Panasonic Projector PT-RZ970 User Manual

							Chapter 3 Basic Operations — Projecting
ENGLISH - 71
Adjustment range by the lens position shift (optical shift)
Perform the lens position shift within the adjustment range.
The focus may change when the lens position is shifted out of the adjustment range. This is because the shift 
of the lens is restricted to protect the optical parts. Projection position can be adjusted with the optical axis shift 
function based on the position of the projected screen in the home position (standard projection position).
Lens type Zoom Lens
Standard zoom lens, ET‑DLE150, ET‑DLE250,  ET‑DLE350, ET‑DLE450 ET-
DLE085
PT
-

RZ970
Standard projection position
Projected image height V
Projected image width H
0.5 V
0.16 V
0.1 H 0.3 H
0.1 H
Standard projection position
Projected image height V
Projected image width H
0.5 V
0.16 V
0.1 H 0.28 H
PT-
RW930
Standard projection position
Projected image height V
Projected image width H
0.6 V
0.16 V
0.1 H 0.3 H
0.1 H
Standard projection position
Projected image height V
Projected image width H
0.6 V
0.16 V
0.1 H 0.28 H
PT-
RX110
Standard projection position
Projected image height V
Projected image width H
0.5 V
0.13 V
0.1 H 0.3 H
0.1 H
Standard projection position
Projected image height V
Projected image width H
0.45 V
0.13 V
0.1 H 0.28 H
Note
 f
When the optional Fixed-focus Lens (Model No.: ET- DLE055) is attached, do not use the shift adjustment, and use the projector with the 
lens position at the home position.
 f When the optional Fixed-focus Lens (Model No.: ET-

DLE030) is attached, it can be used with the shift adjustment based on the projected 
image position in the lens standard position within the range that the edge of the projected image is not blocked by the projector body .   
						

							Chapter 3 Basic Operations — Operating with the remote control
72 - ENGLISH
Operating with the remote control
Using the shutter function
If the projector is not used for a certain period of time during the meeting intermission, for example, it is possible 
to turn off the image temporarily.
 button
1) Press the  button.
 fThe image disappears.
 fThis operation can be also performed using the  button on the control panel.
2)

 
Press the  button again.
 fThe image is displayed.
Note
 f The power indicator  will blink slowly in green while the shutter function is in use (shutter: closed). fThe fade-in/fade-out time of the image can be set by the [DISPLA Y
 OPTION] menu → [SHUTTER SETTING].
 fThe light source may be lit dimly due to warm up when the shutter function is used in the operating environment temperature of around 0

  °C 
(32
  °F).
Using the on-screen display function
Turn off the on-screen display function (no display) when you do not wish the viewers to see the on-screen 
display, such as the menu or the input terminal name.
 button
1) Press the  button.
 fT

urns off (hides) the on-screen display.
2)
 
Press the  button again.
 fCancels the hide condition of the on-screen display

.
Note
 f The hide condition of the on-screen display can also be canceled by pressing the  button on the control panel for at least three 
seconds while the on-screen display is of
f (hidden).   
						

							Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 73
Using the automatic setup function
The image position when the DVI-D/HDMI signal is input, or the resolution, clock phase, and image position when 
the analog RGB signal is input can be adjusted automatically . (Analog RGB signal is a signal structured with dots 
just like the computer signal.)
It is recommended to input an image with bright white borders at the edges and high-contrast black and white 
characters when the automatic adjustment is being performed.
Avoid using images that include halftones or gradation, such as photographs and computer graphics.
 button
1) Press the  button.
 f[COMPLETE] is displayed when it has completed without any problem.
 fThis operation can be also performed by pressing the  button on the control panel.
Note
 f The clock phase may shift even if it has completed without any incident. In such a case, adjust the [POSITION] menu  →  [CLOCK PHASE] 
(x   page   91).
 fIf an image with blurred edges or a dark image is input, [INCOMPLETE] may appear or adjustment may not be performed properly even 
when [COMPLETE] appears. In such a case, adjust the following settings.
 g[ADV

