.0  ―V ― ― ― ― ―
480/60i 720
 
x
 
480i 15.7  59.9  13.5  R/Y ― ― ― ― ―
576/50i 720
 
x
 
576i 15.6  50.0  13.5  R/Y ― ― ― ― ―
480/60i 720 
(1
 
440)
 
x
 
480i
*215.7  59.9  27.0  D/H ― ― ― ― ―
576/50i 720 
(1
 
440)
 
x
 
576i
*215.6  50.0  27.0  D/H ― ― ― ― ―
480/60p 720
 
x
 
480 31.5  59.9  27.0  R/Y/D/H ―
l―
l l
576/50p 720
 
x
 
576 31.3  50.0  27.0  R/Y/D/H ―
l―
l l
720/60p 1
 
280
 
x
 
720 45.0  60.0  74.3  R/Y/D/H ―
l―
l l
720/50p 1
 
280
 
x
 
720 37.5  50.0  74.3  R/Y/D/H ―
l―
l l
1080/60i 1
 
920
 
x
 
1
 
080i 33.8  60.0  74.3  R/Y/D/H ―
l―
l l
1080/50i 1
 
920
 
x
 
1
 
080i 28.1  50.0  74.3  R/Y/D/H ―
l―
l l
1080/24p 1
 
920
 
x
 
1
 
080 27.0  24.0  74.3  R/Y/D/H ―
l―
l l
1080/24sF 1
 
920
 
x
 
1
 
080i 27.0  48.0  74.3  R/Y/D/H ― ― ― ― ―
1080/25p 1
 
920
 
x
 
1
 
080 28.1  25.0  74.3  R/Y/D/H ―
l―
l―
1080/30p 1
 
920
 
x
 
1
 
080 33.8  30.0  74.3  R/Y/D/H ― ― ― ― ―
1080/60p 1
 
920
 
x
 
1
 
080 67.5  60.0  148.5  R/Y/D/H ―
l―
l l
1080/50p 1
 
920
 
x
 
1
 
080 56.3  50.0  148.5  R/Y/D/H ―
l―
l l
640
 
x
 
400/70 640
 
x
 
400 31.5  70.1  25.2  R/D/H ― ― ― ― ―
640
 
x
 
400/85 640
 
x
 
400 37.9  85.1  31.5  R/D/H ― ― ― ― ―
640
 
x
 
480/60 640
 
x
 
480 31.5  59.9  25.2  R/D/H
l l l l l
640
 
x
 
480/67 640
 
x
 
480 35.0  66.7  30.2  R/D/H ― ― ― ― ―
640
 
x
 
480/73 640
 
x
 
480 37.9  72.8  31.5  R/D/H
l―
l l l
640
 
x
 
480/75 640
 
x
 
480 37.5  75.0  31.5  R/D/H
l―
l l l
640
 
x
 
480/85 640
 
x
 
480 43.3  85.0  36.0  R/D/H ― ― ― ― ―
800
 
x
 
600/56 800
 
x
 
600 35.2  56.3  36.0  R/D/H
l―
l l l
800
 
x
 
600/60 800
 
x
 
600 37.9  60.3  40.0  R/D/H
l―
l l l
800
 
x
 
600/72 800
 
x
 
600 48.1  72.2  50.0  R/D/H
l―
l l l
800
 
x
 
600/75 800
 
x
 
600 46.9  75.0  49.5  R/D/H
l―
l l l
800
 
x
 
600/85 800
 
x
 
600 53.7  85.1  56.3  R/D/H ― ― ― ― ―
832
 
x
 
624/75 832
 
x
 
624 49.7  74.6  57.3  R/D/H
l―
l l l
1024
 
x
 
768/50 1
 
024
 
x
 
768 39.6  50.0  51.9  R/D/H ― ― ― ― ―
1024
 
x
 
768/60 1
 
024
 
x
 
768 48.4  60.0  65.0  R/D/H
l―
l l l
1024
 
x
 
768/70 1
 
024
 
x
 
768 56.5  70.1  75.0  R/D/H
l―
l l l
1024

 
x
 
768/75 1
 
024
 
x
 
768 60.0  75.0  78.8  R/D/H
l―
l l l
1024
 
x
 
768/82 1
 
024
 
x
 
768 65.5  81.6  86.0  R/D/H ― ― ― ― ―
1024
 
x
 
768/85 1
 
024
 
x
 
768 68.7  85.0  94.5  R/D/H ― ― ― ― ―
1024
 
x
 
768/100 1
 
024
 
x
 
768 81.4  100.0  113.3  R/D/H ― ― ― ― ―
1024
 
x
 
768/120 1
 
024
 
x
 
768 98.7  120.0  139.1  R/D/H
l―
l l l  
						

							Chapter 7 Appendix — Technical information
176 - ENGLISH
Signal name
(SIGNAL FORMAT) Resolution
(Dots) Scanning freq.
Dot clock 
freq.
(MHz) Format Plug and play*1
Horizontal
(kHz)Vertical(Hz)COMPUTERDVI-D HDMI/
DL
EDID1 EDID2 EDID3
1
152
 
