Samsung Shr5162 N Manual

 
01 INTRODUCING
introducing _07
REMOTE CONTROL
RECORD
Starts or ends the 
recording. 
OPEN/CLOSE
Used to open and close 
the DVD-RW tray.
0~9
Selects a single channel 
while in live mode. Used  for inputting numeric  values. 
REC LOCK
Locks the record function.
AUDIO
Toggles Audio On and 
Off.
BACKUP
Press it for backup 
operation.ALARM
Cancels sending alarms.MODE
Select a split screen.
FR (fast rewind) 
FR (fast reverse): Used for quick backward search while in play. (-x2, -x4,  -x8, -x16, -x32, -x64)...

Figure 1
One Year: 24HR X 365 DAY =8,760 HRTemperature
Unit: ºCLife (Unit: HOURS)
Figure 2
08_ installation
installation
You should pay attention to the following before you use the product.
 Do not use it outdoor.
  Do not place water or liquid near the connection part or the prod
 uct.
  Do not impose excessive shock or force.
  Do not pull out the power cord unreasonably.
  Do not disassemble the product on your own.
  Do not exceed the rated input or output voltage range.
  Use the certified...

 
02 INSTALLATION
installation _09
CAUTION
[Checking HDD Data]Please, pay attention to Following 
information to minimize the 
chance of losing HDD data.
 Remember that you should protect 
HDD from any impact or misuse as 
this may cause damaged.
  The Manufacturer is not responsible 
for missing data or defects caused 
by the user’s mishandling.
Note:  
 Adding Extra HDD. Check 
in advance that the HDD 
is compatible with the 
manufacturer’s DVR.
Examples that can cause loss of data 
or damage HDD. 
...

BRACKET-
HDD(A)
BRACKET-
HDD(B)
BRACKET-HDD(A)
SCREW-SPECIAL
Screwdriver
Screwdriver
10_ installation
3.  There are brackets (Bracket-HDD) mounted 
on the right and left sides where you can 
mount HDDs. Remove the screws holding 
each bracket to mount an HDD onto.
4.  If you want to add a hard disk, remove  Bracket-HDD(A), power supply cable, signal 
transmission cable (IDE Cable), and fan 
cable. 5.  To add a hard disk, the built-in HDD (Primary 
Master) should have been installed. Basically 
a built-in...

BRACKET-HDD(B)
Secondary HDD 
IDE Connector Primary HDD 
IDE Connector
 
02 INSTALLATION
installation _11
6.  To add another hard disk after adding a hard disk completes, remove the Bracket-HDD(B) 
on the DVD-RW driver.
7.  Fix the hard disk to the Bracket using 4  (B)SCREW-MACHINE (6-32UNC, L4. 2) 
provided when purchasing the HDD. The 
screws should be fastened not to come 
loose. Fix the Bracket-HDD(B) using screws 
after aligning 4 spots on the bottom and 
mounting holes. 8.  When adding hard disks...

CONNECTING THE NETWORK
Connecting to Internet through Ethernet (10/100BaseT)
12_ connecting
connecting with other devices
The illustrations are described based on SHR-5162.
CONNECTING VIDEO, AUDIO, AND MONITOR
SHR-5162_Eng.indb   122007-06-18   ｿﾀﾀ・11:47:55 

 
03 CONNECTING
connecting _13
Connecting to Internet through ADSL
CONNECTING THE USB
1.  There are two USB connecting ports on the front and rear panels of the product.
2.  USB Hard Disk, USB CD/DVD, and USB  Memory can be connected through any of 
those ports.
3.  If the USB HDD is connected to the system,  it should be detected and set through 
Menu > System > Storage Setup before 
operation.
4.  The product provides the HOT PLUG feature  that allows the connection/removal of USB 
devices during...

14_ connecting
CONNECTING THE RS-485 
DEVICE
You can connect an RS-485 device through a 
rear port of the product. For example, you can 
connect and control PTZ cameras supporting the 
RS-485 communication. 
You can also adopt either Half Duplex or Full 
Duplex method for exchanging data.
Supportable baud rates are 600, 1200, 2400, 
4800, 9600, 19200, and 38400.
CAUTION
  Check if the RS-485 device is 
compatible with the product first.
  Then pay attention not to change 
the polarity (+/-) of RS-485...

CAM_01
CAM_01 V.Loss
 
04 LIVE
live _15
live
OPERATING THE SYSTEM
Turn on the power and the following Samsung 
logo appears. 
Upon completion of initializing procedure, the 
live screen appears with a beep sound. (It takes 
about one minute until a live screen comes up.) 
 If a new HDD is installed, the initialization 
may take much more time because it 
includes a new HDD initialization.
  If the live screen does not appear or 
the LEDs on the front panel repeat 
f

lickering, please check the...

16_ live
: PTZ icon
T
his icon appears when setting the PTZ device 
and it changes to yellow when operating the PTZ.
: Audio icon
This icon represents the ON/OFF status of audio 
and it changes to yellow when the audio is set to 
ON. It does not appear in Video mode or when 
the audio is disabled.
: Sensor Active icon
This icon appears in the channel linked with the 
external sensor signal when the sensor is active.
: Motion Event icon
This icon appears in the Motion Event channel 
when the motion...