Panasonic Projector PT-RZ970 User Manual

							ENGLISH - 11
Read this first!
CAUTION:
 rPOWER
When disconnecting the power cord, be sure to hold the power plug and power connector
.
If the power cord itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric shocks 
will result.
When not using the projector for an extended period of time, disconnect the power plug from the wall 
outlet.
Failure to do so may result in fire or electric shock.
Before replacing the projection lens, be sure to turn off the power and disconnect the power plug from 
the wall outlet.
 f Unexpected projection of light may cause injury to eyes.
 fReplacing the projection lens without removing the power plug may result in electric shock.
Disconnect the power plug from the wall outlet before carrying out any c\
leaning.
Failure to do so may result in electric shock.
 r ON USE/INSTALLATION
Do not place heavy objects on top of the projector.
Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or 
injury. The projector will be damaged or deformed.
Do not put your weight on this projector.
You could fall or the projector could break, and injury will result.
 fBe especially careful not to let young children stand or sit on the projector
.
Do not place the projector in extremely hot locations.
Doing so will cause the outer casing or internal components to deteriorate, or result in fire.
 f T

ake particular care in locations exposed to direct sunlight or near heaters.
Do not place your hands in the openings beside the optical lens, while shifting the lens.
Failure to observe this could cause injury.
Do not install the projector in a location where salt pollution or corro\
sive gas may occur.
Doing so may result in falling due to corrosion. Also, it may result in malfunctions.
Do not stand in front of the lens while the projector is being used.
Doing so can cause damage and burns to clothing.
 f Strong light is emitted from the projector

’s lens.
Do not place objects in front of the lens while the projector is being u\
sed.
Doing so can cause fire, damage to an object, or malfunction of the projector .
 fStrong light is emitted from the projector

’s lens.
Always disconnect all cables before moving the projector.
Moving the projector with cables still attached can damage the cables, which will cause fire or electric shocks to 
occur.
When mounting the projector on the ceiling, keep mounting screws and power cord from contact with 
metal parts inside the ceiling.
Contact with metal parts inside the ceiling can cause electric shocks.
 r ACCESSORIES
When not using the projector for an extended period of time, remove the batteries from the remote 
control.
Failure to observe this will cause the batteries to leak, overheat, catch fire or explode, which may result in fire or 
contamination of surrounding area.
 rMAINTENANCE
Ask your dealer about cleaning inside the projector every 20 000 hours o\
f usage as an estimated 
duration.
Continuous use while dust is accumulated inside the projector may result in fire.
 fFor cleaning fee, ask your dealer

.  
						

							12 - ENGLISH
Read this first!
To remove the battery
Remote Control Battery
1.
 P
 ress the guide and lift the cover.
(ii)(i)
2. Remove the batteries.  
						

							ENGLISH - 13
Read this first!
Brazil Only
Brasil Apenas
 rManuseio de baterias usadas
BRASIL
Após o uso, as pilhas e/ou baterias deverão 
ser entregues ao estabelecimento comercial 
ou rede de assistência técnica autorizada.
Cobrir os terminais positivo (+) e negativo (-) com uma fita isolante adesiva, antes de depositar numa caixa 
destinada para o recolhimento. O contato entre partes metálicas pode causar vazamentos, gerar calor , romper 
a blindagem e produzir fogo. (Fig. 1)
Fig. 1
Como isolar os terminais
Não desmonte, não remova o invólucro, nem amasse a bateria. O gás liberado pela bateria pode irritar a 
garganta, danificar o lacre do invólucro ou o vazamento provocar calor , ruptura da blindagem e produzir fogo 
devido ao curto circuito dos terminais. Não incinere nem aqueça as baterias, elas não podem ficar expostas a 
temperaturas superiores a 100
  °C (212   °F). O gás liberado pela bateria pode irritar a garganta, danificar o lacre 
do invólucro ou o vazamento provocar calor, ruptura da blindagem e produzir fogo devido ao curto circuito dos 
terminais provocado internamente.
Evite o contato com o liquido que vazar das baterias. Caso isto ocorra, lave bem a parte afetada com bastante 
água. Caso haja irritação, consulte um médico.
 r Remoção das baterias
1. Pressione a guia e levante a tampa.
(ii)(i)
2. Remova as baterias.
Fita Isolante
Fita Isolante  
						