x
 
864/60 1
 
152
 
x
 
864 53.7  60.0  81.6  R/D/H ― ― ― ― ―
1152
 
x
 
864/70 1
 
152
 
x
 
864 64.0  70.0  94.2  R/D/H ― ― ― ― ―
1152
 
x
 
864/75 1
 
152
 
x
 
864 67.5  75.0  108.0  R/D/H ― ― ― ― ―
1152
 
x
 
864/85 1
 
152
 
x
 
864 77.1  85.0  119.7  R/D/H ― ― ― ― ―
1152
 
x
 
870/75 1
 
152
 
x
 
870 68.7  75.1  100.0  R/D/H
l―
l l l
1280
 
x
 
720/50 1
 
280
 
x
 
720 37.1  49.8  60.5  R/D/H ― ― ― ― ―
1280
 
x
 
720/60 1
 
280
 
x
 
720 44.8  59.9  74.5  R/D/H ― ― ― ― ―
1280
 
x
 
720/100 1
 
280
 
x
 
720 76.3  100.0  131.8  R/D/H ― ― ― ― ―
1280
 
x
 
720/120 1
 
280
 
x
 
720 92.6  120.0  161.6  R/D/H ― ― ― ― ―
1280
 
x
 
768/50 1
 
280
 
x
 
768 39.6  49.9  65.3  R/D/H ― ― ― ― ―
1280
 
x
 
768/60 1
 
280
 
x
 
768 47.8  59.9  79.5  R/D/H ― ― ― ― ―
1
 
280
 
x
 
768
*347.4  60.0  68.3  R/D/H ― ― ― ― ―
1280
 
x
 
768/75 1
 
280
 
x
 
768 60.3  74.9  102.3  R/D/H ― ― ― ― ―
1280
 
x
 
768/85 1
 
280
 
x
 
768 68.6  84.8  117.5  R/D/H ― ― ― ― ―
1280
 
x
 
800/50 1
 
280
 
x
 
800 41.3  50.0  68.0  R/D/H ― ― ― ― ―
1280
 
x
 
800/60 1
 
280
 
x
 
800 49.7  59.8  83.5  R/D/H ― ― ― ― ―
1
 
280
 
x
 
800
*349.3  59.9  71.0  R/D/H ― ― ― ― ―
1280
 
x
 
800/75 1
 
280
 
x
 
800 62.8  74.9  106.5  R/D/H ― ― ― ― ―
1280
 
x
 
800/85 1
 
280
 
x
 
800 71.6  84.9  122.5  R/D/H ― ― ― ― ―
1280
 
x
 
960/60 1
 
280
 
x
 
960 60.0  60.0  108.0  R/D/H ― ― ― ― ―
1280
 
x
 
1024/50 1
 
280
 
x
 
1
 
024 52.4  50.0  88.0  R/D/H ― ― ― ― ―
1280
 
x
 
1024/60 1
 
280
 
x
 
1
 
024 64.0  60.0  108.0  R/D/H ― ― ― ― ―
1280
 
x
 
1024/66 1
 
280
 
x
 
1
 
024 72.3  66.3  125.0  R/D/H ― ― ― ― ―
1280
 
x
 
1024/72 1
 
280
 
x
 
1
 
024 78.2  72.0  135.1  R/D/H ― ― ― ― ―
1280
 
x
 
1024/75 1
 
280
 
x
 
1
 
024 80.0  75.0  135.0  R/D/H
l―
l l l
1280
 
x
 
1024/85 1
 
280
 
x
 
1
 
024 91.1  85.0  157.5  R/D/H ― ― ― ― ―
1366
 
x
 
768/50 1
 
366
 
x
 
768 39.6  49.9  69.0  R/D/H ― ― ― ― ―
1366
 
x
 
768/60 1
 
366
 
x
 
768 47.7  59.8  85.5  R/D/H ― ― ― ― ―
1400
 
x
 
1050/50 1
 
400
 
x
 
1
 
050 54.1  50.0  99.9  R/D/H ― ― ― ― ―
1400
 
x
 
1050/60 1
 
400
 
x
 
1
 
050 64.0  60.0  108.0  R/D/H ― ― ― ― ―
1
 
400
 
x
 
1
 
050 65.3  60.0  121.8  R/D/H ― ― ― ― ―
1
 
400
 
x
 
1
 
050 65.2  60.0  122.6  R/D/H
l―
l l l
1400
 
x
 
1050/72 1
 
