Toshiba Bev4t User Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media
 
E2-10 
2.7  Loading the Media  (Cont.)


 
 
 
  9.
  Close the Top Cover gently and push down the arrow-indicating  
  portions until they click.  


 
 
 
10.   Press the [FEED] button to check for a proper media feed.  










 
 
There are three issue modes ava ilable for this printer.   
 
Batch mode:
 
In the batch mode, the media is c ontinuously printed and fed until the 
number of media specified in the issue command has been...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media
 
E2-11 
NOTES : 
1.  When issuing labels without  removing them from the backing 
paper, it is not necessary to pass 
the media through the Strip Block.  
2.  When the media is correctly set,  the backing paper is supposed to 
be pinched by the Platen and the 
Strip Feed Roller as shown below. 
 
 
 
 
 
 
 
 
 
 
 
3.  If the peel-off issue is performed  under intense light, the strip sensor 
may not correctly detect the 
presence of a...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media
 
E2-12 
2.7  Loading the Media  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  Cut mode (Option):
 
When the Cutter is installed, the media is automatically cut.  
After loading the media as described  on the previous pages, insert the 
leading edge of the media through the Media Outlet of the Cutter Cover. 
 
 
 
 
 
 
 
 
 
 
How to Load Fanfold Paper Stock 
1.   Place the fanfold paper stock on the...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.7 Loading the Media
 
E2-13 
2.7  Loading the Media  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  When a media roll has an outside diameter exceeding 127 mm (5
”) and 
the inner core diameter of 76.2 mm (3 ”), the optional External Media Roll 
Hanger is required. 
 
1.   Fit the protrusions on the bottom of the printer into the holes in the 
External Media Roll Hanger.  
   
2.   Insert the Media Shaft into the...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.8 Loading the Ribbon
 
E2-14 
2.8  Loading the Ribbon 
 
 
 
 
 When you use normal media, it is necessary to load a ribbon. 
Follow the procedure below to load a ribbon properly.  
 
1.   Press down the Top Cover Release Button to unlock the Top Cover, 
then fully open the Top Cover. 
 
 
 
 
2.  Fit the core of the Ribbon Supply Roll into both the Spring Guide 
Wheel and the Guide Wheel (Supply side).  
 
  (1) Push the right side of the core of the Ribbon...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.8 Loading the Ribbon
 
E2-15 
2.8  Loading the Ribbon 
 (Cont.)
 
 
3.  Push up the Ribbon Access Cover by the portions indicated by  
  arrows A and fully open it supporting the Print Head Block.
  
 
 
 
4.   Fit the Ribbon Take-up Roll to the Spring Guide Wheel and the Guide 
Wheel in the same way as the Ribbon Supply Roll.   
 
  (1) Push the right side of the core of the Ribbon Take-up Roll against the  Spring Guide Wheel and fit th e wheel into the...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 2.8 Loading the Ribbon
 
E2-16 
2.8  Loading the Ribbon 
 (Cont.)
 
 
6.  Close the Ribbon Access Cover until it clicks.  
 
 
 
7.   Again, turn the Ribbon Rewind Gear to remove any slack of the 
ribbon. 
 
 
 
8.  Close the Top Cover gently and push down the front part of the Top 
Cover until they click.  
 
 
 
 
Now, the ribbon loading is completed.  
 
 
Ribbon Access 
Cover 
Print Head 
Block 
Ribbon  
Rewind Gear 

2. PRINTER SETUP ENGLISH VERSION EO1-33087 
2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities
 
E2-17 
2.9 Media Sensor  Calibration, Self Print 
Test, and Dump Mode 
Utilities 
 
2.9.1 Media Sensor  Calibration 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
This utility is used to calibrate th e sensitivity of the Feed Gap/Black 
Mark Sensor.  
It is necessary to set the media senso rs after the media is changed to 
different type .  
 
 
 
 
1....

2. PRINTER SETUP ENGLISH VERSION EO1-33087 
2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities
 
E2-18 
2.9.2  Self Print Test and  Dump Mode 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.   Turn off the printer power and install a media roll on the printer.  
2.
 Press the [FEED] Button while turning on the printer.  The Indicator 
Lamp will light up in the following order: 
Green (Flashing)   →  Red (Flashing)   →  Orange (Flashing)   →     
Orange   →  RED   →  Green...

2. PRINTER SETUP ENGLISH VERSION EO1-33087 
2.9 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities
 
E2-19 
2.9.2  Self Print Test and  Dump Mode (Cont.) 
 
 
 
  The test print contents should be changed by the following commands 
and parameters: 
 PROGRAM VERSION: VX.XX  XXXX --- Fi
rmware version and checksum 
TONE ADJUST: +XX ------------------------- Print tone fine adjustment value 
FEED ADJUST: +XX.Xmm ------------------ Print position fine adjustment value 
CUT POSITION ADJUST:...