Panasonic Projector PT-RZ575 User Manual

							Chapter 4 Settings — Menu navigation
ENGLISH - 61
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or control panel.
 fThe 

[MAIN MENU] screen is displayed.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
2) Press  as to select an item from the main menu.
 fThe selected item is highlighted in yellow

.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
3) Press the  button.
 fThe sub-menu items of the selected main menu are displayed.
0
POSITION
SHIFT
ASPECT
ZOOM
CLOCK PHASE
SCREEN ADJUSTMENT
MENU SELECT
SUB MENU DEFAULTENTER   
						

							Chapter 4 Settings — Menu navigation
62 - ENGLISH
4) Press as to select a sub-menu, and press qw or the  button to change or adjust settings.
 fSome items will switch in order as follows each time you press  qw

.
ABC
 fFor some items, press  qw to display an individual adjustment screen with a bar scale as shown be\
low.
0CONTRAST
ADJUST
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu.
Same operation is available by pressing the  button on the remote control.
 fSome items or functions may not be adjusted or used for certain signals to be input to the projector . When the items cannot be adjusted or 
used, the items in the menu screen are shown in black characters, and th\
ey cannot be adjusted or set.
If the item in the menu screen is displayed in black characters and the item cannot be adjusted or set, the factor causing it is displayed by 
pressing the  button while the corresponding menu is selected.
 f Some items can be adjusted even if signals are not input. fIndividual adjustment screen is cleared automatically if no operation is performed for approximately five seconds. fFor menu items, refer to “Main menu” (

x   page   62) and “Sub-menu” (x
  page   63).
 fThe cursor color depends on the setting in the [DISPLA

Y OPTION] menu → [ON-SCREEN DISPLAY] → [OSD DESIGN]. The selected item 
is displayed with the yellow cursor by the factory default.
 f In the portrait setting, the on-screen menu is displayed sideways.
T

o display the on-screen menu vertically, change the setting of the [DISPLAY OPTION] menu  → [ON-SCREEN DISPLAY] → [OSD 
ROTATION].
Resetting adjustment values to the factory default
If the  button on the remote control is pressed, the values adjusted in the menu items are restored to 
the factory default settings.
 button
1) Press the  button on the remote control.
0CONTRAST
ADJUST
Note
 fYou cannot reset all the settings to the factory default at a time. fT
o reset all the settings adjusted in the sub-menu item to the factory default one at a time, execute the [PROJECT OR SETUP] menu → 
[INITIALIZE].
 f Some items cannot be reset to the factory default settings even when the  button on the remote control is pressed. Adjust those 
items individually.
 f The triangular mark 

under the bar scale in the individual adjustment screen indicates the factory default setting. The position of the triangular 
mark varies according to the selected input signals.
Current adjustment value
Factory default setting
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a sub-menu sele\
ction screen.
Main menu item Page
[PICTURE] 66
[POSITION]72
[ADVANCED MENU]77   
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 63
Main menu itemPage
[DISPLAY LANGUAGE] 82
[DISPLAY OPTION]83
[PROJECTOR SETUP]100
[P IN P]121
[TEST PATTERN]123
[SIGNAL LIST]124
[SECURITY]127
[NETWORK]131
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can se\
t and adjust items in the sub-menu.
[PICTURE] 
Sub-menu itemFactory defaultPage
[PICTURE MODE] [GRAPHIC]
*166
[CONTRAST] [0]66
[BRIGHTNESS] [0]66
[COLOR] [0]
*267
[TINT] [0]67
[COLOR TEMPERATURE] [DEFAULT]
*267
[WHITE GAIN] [+10]68
[GAMMA] [DEFAULT]69
[DAYLIGHT VIEW] [AUTO]
*269
[SHARPNESS] [+6]
*269
[NOISE REDUCTION] [OFF]
*270
[DYNAMIC CONTRAST] [OFF]
*270
[SYSTEM SELECTOR] [AUTO]
*170
*1 Depends on the signal input.
*2  Depends on the [PICTURE MODE].
[POSITION] 
Sub-menu item Factory defaultPage
[SHIFT] ―72
[ASPECT] [DEFAULT]
*172
[ZOOM] ―73
[CLOCK PHASE] [0]
*174
[SCREEN ADJUSTMENT] [OFF]74
*1 Depends on the signal input.
[ADVANCED MENU] 
Sub-menu item Factory defaultPage
[DIGITAL CINEMA REALITY] [AUTO]
*177
[BLANKING] ―77
[INPUT RESOLUTION] ―78   
						

