Xerox WorkCentre 7345 User Manual

29
TCP/IP LPD Enablement 
To support TCP/IP printing through the workstations LPR port in the case of Windows XP, the LPD (Line 
Printer Daemon) MUST be enabled at the device.
To view or change the Devices LPD setting, perform the following steps:
To access LPD Settings at the Device
1. Press the rectangular Log In / Out button on the Control Panel.
2. Press the 1 key on the numeric keypad five consecutive times.  (This is the factory default 
password.)
3. Press Enter on the touch screen.
4. Press the...

30
Port Status (LPD Enablement)
1. On the LPD selections menu, press the selection line labeled Port Status.
2. Press the Change Settings button.
3. On the LPD Port Status screen, note which of the two buttons is highlighted as the current setting for 
LPD Enablement.  The available settings are Enabled or Disabled.  For the LPD to function, it must be 
set to Enabled.
4. To change settings, press your setting of choice, then press the Save button.
5. To exit the screen, without making any changes, press...

31
TCP/IP Dynamic Addressing 
1. Open your Web browser and enter the TCP/IP address of the Device in the Address or Location field.  
Press Enter.
2. Click the Properties Tab.
3. Click the plus symbol (+) to the left of the Connectivity, then the Protocols file folder.
4. Select TCP/IP in the directory tree
5. Review the available selections as displayed on your screen and explained in the TCP/IP 
Configuration Selection List, below.`
6. Accept the default Host Name, or type in your own unique Host Name...

32 TCP/IP Configuration Selection List
As displayed on your screen, the following selections are available for TCP/IP Configuration.
IP Mode
Select the IP Mode that applies to your network environment.
General
Host Name.  The default entry assures a name that is unique to this device on the network.
IP Address Resolution.  Use this drop-down menu to select the method to use to assign IP 
Addresses.  Select STATIC, DHCP, RARP, BOOTP, or DHCP/Autonet.
Note that with the Autonet option selected, if a...

33
IP Filtering (IP Address Restriction)
1. Open your Web browser and enter the TCP/IP address of the Device in the Address or Location field.  
Press Enter.
2. Click the Properties Tab.
3. Click the plus symbol (+) to the left of the Security file folder.
4. Select IP Filtering.
5. In either the IPv4 area or the IPv6 area, complete the following steps.
Note: IPv4 is the traditional (xxx.xxx.xxx.xxx) address space used with TCP/IP networks.
a. To allow universal, unrestricted access to the device, clear...

34
Configure Port 9100 (Raw Printing) 
1. Open your Web browser and enter the TCP/IP address of the Device in the Address or Location field.  
Press Enter.
2. Click the Properties tab.
3. Click the plus (+) symbol to the left of the Connectivity, then the Protocols file folder.
4. Select Port 9100 in the directory tree.  (1)
5. The available selections include:
TCP Port Number, with a default value of 9100.  This value typically does not need to be changed.
A TBCP Filter checkbox (displayed when...

35
Microsoft (NetBIOS over IP) Networks 
Before You Start
1. Print a Configuration Report as stated in the Network Connectivity section of this guide.
2. Referring to the report, verify that SMB is enabled.  To enable SMB at the Device, if required, follow 
the procedure below.
3. Referring to the Configuration Report, verify that DNS is enabled.  The use of Naming Servers is 
REQUIRED to resolve NetBIOS device names to IP addresses for packet routing over the TCP/IP 
network.
4. To enable the Device to...

36 7. Press Port Settings.
8. When the Port Settings menu displays, press the SMB selection line.
9. Press the Change Settings button in the lower right corner of the Port Settings menu screen.
10. When the SMB selection menu displays, note that you have only one setting available on a single, 
numbered horizontal line.  Press this selection line.
11. Press the Change Settings button.
12. On the SMB Port Status screen, note which of the two buttons is highlighted as the current setting for 
SMB...

37 Viewing or Configuring the SMB Host Name or WINS Server with Internet Services
1. Open your Web browser and enter the TCP/IP address of the Device in the Address or Location field.  
Press Enter.
2. Click the Properties Tab. 
3. Click the plus symbol (+) to the left of Connectivity, then the Protocols file folder.
4. Select Microsoft Networking in the directory tree.
5. The available selections include:
A drop-down menu for Transport.
A text box indicating Workgroup name.
A text box indicating the SMB...

38 Note regarding DNS/WINS NetBIOS Name Resolution
To use the Devices NetBIOS name over the TCP/IP Network, the DNS and WINS Servers MUST be 
configured for NetBIOS name to IP address resolution.  Also, make sure that the Device is informed of the 
addresses of the DNS/WINS Servers, using the instructions supplied  in the TCP/IP Dynamic Addressing 
and Microsoft (NetBIOS over IP) Networks topics of this guide.
To Set Up a Workstation to Print Directly to the Device
Refer to the set up instructions...