Tone Commander 30e120 Installation Instructions

Using Configuration Programming Mode
The configuration programming mode must be entered prior to attempting any of the following
programming procedures.Enter this mode only when the console is idle, i.e., no calls are in progress or on
hold and the time of day is displayed.
The Configuration Program Lock Switch (switch #2) inside the 30e CPU must beOFF(unlocked) before
proceeding (see pages 15 and 36).
Toenterconfiguration programming mode:

Press HOLD.

Press TRANSFER.

Press RELEASE.

Press dial pad...

Page 4213-102499 Rev. G
Tone Commander 30e120 Installation Instructions
Figure 17– 30e Console Keys 

13-102499 Rev. GPage 43
Tone Commander 30e120 Installation Instructions
Figure 18– 120 Console (#1) Keys 

Page 4413-102499 Rev. G
Tone Commander 30e120 Installation Instructions
Figure 19– 120 Console (#2) Keys 

Programming System-Wide Features
Timing Parameters and Night Service Mode

Press HOLD, then TRANSFER, then RELEASE, thenC(2) on the dial pad to enter configuration
programming mode.
CONFIGURE PROG will be displayed.

Press a line key to select the feature to be programmed.
The display will show the item name and the current value.
The station status lamp will light steadily.

Press a key on the dial pad if you want to change the value.
The new value will be shown in the display. Changes are stored...

Timing values listed in the following tables are nominal, and may differ slightly from the actual values.
Shaded values are factory defaults.
Abandoned Ring Time
Dial Pad Key Available Values
2 2 sec
3 3 sec
4 4 sec
5 5 sec
6 6 sec
7 7 sec
8 8 sec
9 9 sec
0 10 sec
Table 15
Recall Rings
(with 120 console only)
Dial Pad Key Available Values
1 1 ring
2 2 rings
3 3 rings
4 4 rings
5 5 rings
6 6 rings
7 7 rings
8 8 rings
9 9 rings
0 no recall
Table 16
Page 4613-102499 Rev. G
Tone Commander 30e120 Installation...

Pickup Code Sequence
(with 120 console only)
Dial Pad Key Available Values
0first
(before station #)
1last
(after station #)
Table 17
Dialing Speed
Dial Pad Key Available Values
6slow
(6 digits/sec)
0fast
(10 digits/sec)
Table 18
Pause Time
(with 120 console only)
Dial Pad Key Available Values
2 200 ms
3 300 ms
4 400 ms
5 500 ms
6 600 ms
7 700 ms
8 800 ms
9 900 ms
Table 19
13-102499 Rev. GPage 47
Tone Commander 30e120 Installation Instructions
Line key to select feature:C
Default value:first
This...

Hookflash Time
Dial Pad Key Available Values
5 500 ms
6 600 ms
7 700 ms
8 800 ms
9 900 ms
0 1 sec
Table 20
Dial Tone Detect Time
(with 120 console only)
Dial Pad Key Available Values
1 500 ms
2 600 ms
3 700 ms
4 1 sec
5 1.2 sec
6 1.5 sec
7 1.8 sec
8 2 sec
Table 21
Page 4813-102499 Rev. G
Tone Commander 30e120 Installation Instructions
Line key to select feature:F
Default value:600 ms
This parameter sets the length of a timed hookflash generated
during call transfer and autodial operations. The default...

Hold Recall Time
Dial Pad Key Available Values
3 30 sec
4 40 sec
5 50 sec
6 60 sec
9 90 sec
1 2 min
2 3 min
0 no recall
Table 22
Hold Release Time
Dial Pad Key Available Values
140ms
280ms
3 200 ms
4 400 ms
5 600 ms
6 800 ms
7 1 sec
8 2 sec
Table 23
13-102499 Rev. GPage 49
Tone Commander 30e120 Installation Instructions
Line key to select feature:H
Default value:90 sec
Calls on console hold or camp-on longer than the Hold Recall
Time will recall the console.
Set this parameter according to customer...

Park Recall Time
(with 120 console only)
Dial Pad Key Available Values
3 30 sec
4 40 sec
5 50 sec
6 60 sec
9 90 sec
1 2 min
2 3 min
Table 24
Night Bell Mode
Dial Pad Key Available Values
1 lines only
2 lines + stations
Table 25
Page 5013-102499 Rev. G
Tone Commander 30e120 Installation Instructions
Line key to select feature:J
Default value:90 sec
Parked calls that are not retrieved before the time specified in
this parameter will recall the console.
Set this parameter according to customer preference....