ANCED MENU] menu → [INPUT RESOLUTION] ( x
  page   95)
 g[POSITION] menu  →

 [CLOCK PHASE] (x   page   91)
 g[POSITION] menu  →

 [SHIFT] (x
  page   89)
 fAdjust special signals according to the [DISPLA

Y OPTION] menu → [AUTO SETUP] ( x
  page   102).
 fAutomatic adjustment may not be possible depending on the computer model. fAutomatic adjustment may not be possible for the synchronization signal for composite sync or SYNC ON GREEN. fImage may be disrupted for a few seconds during automatic adjustment, but this is not a malfunction. fAdjustment is required for each input signal. fAutomatic adjustment can be canceled by pressing the  button during the automatic adjustment operation. fEven if a signal possible to perform the automatic setup is being input, it may not be able to adjust correctly if the automatic setup function 
is used while the moving image is being input. [INCOMPLETE] may be displayed, or the adjustment may not be completed correctly even if 
[COMPLETE] is displayed.
Using the function button
By assigning the following functions to the  button, it can be used as a simplified shortcut button.
[P IN P], [SUB MEMORY], [SYSTEM SELECTOR], [SYSTEM DAYLIGHT VIEW], [FREEZE], [WAVEFORM 
MONITOR], [ASPECT], [PROJECTION METHOD]
 button
1) Press the  button.
Note
 f Assignment of the function is performed from the [PROJECT OR SETUP] menu → [FUNCTION BUTTON] (x   page   137).
Displaying internal test pattern
The projector has eight types of internal test patterns to check the condition of the projector body. To display test 
patterns, perform the following steps.
 button
1) Press the  button.
2)  
Press 
 qw to select the test pattern.
Note
 f Test patterns can also be displayed using the menu operation. Refer to “[TEST PATTERN] menu” (x   page   143) for details. fSettings of position, size, and other factors will not be reflected in test patterns. Make sure to display the input signal before performing 
various adjustments.   
						

							Chapter 3 Basic Operations — Operating with the remote control
74 - ENGLISH
Using the status function
Display the status of the projector.
 button
1) Press the  button.
 fThe 

[STATUS] screen is displayed.
100000h
100000h / 100000h
1.00 / 1.00
1/4
31°C/87°F27°C/80°F31°C/87°F31°C/87°F31°C/87°F
1013hPa
MENUEXIT
CHANGEENTERSEND E-MAIL
SELF TEST
ATMOSPHERIC PRESSUREAUTO - FLOOR
NO ERRORSCOOLING CONDITION LIGHT2 TEMP. LIGHT1 TEMP. EXHAUST AIR TEMP. OPTICS MODULE TEMP. INTAKE AIR TEMP. MAIN/SUB VERSION LIGHT RUNTIME PROJECTOR RUNTIME PROJECTOR TYPE
RZ970(123456789012)STATUS
Note
 f The projector status can also be displayed using the menu operation. Refer to the [PROJECT OR SETUP] menu  → [STATUS] 
(x   page   138) for details.
Setting ID number of the remote control
When you use the multiple projectors together, you can operate all the projectors simultaneously or each projector 
individually using a single remote control, if a unique ID number is assigned to each projector .
After setting the ID number of the projector, set same ID number on the remote control.
The factory default ID number of the projector is set to [ALL]. When using a single projector , keep 
pressing the  button on the remote control for at least three se\
conds to set the ID number of 
the remote control to [ALL]. In addition, when the ID number of the projector is unknown, setting the ID 
number to [ALL] enables the remote control.
 button
1) Press the  button on the remote control.
2)  
W
 ithin five seconds, press the two ‑ digit ID number set on the projector using the number (  ‑  ) 
buttons.
 f When the ID number is set to [ALL], you can control the projector regardless of the ID number setting of the 
projector

.
Attention
 f Since the ID number of the remote control can be set without the projector body , do not press the  button on the remote control 
carelessly . If the  button is pressed and no number ( - ) buttons are pressed within five seconds, the ID number returns to 
its original value before the  button was pressed.
 f The ID number set on the remote control will be stored unless it is set again. However , it will be erased if the remote control is left with dead 
batteries. Set the same ID number again when the batteries are replaced.
Note
 f When the ID number of the remote control is set to [0], you can control the projector regardless of the ID number setting of the projector 
body
, as same as when [ALL] is set.
 fSet the ID number of the projector body from the [PROJECT

OR SETUP] menu → [PROJECTOR ID].   
						