							Chapter 4 Settings — Menu navigation
64 - ENGLISH
Sub-menu itemFactory defaultPage
[CLAMP POSITION] [24]
*178
[EDGE BLENDING] [OFF]78
[FRAME RESPONSE] [NORMAL]80
[RASTER POSITION] ―81
*1 Depends on the signal input.
Note
 fThe factory default setting varies depending on the selected input termi\
nal.
[DISPLAY LANGUAGE] 
Details (x page 82)
[DISPLAY OPTION] 
Sub-menu item Factory defaultPage
[COLOR MATCHING] [OFF]83
[COLOR CORRECTION] [OFF]84
[SCREEN SETTING] ―84
[AUTO SIGNAL] [OFF]85
[AUTO SETUP] ―85
[BACKUP INPUT SETTING] ―86
[COMPUTER IN/OUT] ―87
[DVI-D IN] ―89
[HDMI IN] ―90
[DIGITAL LINK IN] ―91
[ON-SCREEN DISPLAY] ―93
[CLOSED CAPTION SETTING] ―95
[BACK COLOR] [BLUE]95
[STARTUP LOGO] [DEFAULT LOGO]96
[UNIFORMITY] ―96
[SHUTTER SETTING] ―97
[FREEZE] ―98
[WAVEFORM MONITOR] [OFF]98
[CUT OFF] ―99
[PROJECTOR SETUP] 
Sub-menu item Factory defaultPage
[PROJECTOR ID] [ALL]100
[PROJECTION METHOD] ―100
[ECO MANAGEMENT] ―101
[OPERATION SETTING] ―103
[LIGHT OUTPUT] [100.0%]107
[BRIGHTNESS CONTROL] ―107
[SCHEDULE] [OFF]111
[INITIAL STARTUP] [LAST MEMORY]11 3
[STARTUP INPUT SELECT] [LAST USED]11 4
[RS-232C] ―11 4
[FUNCTION BUTTON] ―11 5
[LENS CALIBRATION] ―11 5
[AUDIO SETTING] ―11 5
[STATUS] ―11 7
[DATE AND TIME] ―11 8
[SAVE ALL USER DATA] ―11 9   
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 65
Sub-menu itemFactory defaultPage
[LOAD ALL USER DATA] ―11 9
[INITIALIZE] ―11 9
[SERVICE PASSWORD] ―120
[P IN P] 
Details (x page 121)
[TEST PATTERN] 
Details (x page 123)
[SIGNAL LIST] 
Details (x page 124)
[SECURITY] 
Sub-menu item Factory defaultPage
[SECURITY PASSWORD] [OFF]127
[SECURITY PASSWORD CHANGE] ―127
[DISPLAY SETTING] [OFF]127
[TEXT CHANGE] ―128
[CONTROL DEVICE SETUP] ―128
[CONTROL DEVICE PASSWORD CHANGE] ―129
[NETWORK] 
Sub-menu item Factory defaultPage
[DIGITAL LINK MODE] [AUTO]131
[DIGITAL LINK STATUS] ―131
[NETWORK SETUP] ―132
[NETWORK CONTROL] ―132
[NETWORK STATUS] ―133
[DIGITAL LINK MENU] ―133
[Art-Net SETUP] [OFF]133
[Art-Net CHANNEL SETTING] [2]134
[Art-Net STATUS] ―134
Note
 fSome items may not be adjusted or used for certain signal formats to be input to the projector .
When the items cannot be adjusted or used, the items in the menu screen \
are shown in black characters, and they cannot be adjusted or 
set.
 f The factory default setting varies depending on the selected input termi\
nal.   
						

							Chapter 4 Settings — [PICTURE] menu
66 - ENGLISH
[PICTURE] menu
On the menu screen, select [PICTURE] from the main menu, and select an item from the sub-menu.
Refer to “Navigating through the menu” (x
  page   61) for the operation of the menu screen.
[PICTURE MODE]
You can switch to the desired picture mode suitable for the image source \
and the environment in which the 
projector is used.
1)
 
Press 
 as to select [PICTURE MODE].
2)
 
Press 
 qw or the  button.
 fThe 

[PICTURE MODE] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[STANDARD] The image becomes suitable for moving images in general.
[CINEMA] The image becomes suitable for movie contents.
[NATURAL] The image becomes sRGB compliant.
[REC709] The image becomes Rec.709 compliant when the setting other than [PICTURE MODE] is set to the 
factory default.
[DICOM SIM.] The image becomes similar to that of DICOM Part 14 Grayscale Standard.
[DYNAMIC] The light output is maximized for use in bright areas.
[GRAPHIC] The image becomes suitable for input from the personal computer.
Note
 fThe factory default picture mode is [GRAPHIC] for still image input signals and [ST ANDARD] for movie-based input signals. fRec.709 is an abbreviation of “ITU-R Recommendation BT
.709” and is a color standard of high-vision broadcasting.
 fDICOM is an abbreviation of “Digital Imaging and COmmunication in Medicine” and is a standard for medical imaging devices.  Although the 
DICOM name is used, the projector is not a medical device, and display images should not be used for medical purposes such as diagnosis.
[CONTRAST]
You can adjust the contrast of the colors.
1)
 
