Ricoh Mp C4500 Service Manual

							Maintenance
93
6
CPress [Colour Registration].
DPress [OK].
Auto colour registration takes about fifty seconds. When it is completed, the
display returns to the colour registration menu.
EWhen you have made all the settings, press the {User Tools / Counter} key.
The initial display is shown. 
						

							Adding paper, Toner and Staples
94
6
Auto Colour Calibration
If a certain colour is strong or the colour of the copy differs from the original, ad-
just the yellow, magenta, cyan and black balance.
Note
❒If “DAdd Toner” is shown on the display panel, the test pattern cannot be
printed.
APress the {User Tools / Counter} key.
BPress [Maintenance].
AQE901S 
						

							Maintenance
95
6
CPress [Auto Colour Calibration].
DPress [Start].
EPress [Start Printing] and a test pattern will be printed.
FPlace the test pattern on the exposure glass and press [Start Scanning].
The image will be corrected after “
Scanning...Please wait” disappears. 
						

							Adding paper, Toner and Staples
96
6
Note
❒When performing the auto colour calibration from the copy function, press
[Start] under Copier Function. When performing from the printer function,
press [Start] under Printer Function.
❒The test pattern will not be read if it is set in the ADF.
❒When performing the auto colour calibration from the printer function, se-
lect test patterns from [600 × 600 dpi], [1800 × 600 dpi] and [2400 × 600 dpi] and
then press [Start Printing].
❒The test pattern will be printed on an A4K, 8
1/2”× 11”K size page (If
A4K is not available then A3 L, B4 JISL will be used.). Make sure to
check the paper set in the paper tray.
❒Set the test pattern in the following way:
❒When the ADF is installed, make sure to set the test pattern on the expo-
sure glass, and then 2 or 3 white sheets, same size as the test pattern, above
the test pattern.
GCCLCPIE 
						

							Maintenance
97
6
Returning to the Previous Setting
“Previous Setting” means to return to the previous status before any changes.
APress [Previous Setting].
BPress [Yes].
The settings return to the previous contents.
Note
❒When returning the auto colour calibration of the copy function, press [Pre-
vious Setting] of the Copier Function. If returning the auto colour calibration
of the printer function, press [Previous Setting] of the Printer Function.
❒When returning the auto colour calibration from the printer function, se-
lect test patterns from [600 × 600 dpi], [1800 × 600 dpi] and [2400 × 600 dpi] and
then press [Yes]. 
						

							Adding paper, Toner and Staples
98
6Adding Staples
This section explains what to do when staples need replacing.
R CAUTION:
Important
❒Stapling failures or jams may occur if you use a staple cartridge other than
that recommended.
Refill the stapler according to the finisher type. (Check the type if you are un-
sure.) For details about type of finisher, see “Options”, About This Machine.
SR790
The following procedure explains how to add staples to the SR790.
Note
❒If you cannot pull out the upper unit, there are staples remaining inside the
cartridge. Use all the staples, do not add more. Keep your hands clear of the booklet finisher tray when pulling out or push-
ing in the finishers staple unit. You can trap your fingers if you do not.
AQE904S 
						

							Adding Staples
99
6
Finisher SR3030 and Booklet Finisher SR3020
The following procedure explains how to add staples to the Finisher SR3030 and
Booklet Finisher SR3020.
Note
❒If you cannot pull out the upper unit, there are staples remaining inside the
cartridge. Use all the staples, do not add more.
AQE003S 
						

							Adding paper, Toner and Staples
100
6
Booklet Finisher SR3020 (Saddle Stitch)
The following procedure explains how to add staples to the Booklet Finisher
SR3020.
Note
❒If you cannot pull out the upper unit, there are staples remaining inside the
cartridge. Use all the staples, do not add more.
AQE004S 
						

							Replacing the Stamp Cartridge
101
6 Replacing the Stamp Cartridge
If the transmission stamp becomes faint, replace the cartridge.
Important
❒This stamp cartridge is used for facsimile and scanner functions.
❒Do not add ink to the cartridge by yourself. Neglecting this can cause ink
leakage.
❒Be sure not to dirty your fingers with ink from the cartridge.
❒Use the cartridge specified for this machine.
AOpen the ADF cover.
BRaise lever P2, and then pull open cover P2.
CPush on the area of cover P3 marked “PUSH”, and then open the cover P3.
AQD032S
AQD033S
AQD034S 
						

							Adding paper, Toner and Staples
102
6
DPull out the old stamp cartridge.
EInsert the new stamp cartridge.
Push in the cartridge until the metal parts are no longer visible.
FClose cover P3, P2, and the ADF cover.
AQD035S
AQD036S