							ENGLISH - 75
Chapter 4 Settings
This chapter describes the settings and adjustments you can make using the on-screen menu. 
						

							Chapter 4 Settings — Menu navigation
76 - ENGLISH
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or control panel.
 fThe 

[MAIN MENU] screen is displayed.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
2) Press  as to select an item from the main menu.
 fThe selected item is highlighted in yellow

.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
3) Press the  button.
 fThe sub-menu items of the selected main menu are displayed.
0
POSITION
SHIFT
ASPECT
ZOOM
GEOMETRY CLOCK PHASE
MENU SELECT
SUB MENU DEFAULT
ENTER
OFF  
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 77
4) Press as to select a sub ‑ menu, and press qw or the  button to change or adjust settings.
 fSome items will switch in order as follows each time you press  qw

.
ABC
 fFor some items, press  qw to display an individual adjustment screen with a bar scale as shown below .
0CONTRAST
ADJUST
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu. fSome items or functions may not be adjusted or used for certain signals to be input to the projector . When the items cannot be adjusted or 
used, the items in the menu screen are shown in black characters, and they cannot be adjusted or set.
If the item in the menu screen is displayed in black characters and the item cannot be adjusted or set, the factor causing it is displayed by 
pressing the  button while the corresponding menu is selected.
 f Some items can be adjusted even if signals are not input. fIndividual adjustment screen is cleared automatically if no operation is performed for approximately five seconds. fFor menu items, refer to “Main menu” (

x   page   77) and “Sub-menu” (x
  page   78).
 fThe cursor color depends on the setting in the [DISPLA

Y OPTION] menu → [ON-SCREEN DISPLAY] → [OSD DESIGN]. The selected item 
is displayed with the yellow cursor by the factory default.
 f In the portrait setting, the on-screen menu is displayed sideways.
T

o display the on-screen menu vertically, change the setting of the [DISPLAY OPTION] menu  → [ON-SCREEN DISPLAY] → [OSD 
ROTATION].
Resetting adjustment values to the factory default
If the  button on the remote control is pressed, the values adjusted in the menu items are restored to 
the factory default settings.
 button
1) Press the  button on the remote control.
0CONTRAST
ADJUST
Note
 fYou cannot reset all the settings to the factory default at a time. fT
o reset all the settings adjusted in the sub-menu item to the factory default one at a time, execute the [PROJECT OR SETUP] menu → 
[INITIALIZE].
 f Some items cannot be reset to the factory default settings even when the  button on the remote control is pressed. Adjust those 
items individually.
 f The triangular mark 

under the bar scale in the individual adjustment screen indicates the factory default setting. The position of the triangular 
mark varies according to the selected input signals.
Current adjustment value
Factory default setting
Main menu
The following items are in the main menu.
When a main menu item is selected, the screen changes to a sub-menu selection screen.
Main menu item Page
[PICTURE] 81
[POSITION]89
[ADVANCED MENU]94
[DISPLAY LANGUAGE]99  
						

							Chapter 4 Settings — Menu navigation
78 - ENGLISH
Main menu itemPage
[DISPLAY OPTION] 100
[PROJECTOR SETUP] 11 9
[P IN P]141
[TEST PATTERN]143
[SIGNAL LIST]144
[SECURITY]147
[NETWORK]151
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can set and adjust items in the sub-menu.
[PICTURE] 
Sub-menu itemFactory defaultPage
[PICTURE MODE] [GRAPHIC]
*181
[CONTRAST] [0]81
[BRIGHTNESS] [0]81
[COLOR] [0]
*282
[TINT] [0]82
[COLOR TEMPERATURE] [DEFAULT]
*282
[WHITE GAIN] [+10]84
[GAMMA] [DEFAULT]84
[SYSTEM DAYLIGHT VIEW] [OFF]
*285
[SHARPNESS] [+6]
*285
[NOISE REDUCTION] [OFF]
*286
[DYNAMIC CONTRAST] [2]
*286
[SYSTEM SELECTOR] [YP
BPR]*187
*1 Depends on the signal input.
*2  Depends on the [PICTURE MODE].
[POSITION] 
Sub-menu item Factory defaultPage
[SHIFT] ―89
[ASPECT] [DEFAULT]
*189
[ZOOM] ―90
[CLOCK PHASE] [0]
*191
[GEOMETRY] [OFF]91
*1 Depends on the signal input.
[ADVANCED MENU] 
Sub-menu item Factory defaultPage
[DIGITAL CINEMA REALITY] [AUTO]
*194
[BLANKING] ―94
[INPUT RESOLUTION] ―95
[CLAMP POSITION] [24]
*195
[EDGE BLENDING] [OFF]95  
						