400
 
x
 
1
 
050 78.8  72.0  149.3  R/D/H ― ― ― ― ―
1400
 
x
 
1050/75 1
 
400
 
x
 
1
 
050 82.2  75.0  155.9  R/D/H ― ― ― ― ―
1440
 
x
 
900/50 1
 
440
 
x
 
900 46.3  49.9  86.8  R/D/H― ― ― ― ―
1440

 
x
 
900/60 1
 
440
 
x
 
900 55.9  59.9  106.5  R/D/H ― ― ― ― ―
1600
 
x
 
900/50 1
 
600
 
x
 
900 46.4  49.9  96.5  R/D/H ― ― ― ― ―
1600
 
x
 
900/60 1
 
600
 
x
 
900 55.9  60.0  119.0  R/D/H
l―
l l l
1600
 
x
 
1200/50 1
 
600
 
x
 
1
 
200 61.8  49.9  131.5  R/D/H ― ― ― ― ―
1600
 
x
 
1200/60 1
 
600
 
x
 
1
 
200 75.0  60.0  162.0  R/D/H
l―
l l l
1680
 
x
 
1050/50 1
 
680
 
x
 
1
 
050 54.1  50.0  119.5  R/D/H ― ― ― ― ―
1680
 
x
 
1050/60 1
 
680
 
x
 
1
 
050 65.3  60.0  146.3  R/D/H ― ― ― ― ―
1920
 
x
 
1080/50 1
 
920
 
x
 
1
 
080 55.6  49.9  141.5  R/D/H ― ― ― ― ―
1920
 
x
 
1080/60 1
 
920
 
x
 
1
 
080
*366.6  59.9  138.5  R/D/H ― ― ― ― ―
1
 
920
 
x
 
1
 
080
*467.2  60.0  173.0  R ― ― ― ― ―
1920
 
x
 
1200/50 1
 
920
 
x
 
1
 
200 61.8  49.9  158.3  R/D/H ― ― ― ― ―
1920
 
x
 
1200/60 1
 
920
 
x
 
1
 
200
*474.6  59.9  193.3  R ― ― ― ― ―
1920
 
x
 
1200/60RB 1
 
920
 
x
 
1
 
200
*374.0  60.0  154.0  R/D/H
l―
l l l
*1 Signal with  l  in the plug and play column is a signal described in the EDID (extended display identification data) of the projector . The signal that 
does not have  l in the plug and play column can also be input if it is described in the\
 format column. The resolution may not be selected in the 
computer even if the projector is compatible for the signal that does no\
t have  l in the plug and play column.
*2
 
Pixel-Repetition signal (dot clock frequency 27.0
   MHz) only
*3
 
VESA
  CVT-RB (Reduced Blanking)-compliant
*4
 
Samples the pixels in the image processing circuit and projects the image.
Note
 f A signal with a different resolution is converted to the number of display dots. The number of display dots is as follows. g1
  920   x   1   200  
						

							Chapter 7 Appendix — Technical information
ENGLISH - 177
 fThe “i” at the end of the resolution indicates an interlaced signal. fWhen interlaced signals are connected, flickering may occur on the projected image. fDIGIT

AL LINK input compatible signal is the same as HDMI input compatible signal.  
						