Press 
 as to select [CONTRAST].
2)
 
Press 
 qw or the  button.
 fThe 

[CONTRAST] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. The screen becomes brighter.
-31 - +31
Press q. The screen becomes darker.
Attention
 f
Adjust the [PICTURE] menu  → [BRIGHTNESS] first when you need to adjust the black level.
[BRIGHTNESS]
You can adjust the dark (black) part of the projected image.
1)
 
Press 
 as to select [BRIGHTNESS].
2)
 
Press 
 qw or the  button.
 fThe 

[BRIGHTNESS] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Increases the brightness of the dark (black) parts of the screen.
-31 - +31
Press q. Reduces the brightness of the dark (black) parts of the screen.   
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 67
[COLOR]
You can adjust the color saturation of the projected image.
1) 
Press 
 as to select [COLOR].
2)
 
Press 
 qw or the  button.
 fThe 

[COLOR] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Deepens colors.
-31 - +31
Press q. Weakens colors.
[TINT]
You can adjust the skin tone in the projected image.
1)
 
Press 
 as to select [TINT].
2)
 
Press 
 qw or the  button.
 fThe 

[TINT] individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.
Operation AdjustmentRange of adjustment
Press w. Adjusts skin tone toward greenish color.
-31 - +31
Press q. Adjusts skin tone toward reddish purple.
[COLOR TEMPERATURE]
You can switch the color temperature if the white areas of the projected \
image are bluish or reddish.
Adjusting with color temperature
1) Press 
as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Factory default setting.
[USER] Adjusts white balance as desired. Refer to “Adjusting desired white balance” (
x
  page   67) for 
details.
[LOW]/[HIGH] Select an item so that images become natural.
Note
 f[DEFAULT] cannot be selected when the [PICTURE] menu → [PICTURE MODE] is set to [DICOM SIM.]. fThe item is fixed to [USER] when the [DISPLA
Y OPTION] menu → [COLOR MATCHING] is set to anything other than [OFF].
Adjusting desired white balance
1) Press as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to select [USER].
4)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE] screen is displayed.   
						

							Chapter 4 Settings — [PICTURE] menu
68 - ENGLISH
5) Press as to select [WHITE BALANCE].
6)  
Press the  button.
 fThe 

[WHITE BALANCE] screen is displayed.
7)
 
Press 
 as to select [WHITE BALANCE HIGH] or [WHITE BALANCE LOW].
8)
 
Press the  button.
 fThe 

[WHITE BALANCE HIGH] screen or the [WHITE BALANCE LOW] screen is displayed.
9)
 
Press 
 as to select [RED], [GREEN], or [BLUE].
10)
 
Press 
 qw to adjust the level.
Item Operation Adjustment Range of adjustment
[RED] Press w.
Deepens red.
[WHITE BALANCE HIGH]: 0 - +255 (factory default is +255)
[WHITE BALANCE LOW]: 
-127 - +127 (factory default is 
0)
Press q.
Weakens red.
[GREEN] Press w.
Deepens green.
Press q. Weakens green.
[BLUE] Press w.
Deepens blue.
Press q. Weakens blue.
Note
 f
Adjust [COLOR  TEMPERATURE] correctly. All colors will not be displayed properly unless adequate adjustment is made. If the adjustment 
does not look suitable, you can press the  button on the remote control to return the setting for the selected item only to the 
factory default setting.
Changing the [USER] name
1) Press  as to select [COLOR TEMPERATURE].
2)  
Press 
 qw or the  button.
 fThe 

[COLOR TEMPERATURE] individual adjustment screen is displayed.
3)
 
Press 
 qw to select [USER].
4)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE] screen is displayed.
5)
 
Press 
 as to select [COLOR TEMPERATURE NAME CHANGE].
6)
 
Press the  button.
 fThe 

[COLOR TEMPERATURE NAME CHANGE] screen is displayed.
7)
 
Press 
 asqw to select the text, and press the  button to enter the text.
8)
 
Press 
 asqw to select [OK], and press the  button.
 fThe name set to color temperature is changed.
Note
 f When a name is changed, display of [USER] is also changed.
[WHITE GAIN]
Adjust the brightness of the white part of the image.
1)
 
Press 
 as to select [WHITE GAIN].
2)
 
Press 
 qw or the  button.
 fThe 

[WHITE GAIN]  individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.   
						

