Singer Serger Professional 5 Manual

							 
   
  
 
4. Turn the hand wheel toward you until  the Chainstitch Looper extends out   
                10mm  (approximately ½ inch ) from the needle plate edge. 
 
  
 
 
 
 
 
 
 
 
 
  5. Thread the looper area of the ma chine following the brown color-coded  
               thread guides 4-11.  Us e the tweezers provided in the accessory case to  
               aid in threading the looper. 
 
  6. Place the thread through threading guides  f and  g. 
 
 
           7. Continue threading    
               guides  h, i , j and  k. 
 
 
 
  
 
 
 
  8. Thread the looper eye (A) from front to  back.  Pull about 4 inches of thread  
                through the looper.  Position the thread into  the V cutout (B) on the threader.   
               Firmly hold the thread tail with your  left hand and pull threader lever (C) up   
                into place (D).  Gently pull 5-6”  of thread to the back of the machine. 
 
 
  
 Triple Cover Hem page 7 
“V” cutout 
Threader Lever  
						

							 
   
   
   
   
  
 
  5. Continue to thread point s 4-8.  Slip the thread into the rear slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the right  slot of the thread guides i and  j.  
 
  6. Before threading the eye of the needle,  make sure the thread is in front
 of  
               the thread guide located on the  bottom of the needle clamp. 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
 
 
 
  7. Thread the eye of the Ri ght Cover Stitch Needle k. 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
  
  8. Draw about 4 inches of the thr ead through the needle eye towards the back 
      of the machine.  
  
      9. Place the thread  to the back, under the Presse r Foot.  Lower foot and sew. 
 
                      Triple Cover Hem page 9   
						

							 
   
  
  5. Continue to thread points 4-8.  Slip the thread into the middle slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the middle  slot of the thread guides i and  j.  
 
  6. Before threading the eye of the needle,  make sure the thread is in front
 of  
               the thread guide located on the bottom  of the needle clamp for the Cover  
                Stitch or Chainstitch. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
  7. Thread the eye of the middle needle  k. 
 
  
 
 
 
 
 
 
 
 
 
 
  
 
 
  8. Draw about 4 inches of the thr ead through the needle eye towards the back 
      of the machine.  
  
      9. Place the thread to  the back, under the Presser F oot.  Lower foot and sew.   
 
 4 
   5 
7 
 8 
   6 
  Triple Cover Hem page 11   
						

							 
   
   
   
  
 
  5. Continue to thread point s 4-8.  Slip the thread into the forward slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the left sl ot of the thread guides i and j .  
 
  6. Before threading the eye of the needle,  make sure the thread is in front
 of  
               the thread guide located on the  bottom of the needle clamp. 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
 
 
 
  7. Thread the eye of the Left Cover Stitch Needle  k. 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
  
  8. Draw about 4 inches of the thr ead through the needle eye towards the back 
      of the machine.  
  
      9. Place the thread  to the back, under the Presse r Foot.  Lower foot and sew. 
 
                             Triple Cover Hem page 13