							 
14 - ENGLISH
 rTrademarks
 fSOLID SHINE is a trademark of Panasonic Corporation.
 fWindows, Internet Explorer

, and Microsoft Edge are registered trademarks or trademarks of Microsoft 
Corporation in the United States and other countries.
 f Mac, Mac OS, and Safari are trademarks of 

Apple Inc., registered in the United States and other countries.
 fPJLinkTM is a registered trademark or pending trademark in Japan, the United States, and other countries and 
regions.
 f HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of 
HDMI Licensing LLC in the United States and other countries.
 fRoomV

iew and Crestron RoomView are registered trademarks of Crestron Electronics, Inc.
Crestron Connected
TM and Fusion RV are trademarks of Crestron Electronics, Inc.
 f HDBaseTTM is a trademark of HDBaseT Alliance.
 fArt-NetTM Designed by and Copyright Artistic Licence Holdings Ltd
 fAdobe, 

Adobe Flash Player, and Adobe Reader are trademarks or registered trademarks of Adobe Systems Inc. 
in the United States and/or other countries.
 f Some of the fonts used in the on-screen menu are Ricoh bitmap fonts, which are manufactured and sold by 
Ricoh Company

, Ltd.
 fAll other names, company names, and product names mentioned in this manual are trademarks or registered 
trademarks of their respective owners.
Please note that the 
® and TM symbols are not specified in this manual.
 r Illustrations in this manual
 fIllustrations of the projector , screen, and other parts may vary from the actual product.
 fIllustrations of the projector with the power cord attached are only examples.  The shape of the supplied power 
cords varies depending on the country where you purchased the product.
 r Reference pages
 fReference pages in this manual are indicated as ( x  page 00).
 rTerm
 fIn this manual, the “Wireless/wired remote control unit” accessory is referred to as “Remote control”.   
						

							 
ENGLISH - 15
Features of the Projector
High luminance and high contrast
 /£With a unique optical system which uses 
a new-generation laser light source, and 
the laser light source drive system, high 
luminance of 10
  000   lm
*1 and high contrast 
of 10
 
000:1 are achieved even with its 
compact size.
*1 A value for PT- RX110. A value for PT- RZ970 and PT- RW930 
is 9   400   lm.
Easy and highly flexible setup
 /£Easy and flexible setup is achieved by 
compatibility with DIGIT
AL LINK and Art-
Net, standard support of 3G
- SDI (only for 
PT
-

RZ970), standard support of geometric 
adjustment function, 360° installation 
support including horizontal, vertical, and 
portrait utilizing the characteristics of solid-
state light source, and a lineup of various 
optional lenses.
Long life and high reliability
 /£ The maintenance cost for long-term 
operation is reduced by the unique light 
source cooling control technology and 
improvement of the dust resistance. 
Also, 
it will contribute to the stable operation by 
implementation of the backup function that 
will continue the projection by switching to 
the backup input signal immediately even 
when the input signal is discontinued, in 
addition to adopting solid-state light source 
which has long life.
Quick Steps
For details, refer to the corresponding pages.
1. Set up the projector .
(x   page   32)
2. Connect with external devices.
(x   page   50)
3. Connect the power cord.
(x   page   57)
4. Switch on the projector .
(x   page   58)
5. Make initial settings.
(x   page   59)
 fTake this step when you switch on the 
power for the first time after purchasing the 
projector.
6. Select the input signal.
(
x   page   68)
7. Adjust the image.
(x   page   69)   
						

							16 - ENGLISH
Chapter 1 Preparation
This chapter describes things you need to know or check before using the projector.  
						

