Pioneer Rvd Xg10 Projector Specifications

							2.2.5  DSP Command
----------------------------------------------------------------------------------------------------------------
Function: Projector screen display ON/OFF setting.
----------------------------------------------------------------------------------------------------------------
Syntax: DSPY[CR], DSPN[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function:: DISPLAY setting in the ADDITIONAL SET UP menu (when a COMP. or the video input is
selected)
----------------------------------------------------------------------------------------------------------------
 This command is used when the screen display is not needed.
 To set the display ON/OFF through the RS-232C line, use the AKa, EOa or MSa command.
 The current display status can be checked with the GAD command.
    DSPY: Screen display setting
    DSPN: No screen display setting
----------------------------------------------------------------------------------------------------------------
Note: This command is available only in the AJY status with the menu OFF.
After the screen display is set to OFF, other information than the following will not be displayed:
       - Input display when power is turned ON
       - Display of messages related to the lamp
       - Menu screen display
       - Display of messages related to non-compatible signal 
						

							2.2.6  LG Command
----------------------------------------------------------------------------------------------------------------
Function: Display language setting.
----------------------------------------------------------------------------------------------------------------
Syntax: LGE[CR], LGF[CR], LGD[CR], LGS[CR], LGI[CR], LGJ[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function:: LANGUAGE setting in the ADDITIONAL SETUP menu (when a COMP. or the video input is
selected)
----------------------------------------------------------------------------------------------------------------
 This command sets the screen display language.
 The current language status can be checked with the GAD command.
    LGE: English language display
    LGF: French language display
    LGD: German (Deutsch) language display
    LGS: Spanish language display
    LGI: Italian language display
    LGJ: Japanese language display
----------------------------------------------------------------------------------------------------------------
Note: This command is available only in the AJY status with the menu OFF.
      Even when the screen display language is set up using this command, the control commands and return values of
     RS-232C are not affected according to the selected language. 
						

							2.2.7  RP Command
----------------------------------------------------------------------------------------------------------------
Function: Picture vertical/horizontal reversion setting.
----------------------------------------------------------------------------------------------------------------
Syntax: RPN[CR], RPH[CR], RPV[CR], RPF[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function:: REVERSE PICTURE setup in ADDITIONAL SET UP menu (when a COMP. input or the video
input is
                     selected)
----------------------------------------------------------------------------------------------------------------
 This command is used when it is required to hang the system from the ceiling or use it as a rear projection system.
 The picture reversion status can be checked with the GAD command.
    RPN: Normal picture (for use as a front projector)
    RPH: Horizontal, left/right reversion (for use as a rear projector)
    RPV: Vertical, up/down reversion (for use as a ceiling-hung projector)
    RPF: Full, horizontal/vertical reversion (for use as a ceiling-hung projector)
----------------------------------------------------------------------------------------------------------------
Note: This command is available only in the AJY status with the menu OFF. 
						

							2.2.8  BG0/BG1 Commands
----------------------------------------------------------------------------------------------------------------
Function: Background color setting.
----------------------------------------------------------------------------------------------------------------
Syntax: BG0[CR], BG1[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function:: BACKGROUND setup in the ADDITIONAL SET UP menu (when a COMP. input or the video
input is
                     selected)
----------------------------------------------------------------------------------------------------------------
 These commands set the background color to be displayed when there is no input signal or during video muting.
 The background color status can be checked with the GAD command.
    BG0: Black background color
    BG1: Blue background color
----------------------------------------------------------------------------------------------------------------
Note: This command is available only in the AJY status with the menu OFF. 
						

							2.2.9  OT Command
----------------------------------------------------------------------------------------------------------------
Function: COMP. output signal setting.
----------------------------------------------------------------------------------------------------------------
Syntax: OTL[CR], OT1[CR], OT2[CR], OTX[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function:: COMP. OUTPUT setup in the ADDITIONAL SET UP menu (when a COMP. input or the video
input
                     is selected)
---------------------------------------------------------------------------------------------------------------
 This command sets the computer output to be displayed on the external monitor when one is connected to the COMP.
output.
 The computer output status can be checked with the GAD command.
    OTL: Output of the picture being displayed on the projector.
    OT1: Output of the COMP. 1 input.
    OT2: Output of the COMP. 2 input.
    OTX: Output of the picture which is not displayed on the projector.
        (COMP. 2 is output when the COMP. 1 input is displayed.)
        (COMP. 1 is output when the COMP. 2 input is displayed.)
 When the video input is selected, the setup immediately before the video input selection is held.
----------------------------------------------------------------------------------------------------------------
Note: This command is available only in the AJY status with the menu OFF. 
						

