Toshiba Bsa4tp User Manual

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-38 
(8)  Select “Search for the best driver for your device. (Recommended)”. 
  Mark the “Specify a location” checkbox, then click on the  [Browse] button. 
 Specify “ \driver\WinMe-9x ” folder, then click on the  [Next] button. 
 
 
 
(9)  Check to see that the “ TEC B-SA4T” driver is detected, then click on the  [Next] button. 
  
  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-39 
(10) Change the printer name if necessary, and select  whether or not you use the printer as the default 
printer (“Yes” or “No”).  Click on the  [Finish] button. 
  
 
(11) When the screen, which indicates TEC B-SA4T h as been installed, is displayed, click on the 
[Finish]  button. 
  
 
(12) When installation is completed, the new  printer icon is added in the “Printers” folder.  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-40 
 
   
 
(1)  Log on to your host computer as a member who has full control access privilege concerning the printer settings. 
(2)  Turn the printer ON, then connect it to  your host computer with the USB cable. 
(3)  “USB Device” is automatically detected, and “U SB Printing Support” is automatically installed. 
(4)  After a while, for Windows XP, “ TEC B-SA4T” is detected as a new device.   
  For Windows 2000, “Unknown” device is detected as a new device.  In both cases, perform the  following steps, though dialog boxes for Windows XP are used.  
(5)  The “Add New Hardware Wizard” dialog box is displayed.    Select “Install from a list or specific location (Advanced)”, then click on the  [Next] button. 
  
 
Windows 2000/XP
NOTE : 
When plug-and-play printer installation in progress is stopped, be sure \
to delete the printer detected an
d
displayed on the “Device Manager” tab of the “System Properties\
” dialog box.   
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-41 
(6)  Select “Search for the best  driver in these locations”. 
  Mark the “Include this location in  the search” checkbox, then click on the  [Browse] button. 
  Specify the “ \driver\WinXP-2000 ” folder in the CD-ROM, then click on the  [Next] button. 
  
 
(7)  When the dialog box below is displayed, click on the  [Continue Anyway] button. 
   
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-42 
(8)  When the “Completing the Found New Hardware  Wizard” screen is displayed, click on the 
[Finish]  button.   
 
 
(9)  When installation is completed, the new pr inter icon is added in the “Printers” folder.  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-43 
2.8.4.  Uninstalling the Printer Driver 
 
 
 
 
 
   (1)  Select “Settings” – “Printers” from the  “Start” menu to open the printer folder. 
(2)  Right-click on the printer driver icon to be delete d, then select “Delete”.  The confirmation message is 
displayed. 
(3)  Click on the  [Yes] button to delete.   
(4)  After the printer driver icon is deleted, restart your host computer. 
 
  
(1)  Log on to your host computer as a member who has full control access privilege concerning the printer settings. 
(2)  Select “Settings” – “Printers” from the  “Start” menu to open the printer folder. 
(3)  Right-click on the printer driver icon to be delete d, then select “Delete”.  The confirmation message is 
displayed. 
(4)  Click on the  [Yes] button to delete.   
(5)  After the printer driver icon is deleted, restart your host computer. 
 
   (1)  Log on to your host computer as a member who has full control access privilege concerning the printer settings. 
(2)  Select “Settings” – “Printers” from the  “Start” menu to open the printer folder. 
(3)  Right-click on the printer driver icon to be delete d, then select “Delete”.  The confirmation message is 
displayed. 
(4)  Click on the  [Yes] button to delete.   
(5)  After the printer icon is deleted, select “Serve r Properties” from “File” menu of the “Printers” folder. 
(6)  Select the printer driver to be deleted, then click on the  [Remove] button.   After the printer driver is 
deleted, restart your host computer. 
NOTE:  
Before uninstalling the printer driver, be sure to complete  all of printing, the status monitor, and properties settings.  
Windows 95/98/ME
Windows NT4.0 
Windows  2000/XP 
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-44 
2.8.5  Adding/Deleting a LAN Port 
To use the LAN interface, first, you have to make the following settings in “  IP ADDRESS” in the system 
mode of the printer. (Refer to  Section 2.7.3) 
•  Set the printer IP address (“ PRINTER IP ADRES”), the gateway IP address (“ GATEWAY IP 
ADRES ”), and subnet mask (“ SUBNET MASK”). 
•  Set the port number (“ SOCKET PORT”). 
 
