Toshiba Bev4t User Manual

1. PRODUCT OVERVIEW ENGLISH VERSION EO1-33035 1.5 Appearance 
 
E1- 5 
1.5.5  Button and Indicator  Lamp The [FEED] button operates as FEED button or PAUSE button 
depending on the printer statuses.  
As the FEED button  • 
Pressing this button when the printer is in online 
state causes a media feed.  
•  Pressing this button after removing a cause of 
an error returns the printer to online state.  
As the PAUSE 
button  • 
Pressing this button during printing stops 
printing after completing the...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.1 Precautions 
 
E2- 1 
2. PRINTER SETUP 
 
 
 
 
 
2.1 Precautions 
 
 
 
 
 
 
 
 
 
   
 
This section outlines the steps necessary to
 setup your printer prior to its 
operation.  The section includes precautions, connecting cables, 
assembling accessories, loading media and ribbon, and performing a test 
print. 
 
 
To insure the best operating environment, and to assure the safety of the 
operator and the equipment, please observe the following...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.2 Procedure before Operation
 
E2- 2 
2.2  Procedure before   Operation  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.3  Turning the Printer  
 ON/OFF  
 
2.3.1  Turning ON the Printer  
 
 
 
 
 
 
This section describes the outline of the printer setup. 
1.  Unpack the accessories and printer from the box. 
2.   Refer to Safety Precautions in this manual and set up the printer at a 
proper location. 
3.   Make sure that the Power Switch is off. (Refer to  Section 2.3.)...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 
2.4 Connecting the Cables to the Printer
 
E2- 3 
2.3.2  Turning OFF the   Printer
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  1.
  Before turning off the printer power switch verify that the Indicator  
  Lamp is illuminated in green, not flashing. 
2.  To turn OFF the printer power press the power switch as shown in the 
diagram below.  Note that (  { ) is the power OFF side of the switch. 
   
 
 
 
 
 
 
   
CAUTION! 
1.  Do not turn off the printer  power while the...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 
2.4 Connecting the Cables to the Printer
 
E2- 4 
2.4 Connecting the  Cables to the Printer
 
 
  The following paragraphs outline how
 to connect the cables from the 
printer to your host computer, and  will also show how to make cable 
connections to other devices.  Depe nding on the application software you 
use to print labels, there are four possibilities for connecting the printer to 
your host computer.  These are: 
•  A serial cable connection between...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 
2.5 Connecting the Power Adapter and the Power Cord
 
E2- 5 
2.5 Connecting the  Power Adapter and 
the Power Cord
 
 
 
 
 
 
 
 
  1.
 Make sure that the printer power  switch is in the OFF (O) position. 
2 .  Insert the Power Cord into th e inlet of the Power Adapter. 
 
 
 
 
3.   Insert the Power Adapter connector  into the Power Jack on the rear of 
the printer.  
 
 
 
 
Power Adapter  
Power Cord
Power Adapte
r
Connector
Power Jack 
NOTES: 
1.  Since...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 
2.6 Opening/Closing the Top Cover
 
E2- 6 
2.6 Opening/Closing the  Top Cover
 
 
  When opening or closing the Top Cover, please be sure to follow the 
instructions below. 
 
To open the Top Cover:  
 
1.
  Press down the Top Cover Release Button to unlock the Top Cover, 
then fully open the Top Cover.  
 
 
 
 
As the Top Cover is held by the damper, it does not close under its own 
weight. 
 
 
 
 
To close the Top Cover:  
 
1.   Press down the portions of...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media
 
E2- 7 
2.7  Loading the Media  
 
 
 
 
 
 
 
 
 This section describes how to load a me dia in the printer.  This printer 
accepts label rolls, tag rolls, and  fanfold paper stocks.  Please use 
TOSHIBA TEC approved media.   
 
NOTES:  1.  Please perform a media sensor calib ration whenever you change the 
media type.  
  2.  The size of the media which can be  loaded inside the printer is as 
follows:   
Outer roll diameter: Max. 127mm...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media
 
E2- 8 
2.7  Loading the Media  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  2.
  Slide the Media Holder Lo ck Switch to the Unlock (▲) side to  
  release the Media Holders. 
 
 
 
3.   Open the Media Holders.  
 
 
 
4.   Place a media roll between the Media  Holders so that the media is fed 
with the print side facing up.  Fit the projection of the Media Holders \
into the core.  Make sure...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media
 
E2- 9 
2.7  Loading the Media  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  6.
  Adjust the media sensor position and  select a sensor type to be used.  
(Refer to Section 2.9.1)
 
 
This printer is provided with a Black  Mark Sensor which detects black 
marks printed on the reverse side of the media, and a Feed Gap Sensor 
which detects inter-label gaps.  
As the Feed Gap Sensor position is fixed, it is not...