							Chapter 1 Preparation — Precautions for use
ENGLISH - 17
Precautions for use
Cautions when transporting
 fIf you purchased the projector with the standard zoom lens, remove the lens protection material before use, and 
store it for the future use. Move the lens position to the home position and attach the lens protection material 
when transporting.
If you purchased the projector with the lens sold separately
, remove the lens hole cover before use, and store it 
for the future use. Move the lens position to the home position, remove the projection lens, and attach the lens 
hole cover when transporting.
For the steps to move the lens position to the home position, refer to “Setting the lens position” ( x
  page   70).
Lens hole cover
Lens protection material
 f Hold the bottom of the projector and do not hold the projection lens or the opening around the projection 
lens when transporting. Failure to do so may cause damage. 
Also, handle the projector in a way not to apply 
excessive vibration or shock. Failure to do so may cause a failure due to the damaged internal components.
 f Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.
Cautions when installing
 r After attaching the projection lens, be sure to attach the Lens Mount Cover .
Not doing so may cause failure due to accumulating dust internally.
 rDo not set up the projector outdoors.
The projector is designed for indoor use only.
 rDo not set up the projector in the following locations.
 fPlaces where vibration and impacts occur such as in a car or vehicle: Doing so may cause damage to internal 
components or malfunction.
 fLocation close to sea or where corrosive gas may occur: 

The projector may fall due to corrosion. Also, failure to 
do so may shorten the life of the components and result in malfunction.
 f Near the exhaust of an air conditioner: Depending on the conditions of use, the screen may fluctuate in rare 
cases due to the heated air from the air exhaust port or the hot or cooled air from the air conditioner . Make sure 
that the exhaust from the projector or other equipment, or the air from the air conditioner does not blow toward 
the front of the projector

.
 fPlaces with sharp temperature fluctuations such as near lights (studio lamps): Doing so may shorten the life of 
the light source, or result in deformation of the projector due to heat, which may cause malfunctions.
Follow the operating environment temperature of the projector

.
 fNear high-voltage power lines or near motors: Doing so may interfere with the operation of the projector .
 fPlaces where there is high-power laser equipment: Directing a laser beam onto the projection lens surface 
causes damage to the DLP

 chips.   
						

							Chapter 1 Preparation — Precautions for use
18 - ENGLISH
 rBe sure to ask a specialized technician or your dealer when installing t\
he projector on 
a ceiling.
The optional Ceiling Mount Bracket is required.
Model No.: ET
-

PKD120H (for High Ceilings), ET
-
 PKD120S (for Low Ceilings), ET
-
 PKD130H (for High Ceilings, 
6-axis Adjustment), ET
-

PKD130B (Projector Mount Bracket)
 rAsk a qualified technician or your dealer to install the cable wiring for DIGIT AL  LINK 
connection.
Image and sound may be disrupted if cable transmission characteristics cannot be obtained due to inadequate 
installation.
 r The projector may not work properly due to strong radio wave from the br\
oadcast 
station or the radio.
If there is any facility or equipment which outputs strong radio waves near the installation location, install the 
projector at a location sufficiently far from the source of the radio waves. Or , wrap the LAN cable connected to the 
 terminal using a piece of metal foil or a metal pipe which is grounded at both ends.
 r Focus adjustment
The high clarity projection lens is thermally affected by the light from the light source, making the focus unstable in 
the period just after switching on the power. It is recommended that images be projected continuously for at least 
30 minutes before the focus is adjusted.
 rDo not install the projector at an altitude of 4   200   m (13   780') or higher above sea level.
 rDo not use the projector in a location that the ambient temperature exce\
eds 45

  °C 
(113
  °F).
Using the projector in a location that the altitude is too high or the ambient temperature is too high may reduce the 
life of the components or result in malfunctions.
 rProjection in all 360° direction is possible.
360°360°
360°
360° vertically 360° horizontally 360° tilted
(combination of vertical and horizontal)
 r The geometric adjustment function is disabled when projecting the input \
signal 
rotated by 90°. (Only for PT
‑RW930, PT‑RX110)
The geometric adjustment function cannot be used when projecting the input signal rotated by 90°. When 
installing the projector, follow the following instructions to prevent distortion in the projected image.
 fUse a flat screen.
 fInstall the projector so that the front side of the projector is parallel to the screen.
 fInstall the projector so that the image can be projected within the range of shift adjustment by moving the lens 
position.
The 90° rotation of the image can be set in the [DISPLA

Y OPTION] menu → [IMAGE ROTATION].   
						