Among these settings, the printer IP address and the por t number are also required for adding a LAN port. 
 
(1)  Adding a LAN Port 
 
 
(1)  Right-click on the printer icon.  Select “Prope rties” to open the printer “Properties” dialog box. 
(2)  Select the “Details” tab, and click on the  [Add Port…] button.  The “Add Port” dialog box is 
displayed. 
(3)  Select “Other”.   
  Select “Seagull Scientific TCP/IP Port” from the list, then click on the  [OK] button. 
(4)  On the “Add Seagull TCP/IP Port” dialog box, enter the name or IP address, the port number, and the  port name.  For the IP address and the port number, enter the same ones as you have set in “  IP 
ADDRESS ” in the system mode of the printer.  After entering these, click on the  [OK] button. 
  
(5)  When addition of the port is completed, the por t is added to the drop down list for “Print to the 
following port”. 
Windows 95/98/ME 
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-45 
 
(1)  Right-click on the printer icon.  Select “Prope rties” to open the printer “Properties” dialog box. 
(2)  Select the “Ports” tab, and click on the  [Add Port…] button.  The “Printer Ports” dialog box is 
displayed. 
(3)  Select “Seagull Scientific TCP/IP Port” from th e “Available Printer Ports” list, then click on the [OK] 
button. 
(4)  On the “Add Seagull TCP/IP Port” dialog box, enter the name or IP address, the port number, and the  port name.  For the IP address and the port number, enter the same ones as you have set in “  IP 
ADDRESS ” in the system mode of the printer. (Refer to  Section 2.7.3)  After entering these, click on 
the  [OK]  button. 
(5)  When addition of the port is completed, the port is  added to the “Print to the following port(s)” list. 
 
(2)  Deleting a LAN Port 
 
 
 
 
 
 
(1)  Right-click on the printer icon.  Select “Prope rties” to open the printer “Properties” dialog box. 
(2)  Select the “Details” tab, and click on the  [Delete Port…] button. 
(3)  Select the port to be deleted, then click on the  [OK] button. 
(4)  When deletion of the port is completed, the port is  also deleted from the “Print to the following port” 
list. 
 
 
(1)  Right-click on the printer icon.  Select “Prope rties” to open the printer “Properties” dialog box. 
(2)  On the “Ports” tab, select the port to be deleted, then click on t\
he  [Delete Port] button. 
(3)  When deletion of the port is completed, the por t is also deleted from the “Print to the following 
port(s)” list. 
 
Windows NT4.0/2000/XP 
Windows 95/98/ME
Windows NT4.0/2000/XP 
NOTE: 
Before deleting a port, be sure to check if other printers al so use it.  If there are printers which use the port to
be deleted, change their port to another, before deleting the port.  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-46 
2.8.6 Cautions 
(1)  Printer Driver Upgrades  
•   To upgrade the printer driver to this version, uninsta ll the previous version of the printer driver, before 
installing this printer driver. 
•   Be sure to restart your host computer, after you upgrade the printer driver. 
•   When your operating system is Windows 95, Windows  98, or Windows Me, be sure to restart your host 
computer, after you uninstall the previous version of  the printer driver.  Or, the printer driver is not 
upgraded properly. 
 
(2)  Others  
•   If your operating system is Windows 2000 or Windows  XP, when plug-and-play printer installation in 
progress is stopped, be sure to delete the printer de tected and displayed on the “Device Manager” tab of 
the “System Properties” dialog box. 
•   Before uninstalling the printer driver, be sure to  complete all of printing, the status monitor, and 
properties settings. 
•   Before deleting a port, be sure to check if other prin ters also use it.  If there are printers which use the 
port to be deleted, change their port  to another, before deleting the port. 
  
						

							
2. PRINTER SETUP ENGLISH VERSION EO1-33048 
2.8 Installing the Printer Drivers
 
E2-47 
2.8.7  Using the Printer Driver  
For how to use the Printer Driver, please refer  to the Help for Windows Printer Drivers screen. 
 
1)  Open the Properties screen of the Printer Driver.  
2)  Clicking on the  About tab causes the following screen to appear. 
  Click on the  [Help] button. 
 
3)  The Help for Windows Printer Drivers screen appears.   This screen will provide how to use the printer 
driver.  
 
About  tab 
[Help]  button