							Chapter 4 Settings — Menu navigation
ENGLISH - 79
Sub-menu itemFactory defaultPage
[FRAME RESPONSE] [NORMAL]97
[RASTER POSITION] ―98
*1 Depends on the signal input.
Note
 fThe factory default setting varies depending on the selected input terminal.
[DISPLAY LANGUAGE] 
Details (x page 99)
[DISPLAY OPTION] 
Sub-menu item Factory defaultPage
[COLOR MATCHING] [OFF]100
[COLOR CORRECTION] [OFF]101
[SCREEN SETTING] ―101
[AUTO SIGNAL] [OFF]102
[AUTO SETUP] ―102
[BACKUP INPUT SETTING] ―103
[RGB IN] ―104
[DVI-D IN] ―105
[HDMI IN] ―107
[DIGITAL LINK IN] ―108
[SDI IN]
*1― 109
[ON-SCREEN DISPLAY] ―11 0
[CLOSED CAPTION SETTING] ―11 2
[IMAGE ROTATION] [OFF]11 3
[BACK COLOR] [BLUE]11 3
[STARTUP LOGO] [DEFAULT LOGO]11 3
[UNIFORMITY] ―11 4
[SHUTTER SETTING] ―11 5
[FREEZE] ―11 6
[WAVEFORM MONITOR] [OFF]11 6
[CUT OFF] ―11 8
*1 Only for PT-RZ970
[PROJECTOR SETUP] 
Sub-menu item Factory defaultPage
[PROJECTOR ID] [ALL]11 9
[PROJECTION METHOD] ―11 9
[OPERATION SETTING] ―120
[LIGHT OUTPUT] [100.0%]124
[BRIGHTNESS CONTROL] ―125
[STANDBY MODE] [NORMAL]129
[QUICK STARTUP] [OFF]129
[NO SIGNAL SHUT-OFF] [DISABLE]130
[NO SIGNAL LIGHTS-OUT] [DISABLE]130
[INITIAL STARTUP] [LAST MEMORY]130
[STARTUP INPUT SELECT] [LAST USED]130
[DATE AND TIME] ―131
[SCHEDULE] [OFF]132
[MULTI PROJECTOR SYNC] ―134
[RS-232C] ―135  
						

							Chapter 4 Settings — Menu navigation
80 - ENGLISH
Sub-menu itemFactory defaultPage
[REMOTE2 MODE] [DEFAULT]137
[FUNCTION BUTTON] ―137
[LENS CALIBRATION] [NORMAL]138
[STATUS] ―138
[SAVE ALL USER DATA] ―139
[LOAD ALL USER DATA] ―139
[INITIALIZE] ―140
[SERVICE PASSWORD] ―140
[P IN P] 
Details (x page 141)
[TEST PATTERN] 
Details (x page 143)
[SIGNAL LIST] 
Details (x page 144)
[SECURITY] 
Sub-menu item Factory defaultPage
[SECURITY PASSWORD] [OFF]147
[SECURITY PASSWORD CHANGE] ―147
[DISPLAY SETTING] [OFF]147
[TEXT CHANGE] ―148
[CONTROL DEVICE SETUP] ―148
[CONTROL DEVICE PASSWORD CHANGE] ―149
[NETWORK] 
Sub-menu item Factory defaultPage
[DIGITAL LINK MODE] [AUTO]151
[DIGITAL LINK STATUS] ―151
[NETWORK SETUP] ―152
[NETWORK CONTROL] ―152
[NETWORK STATUS] ―153
[DIGITAL LINK MENU] ―153
[Art-Net SETUP] [OFF]153
[Art-Net CHANNEL SETTING] [2]154
[Art-Net STATUS] ―154
Note
 fSome items may not be adjusted or used for certain signal formats to be input to the projector .
When the items cannot be adjusted or used, the items in the menu screen are shown in black characters, and they cannot be adjusted or 
set.
 f The factory default setting varies depending on the selected input terminal.