Singer Serger Professional 5 Manual

							 
 
 
 
  
   
  
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                  
 
 
 
 
 
 
 
 
 
 
 
  
 
  3. Thread the top cover thread guide by  pulling the thread towards the left until 
       it slips under the guide.  Then pu ll the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
 
 
  4. While holding the thread firmly,  pull the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
 
  5. Turn the handwheel toward you unt il the lower looper extends 5-10mm  
                (approximately ½ inch) fr om the needle plate edge.  
 
 
 
 
  6. Thread the looper area of the ma chine following the green color coded  
       thread guides 4-9. 
 
  
   
 Four-Thread Ultra-Stretch Mock Safety Stitch page 8  
						

							 
   
   
   
 
 
 
  
 7. Thread the hole in the Upper  Looper from front to back k.  Pull about 4  
                 inches of thread through the loope r and place to the back of the  
                 throat plate. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

						

							 
   
  
 
  
  3. Thread the top cover thread guide by pu lling the thread towards the left until    
                it slips under the guide.  Then pull the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
  4. While holding the thread, firmly  pull the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
   
  5. Turn the handwheel toward you unt il the lower looper extends 5-10mm  
       (approximately ½ inch ) from the needle plate edge.  
 
  6. Thread the looper area of the mach ine following the red color coded  
       thread guides 4-10.  
 
  
  7. Place the thread slighty from left and  
      to the ri ght of threading guide  f. 
 
 
 
  
 
  8. Place the thread slightly from the  
               fr ont and to the back of threading 
               guide  g. 
 
 
 
 
    9. Place the thread through  h, i ,and  j. 
  
Four-Thread Ultra-Stretch Mock Safety Stitch page 10  
						

							 
 10. Thread the looper eye (A)  from front to back.  Pull about 4 inches of thread. 
                 Position thread into V cutout (B) on thr eader.  Firmly hold thread tail with left   
                  hand and pull Threader lever (C) up into place (D).  
 
 
   
 
 
 
 
 
 
 
 
 
 
   
 
   
 
 
 
 
 

						

							 
   
  
  3. Thread the top cover thread guide by pulling the thread towards the left until 
       it slips under the guide.  Then pu ll the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
 
 
 
  4. Continue to thread point s 4-8.  Slip the thread into the rear slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the right  slot of the thread guides i and  j.  
 
  
 
 
 
 
 
 
 
 
 
 
 
   
  5. Before threading the eye of the needl e, make sure the thread is behind
   
               the thread guide located on the  bottom of the needle clamp. 
 
  6. Thread the eye of the Overedge Right Needle  k. 
 
  
 
 
 
 
 
 
 
 
 
   6 
Four-Thread Ultra-Stretch Mock Safety Stitch page 12  
						

							 
   
  
 
  5. Continue to thread point s 4-8.  Slip the thread into the middle slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the middle  slot of the thread guides i and  j.  
 
  6. Before threading the eye of the needl e, make sure the thread is behind
  
               the thread guide located on the  bottom of the needle clamp. 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
 
 
 
  7. Thread the eye of the Left Overedge Needle  k. 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
  
  8. Draw about 4 inches of the thr ead through the needle eye towards the back 
      of the machine.  
  
      9. Place the thread  to the back, under the Presse r Foot.  Lower foot and sew. 
 
Four-Thread Ultra-Stretch Mock Safety Stitch page 14  
						

							 
   
   
   
   
  
  
                   
 
                                   
Chapter 8:         
        Four-Thread Safety Stitch