							Chapter 4 Settings — [PICTURE] menu
ENGLISH - 69
OperationAdjustmentRange of adjustment
Press w. Brightness of the white part gets stronger.
0 - +10
Press q. The image becomes more natural.
[GAMMA]
You can switch gamma mode.
1)
 
Press 
 as to select [GAMMA].
2)
 
Press 
 qw or the  button.
 fThe 

[GAMMA] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[DEFAULT] Factory default setting.
[1.8] Set so that images become as you like.
[2.0]
[2.2]
Note
 f In the following conditions, the [DEF AULT] setting is disabled even when it is selected, and the same gamma mode as when [2.2] is set is 
applied.
 g When the [ADV

ANCED MENU] menu → [EDGE BLENDING] is set to anything other than [OFF]
 gWhen the levels of [WHITE], [RED], [GREEN], and [BLUE] are adjusted from the [DISPLA Y

 OPTION] menu → [UNIFORMITY]
 gWhen the [DISPLA

Y OPTION] menu → [UNIFORMITY]  → [PC CORRECTION] is set to [ON]
[DAYLIGHT VIEW]
You can correct the image to the optimal vividness even if it is projecte\
d under a bright light.
1)
 
Press 
 as to select [DAYLIGHT VIEW].
2)
 
Press 
 qw or the  button.
 fThe 

[DAYLIGHT VIEW] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[AUTO] Detects the brightness of the installed environment by the luminance sen\
sor, and automatically 
corrects the vividness of the image.
[OFF] No correction.
[1] Corrects the image to weaken vividness.
[2] Corrects the image to medium vividness.
[3] Corrects the image to high vividness.
Note
 f[AUTO] cannot be selected when the [ADVANCED MENU] menu  → [EDGE BLENDING] is set to [ON] or [USER]. f[AUT
O] cannot be selected when the [PROJECTOR SETUP] menu → [FRONT/REAR] of [PROJECTION METHOD] is set to [REAR].
 fThe luminance may not be detected correctly when an object is placed on top of the projector , blocking the luminance sensor

. In such a 
case, this function may not operate properly even if it is set to [AUT O].
 fThe factory default setting is [OFF] when the [PICTURE] menu 

→ [PICTURE MODE] is set to [NATURAL], [REC709], or [DICOM SIM.]. In 
this case, [AUTO] cannot be selected.
[SHARPNESS]
You can adjust the sharpness of the projected image.
1)
 
Press 
 as to select [SHARPNESS].
2)
 
Press 
 qw or the  button.
 fThe 

[SHARPNESS]  individual adjustment screen is displayed.
3)
 
Press 
 qw to adjust the level.   
						

							Chapter 4 Settings — [PICTURE] menu
70 - ENGLISH
OperationAdjustmentRange of adjustment
Press w. Contours become sharper.
0 - +15
Press q. Contours become softer.
Note
 f
If you press  w while the adjustment value is [+15], the value will become [0]. If you press  q while the adjustment value is [0], the value will 
become [+15].
[NOISE REDUCTION]
You can reduce noises when the input image is degraded and noise is occur\
ring in the image signal.
1)
 
Press 
 as to select [NOISE REDUCTION].
2)
 
Press 
 qw or the  button.
 fThe 

[NOISE REDUCTION] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] No correction.
[1] Slightly corrects the noise.
[2] Moderately corrects the noise.
[3] Strongly corrects the noise.
Attention
 fWhen this is set for an input signal with less noise, the image may look dif ferent from the original image. In such a case, set it to [OFF].
[DYNAMIC CONTRAST]
Light adjustment of the light source is performed automatically according to the image to make the contrast 
optimum for the image.
1)
 
Press 
 as to select [DYNAMIC CONTRAST].
2)
 
Press 
 qw or the  button.
 fThe 

[DYNAMIC CONTRAST] individual adjustment screen is displayed.
3)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the dynamic contrast function.
[ON] Executes the light adjustment of the light source.
Note
 fThe brightness control function and the dynamic contrast function will o\
perate simultaneously , but the dynamic contrast function will not 
operate while measuring the brightness and the color.
[SYSTEM SELECTOR]
The projector will automatically detect the input signal, but you can se\
t the system method manually when an 
unstable signal is input. Set the system method matching the input signal.
1)
 
Press 
 as to select [SYSTEM SELECTOR].
2)
 
Press the  button.
3)

 
Press 
 as to select a system format.
 fA

vailable system formats vary depending on the input signal.
Terminal System format
 terminal, 
 terminal
*1
Select [AUTO], [NTSC], [NTSC4.43], [PAL], [PAL-M], [PAL-N], [SECAM], or [PAL60].
Select [AUT O] normally. ([AUTO] will automatically determine from [NTSC], [NTSC4.43], [PAL], 
[PAL
- M], [PAL - N], [SECAM], or [PAL60].)
Switch the setting to the appropriate TV signal format.