							Chapter 1 Preparation — Precautions for use
ENGLISH - 19
 rCautions when setting up the projector
 fThe projector can be used by installing its top placed on the floor .  To prevent the top surface from getting 
scratched during use, it is recommended to attach about a 20   mm (25/32") square buffer material (such as 
rubber cushion) on the four corners of the top surface.
Buffer material
Buffer materialFloor
 f
Use the adjustable feet only for the floor standing installation and for adjusting the angle. Using them for other 
purposes may damage the projector
.
 fWhen installing the projector with a method other than the floor installation using the adjustable feet, top placed 
on the floor

, or the ceiling installation, use the five screw holes for ceiling mount (as shown in the figure) to fix 
the projector to the mount.
(Screw diameter: M6, tapping depth inside the projector: 12
  mm (15/32"), torque: 4 ± 0.5   N·m)
In such case, make sure that there is no clearance between the screw holes for ceiling mount on the projector 
bottom and the setting surface by inserting spacers (metallic) between them.
Screw holes for ceiling mount (M6)
Adjustable feet Adjustable feet
Positions of screw holes for ceiling mount and adjustable feet
 f Do not stack projectors on top of each other .
 fDo not block the ventilation ports (intake and exhaust) of the projector .   
						

							Chapter 1 Preparation — Precautions for use
20 - ENGLISH
 fPrevent hot and cool air from the air conditioning system to blow directly to the ventilation ports (intake and 
exhaust) of the projector
.
100 mm (3-15/16) or longer
500 mm (19-11/16) or longer 500 mm (19-11/16) or longer
500 mm (19-11/16) or longer
 f Do not install the projector in a confined space.
When installing the projector in a confined space, provide air conditioning or ventilation separately . Exhaust heat 
may accumulate when the ventilation is not enough, triggering the protection circuit of the projector .
Security
When using this product, take safety measures against the following incidents.
 fPersonal information being leaked via this product
 fUnauthorized operation of this product by a malicious third party
 fInterfering or stopping of this product by a malicious third party
T

ake sufficient security measures.
 f Make your password difficult to guess as much as possible.
 fChange your password periodically

. A password can be set in the [SECURITY] menu  → [SECURITY 
PASSWORD CHANGE].
 f Panasonic Corporation or its affiliate companies will never ask for your password directly . Do not divulge your 
password in case you receive such inquiries.
 f The connecting network must be secured by a firewall, etc.
 fSet a password for the web control and restrict the users who can log in.  A

 password for the web control can be 
set in the [Change password] page of the web control screen.
DIGITAL LINK
“DIGITAL LINK” is a technology to transmit the video, audio, Ethernet, and serial control signals using a twisted 
pair cable by adding unique functions by Panasonic to the HDBaseTTM communication standard formulated by 
HDBaseT Alliance.
This projector supports the optional Panasonic DIGITAL LINK output supported device (Model No.: ET
-

YFB100G, 
ET
-

YFB200G) and peripheral devices by other manufacturers (twisted-pair-cable transmitters such as the 
“XTP transmitter” of Extron Electronics) that use the same HDBaseT
TM standard. For the devices of other 
manufacturers that the operation has been verified with this projector , visit the Panasonic website (http://
panasonic.net/avc/projector/). Note that the verification for devices of other manufacturers has been made for the 
items set by Panasonic Corporation, and not all the operations have been verified. For operation or performance 
problems caused by the devices of other manufacturers, contact the respective manufacturers.  This projector 
does not support audio transmission because it is not equipped with audio function.