							Chapter 7 Appendix — Specifications
178 - ENGLISH
Specifications
The specifications of the projector are as follows.
Power supplyPT- RZ575
100   V - 240   V ~ (100   V - 240   V alternating current), 50   Hz/60   Hz
PT- RZ575T110
  V ~ (110   V alternating current), 60   Hz
Power consumption PT
-

RZ575500
  W (5.9  
A
  - 2.3  
A)
PT
-

RZ575T500
  W (5.2  
A)
Power consumption (during 
standby) When [ST

ANDBY MODE] is set to [ECO]: approx. 0.5   W
When [STANDBY MODE] is set to [NORMAL]: approx. 10
  W
When [IN STANDBY MODE] in [AUDIO SETTING] is set to [ON], and the [QUICK STARTUP] function is 
disabled: approx. 22
  W
When the [QUICK STARTUP] function is enabled: approx. 50
  W
DLP chip Size
17
  mm (0.67") (aspect ratio 16:10)
Display system DLP chip x 1, DLP projection system
Number of pixels 2
  304   000 pixels (1   920   x   1   200 dots)
Lens Fixed: 0.8:1
Electric focus: F = 1.75, f = 11.9
  mm
Light source Laser
Light output 5
  000   lm
*1, 5 200 lm (center)*2
(Both values are measured when [OPERATING MODE] is set to [NORMAL].)
Contrast ratio
*120 000:1 (when [DYNAMIC CONTRAST] is set to [ON])
Color system 7 standards (NTSC/NTSC4.43/P
AL/PAL - N/PAL - M/SECAM/PAL60)
Projected image size 1.02
  m (40") to 7.62   m (300")
Image aspect ratio 16:10
Projection method [FRONT/REAR]/[FLOOR/CEILING]
Power cord length 3.0
  m (118-1/8")
Outer case Molded plastic
Dimensions Width
498
  mm (19-5/8")
Height 168
  mm (6-5/8") (with the feet at shortest position)
Depth 481
  mm (18-15/16") (including lens)
Weight Approx. 16.6
  k] (36.5   lbs.)
*3
Noise level*133 dB
Operating 
environment
Operating 
environment 
temperature0
  °C (32   °F) to 45   °C (113   °F)*4
Operating 
environment 
humidity10
  % to 80   % (no condensation)
Remote 
control Power supply
DC 3
  V (AAA/R03/LR03 battery x 2)
Operating range Within approx. 30
  m (98'5") (when operated directly in front of signal receiver)
Weight 102
  ] (3.6   ozs.) (including batteries)
Dimensions Width: 48
  mm (1-29/32"), Height: 145   mm (5-23/32"), Depth: 27   mm (1-1/16")
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21 1 18:2012 international standards.
*2  The value of the light output at the center region of the projected image is extracted based on the light output measurement method defined by the 
ISO/IEC 21
118:2012 international standards.
*3
 
A
 verage value. Weight varies for each product.
*4
 
The operating environment temperature should be between 0
   °C (32   °F) and 40   °C (104   °F) if the projector is used at an altitude between 1   400   m 
(4
  593') and 4   200   m (13   780') above sea level. When the [PROJECTOR SETUP] menu → [OPERATION SETTING]  → [OPERATING MODE] is set 
to [ECO], [SILENT], [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3], the projector cannot be used at an altitude of 2
  700   m (8   858') or higher above 
sea level.
When using the projector at an altitude lower than 2
  700   m (8   858') above sea level, and the operating environment temperature becomes 35   °C 
(95
  °F) or higher, the light output may be reduced to protect the projector. When using the projector at an altitude between 2   700   m (8   858') and 
4
  200   m (13   780'), and the operating environment temperature becomes 25   °C (77   °F) or higher, the light output may be reduced to protect the 
projector.
Note
 f The model numbers of accessories and optional accessories are subject to\
 change without prior notice.  
						