							2.2.10 AI Command
----------------------------------------------------------------------------------------------------------------
Function: Audio input setting.
----------------------------------------------------------------------------------------------------------------
Syntax: AIL[CR], AIV[CR], AI1[CR], AI2[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function:: AUDIO INPUT setup in the ADDITIONAL SET UP menu (when a COMP. input or the video
input is
                     selected)
----------------------------------------------------------------------------------------------------------------
 This command sets the audio output from the projector speakers and audio output jacks.
 The audio input status can be checked with the GAD command.
    AIL: Audio switching according to the input selection.
    AIV: Audio of the video input.
    AI1: Audio of the COMP. 1 input.
    AI2: Audio of the COMP. 2 input.
----------------------------------------------------------------------------------------------------------------
Note: This command is available only in the AJY status with the menu OFF. 
						

							2.2.11 SZT/SZE Commands
----------------------------------------------------------------------------------------------------------------
Function: Picture size setting.
----------------------------------------------------------------------------------------------------------------
Syntax: SZT[CR], SZE[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function::
Remote:    [RESIZE]  * Cyclic selection
Main unit: [RESIZE]  * Cyclic selection
----------------------------------------------------------------------------------------------------------------
 These commands set whether a picture with other resolution than 1024*768 is to be displayed in true size or resized
into a full-screen expanded/compressed image.
 1. When the input resolution is below 1024*768 (640*400, 640*400, 800*600, etc.)
    SZT: The picture is displayed in the input resolution so the size is reduced.
    SZE: The picture is expanded to fill the full screen so the size is expanded.
 2. When the input resolution is above 1024*768 (1280*1024, 1152*870, etc.)
    SZT: The picture is displayed in the input resolution so only a part of it is displayed.The reference display
        position is switched in order of top left, bottom left, bottom right, top right and center.
    SZE: The picture is compressed to fill the full screen.
----------------------------------------------------------------------------------------------------------------
Note: These commands are available only in the AJN status when a COMP. input is selected and the menu is OFF.
Digital zooming is canceled.
      This function is not available with input resolution of 1600*1200 or with the HDTV input.
      The initial setting is expanded or compressed display.
      This command can be set independently for the COMP. 1 and COMP. 2 inputs. 
						

							2.2.12 DZ Command
----------------------------------------------------------------------------------------------------------------
Function: Digital zooming setting.
----------------------------------------------------------------------------------------------------------------
Syntax: DZON[CR], DZOF[CR], DZMU[CR], DZMD[CR], DZPU[CR], DZPD[CR], DZPL[CR], DZPR[CR]
----------------------------------------------------------------------------------------------------------------
Equivalent function::
Remote:    Zooming ratio change using [MAGNIFY], [ZOOM W] or [ZOOM T]
Main unit: Zooming ratio change using [MAGNIFY], [ZOOM W] or [ZOOM T]
----------------------------------------------------------------------------------------------------------------
 This command changes the picture size. Compared to the ZUP/ZDW commands (2.3.1), this command magnifies the
picture by means of video signal processing.
    DZON: Digital zooming mode activation command
    DZOF: Digital zooming mode deactivation command
    DZMU: Digital zooming ratio up command
    DZMD: Digital zooming ratio down command
    DZPU: Digital zooming of upper section of picture
    DZPD: Digital zooming of down section of picture
    DZPL: Digital zooming of left section of picture
    DZPR: Digital zooming of right section of picture
----------------------------------------------------------------------------------------------------------------
Note: The DZPU/DZPD/DZPL/DZPR command causes only one step of operation per command.
      Issue the same command repeatedly when sequential operations are required.
DZaa: Available only in the AJN status when a COMP. input is selected and the menu is OFF. 
						

							2.3 Adjustment Commands
       Command NameFunction
2.3.1  ZUP/ZDW Zooming up/down adjustment
2.3.2  FUP/FDW Focusing up/down adjustment
2.3.3  VOL Volume adjustment
2.3.4  FRQ Picture horizontal display range adjustment
2.3.5  PHS Phase (tracking) adjustment
2.3.6  PSU/PSD/PSL/PSR Picture position shifting adjustment
2.3.7  ATS Automatic computer screen setup
2.3.8  CNT Contrast adjustment
2.3.9  BRT Brightness adjustment
2.3.10 COL Color adjustment
2.3.11 TNT Tint adjustment
2.3.12 SHP Sharpness adjustment
2.3.14 CConvergence adjustment 
						

							2.3.1  ZUP/ZDW Commands
----------------------------------------------------------------------------------------------------------------
Function: Picture projection size adjustment.
----------------------------------------------------------------------------------------------------------------
Syntax: ZUP[CR], ZDW[CR]
----------------------------------------------------------------------------------------------------------------
Adjustment range: Undefined (because the motor driving the lens tube is a DC motor, which is not managed in terms
                 of numerical values)
----------------------------------------------------------------------------------------------------------------
Equivalent function::
Remote:    [ZOOM W], [ZOOM T]
Main unit: [ZOOM W], [ZOOM T]
----------------------------------------------------------------------------------------------------------------
 These commands vary the picture projection size according to the screen.
 ZUP increases the projection size and ZDW decreases it.
----------------------------------------------------------------------------------------------------------------
Note: These commands cause only one step of operation per command. Issue the same command repeatedly when
sequential
     operations are required.