Toshiba Bsa4tp User Manual

2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media
 
E2- 8 
2.3  Loading the Media  (Cont.)  
 
 
 
  12.
 There are three issue modes available  on this printer.  How to set the  
  media for each mode is provided below.  
 
  
In the batch mode, the media is c ontinuously printed and fed until the 
number of labels/tags specified in the issue command have been printed.  
(1)  Pull the top edge of the media past the Platen.  
 
 
(2)  Close the Top Cover until it clicks.  
 
 
 
 
When...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media
 
E2- 9 
2.3  Loading the Media  (Cont.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  (2)  Press down the Release Bar to open the Strip Unit.  
 
  
 
 
(3)  Remove enough labels from the leading edge of the media to leave 
  300mm of backing paper free.  
(4)  Pass the backing paper through the opening under the Backing Paper 
Feed Roller.  Then, close the Strip Unit until it clicks.  
 
 
  
 
 
(5)  Insert the...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.3 Loading the Media
 
E2-10 
2.3  Loading the Media  (Cont.)  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 
When the optional Cutter Module is fitted, the media is automatically cut.   
 
Insert the leading edge of the media 
into the Media Outlet of the Cutter 
Module. 
 
 
 
 
 
 
13.   Change the print head pressure  according to the thickness of the 
  media to be used, by using the Head Position Lever.  
 
 
 
  Media type or thickness  Head Position 
Lever...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.4 Loading the Ribbon
 
 
 
E2-11 
2.4  Loading the Ribbon 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  There are two types of media available for printing on: these are thermal 
transfer media (normal media) and direct thermal media (with a 
chemically treated surface).  DO NOT LOAD a ribbon when using a 
direct thermal media. 
 
1.
  Press the Top Cover Release Button and gently open the Top Cover to 
its fully open position supporting...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.4 Loading the Ribbon
 
E2-12 
2.4  Loading the Ribbon  (Cont.) 
 
 
  3.
  Lower the Top Cover to its 45
° angle open position.  While pushing  
  the Top Cover Stopper, raise the Top Cover again.  This will fix the  Top Cover.  
 
 
4.   Open the Ribbon Cover.  
 
 
5.   Fit the ribbon take-up core into the Ribbon Holder (Take-up side), 
aligning the notch of the ribbon core with the protrusion of the Ribbon \
Stopper. 
 
 
 
6.  Turn  the ribbon take-up...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.4 Loading the Ribbon
 
E2-13 
2.4  Loading the Ribbon  (Cont.) 
 
 
 
 7.  Close the Ribbon Cover until it clicks.   
 
 
8.   Gently close the Top Cover until it clicks.
  
 
 
Be sure to close the Ribbon 
Cover before closing the Top 
Cover.  It is dangerous to close
the Top Cover with the Ribbon 
Cover opened, as the Ribbon 
Cover slams shut. 
WARNING! 
Ribbon Cover
Top Cover  

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.5 Connecting the Printer to Your Host Computer
 
E2-14 
2.5 Connecting the  Printer to Your Host 
Computer  
  The following paragraphs outline how to connect your host computer to 
the printer, and will also show how 
to make cable connections to other 
devices.  Depending on the system configuration you use to print labels, 
there are 5 possibilities for connecting the printer to your host computer.  
These are: 
•  A parallel cable connection between  the...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 2.6 Turning the Printer ON
 
E2-15 
2.6 Turning the Printer  ON
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  When the printer is connected to your host computer it is good practice to 
turn the printer ON before turning on your host computer and turn OFF 
your host computer before turning off the printer. 
 
 
1.
  To turn ON the printer power, press the Power Switch as shown in the 
diagram below.  Note that (  | )
 is the power...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-16 
2.7  Setting an Operating  Environment 
 
 
 
 
 
 
 
 
  Depending on the settings of your host computer or an interface to be 
used, it may be necessary to change the printer parameter settings. 
 
Follow the procedures described below 
to change the printer parameter 
settings in the System Mode to correspond to your environment.  
 
 
 
 
 
 
 
 
 
 
The System Mode consists of the following menus.  
 
 
RESET...

2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.7 Setting an Operating Environment
 
E2-17 
2.7.1  How to Enter the  System Mode  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2.7.2 Parameter Setting 
 
 
 
  This section describes how to enter the System Mode. 
 
 
1.
  Turn on the printer and confirm that “ONLINE” appears on the LCD 
Message Display. 
 
 
 
 
 
 
 
2.  Press the  [PAUSE] key to pause the printer. 
 
 
 
 
 
 
 
 
 
 
 
 
 
3.   Hold down the  [RESTART] key for three...