							Chapter 7 Appendix — Specifications
ENGLISH - 179
 rConnecting terminal
 terminal 1 set, high-density D - Sub 15   p (female)
RGB signal 0.7   V [p-p] 75   Ω (SYNC ON GREEN: 1.0   V [p-p] 75   Ω)
SYNC/HD TTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
YP
BPR signal Y: 1.0   V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
Y/C signal Y
: 1.0
 
V [p-p], C: 0.286
 
V [p-p] 75
 
Ω
 
terminal 1 set, high-density D
-
Sub 15
 
p (female)
RGB signal 0.7
 
V [p-p] 75
 
Ω (SYNC ON GREEN: 1.0
 
V [p-p] 75
 
Ω)
SYNC/HD TTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
YP
BPR signal Y: 1.0   V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
 terminal 1 set, DVI
-
D 24
 
p, single link, DVI 1.0 compliant, HDCP compatible
 terminal
 terminal Total 2 sets, HDMI 19
 
p, HDCP compatible, Deep Color compatible
Audio signal Linear PCM (sampling frequency: 48
 
kHz/44.1
 
kHz/32   kHz)
 terminal 1 set, pin jack, 1.0
 
V [p-p] 75
 
Ω
 terminal 1 set, pin jack x 2 (L-R), 0.5
 
V [rms], input impedance 22
 
kΩ or more
 terminal
 terminal Total 2 sets, M3 stereo mini jack, 0.5
 
V [rms], input impedance 22
 
kΩ or more
 
terminal 1 set, M3 stereo mini jack (monitor output, stereo compatible), 0
 
V [rms] to 1.80   V [rms] (variable), output 
impedance 2.2
 
kΩ or less
 terminal D
-
Sub 9
 
p, 1 set, RS
-
232C compliant, for computer control
 terminal 1 set, RJ
-
45, for network and DIGITAL LINK connections (HDBaseT
TM compliant), PJLink compatible, 
100Base
-
TX, Art-Net compatible, HDCP compatible, Deep Color compatible
 terminal 1 set, RJ
-
45, for network connection, PJLink compatible, 10Base
-
T/100Base - TX, Art-Net compatible
 terminal USB connector (type A) x 1, for power supply only (DC 5
 
V, maximum 900   mA)  
						

							Chapter 7 Appendix — Specifications
180 - ENGLISH
 rCompatible signal
For details of the types of video signals that can be used with the projector , refer to “List of compatible signals” 
(x   page   175).
Video input, Y/C input
Horizontal: 15.73
  kHz, Vertical: 59.94   Hz; Horizontal: 15.63   kHz, Vertical: 50   Hz
RGB input
 f Resolution: 640

  x   400 to 1   920   x   1   200
 fDot clock frequency: 162

  MHz or less
 fPIAS (Panasonic Intelligent 

Auto Scanning) system
YC
BCR/YPBPR input
 f Resolution: 480i/576i to 1

  920   x   1   080
 fDot clock frequency: 148.5

  MHz or less
 fThe HD/SYNC and VD terminals do not support 3 value SYNC.
DVI

-
D input
 f Moving image signal resolution: 480i*1/576i*1 to 1 920 x 1 080
Still image signal resolution: 640
 
x
 
400 to 1
 
920   x   1   200 (non-interlace)
 fDot clock frequency: 25

 
MHz to 162
 
MHz
HDMI input
 f Moving image signal resolution: 480i*1/576i*1 to 1 920 x 1 080
Still image signal resolution: 640
 
x
 
400 to 1
 
920   x   1   200 (non-interlace)
 fDot clock frequency: 25

 
MHz to 162
 
MHz
*1 Pixel-Repetition signal (dot clock frequency 27.0   MHz) only
Note
 fDIGITAL LINK input compatible signal is the same as HDMI input compatible signal.