Anaheim HMIPLC Release note for Version 16 all20110601 Users Guide

							
 
2 Support the input support of Chinese and English , click the CH key to switch the 
input method, as shown in  the followings    picture: 
 
 
If the pop up window calls the keyboard, don’t select the Clipping  in 
the Pop up Window Type . 
 
33 Tag Cross border Check 
Tag Cross border Check  in Tag ,  this function is used w hen tag is too long, or 
Multilanguage , because the lengt h of tag is different in different languages. The  Tag 
Cross border Check is  selected in default.   
And if the Tag Cross border Check is  selected, when the length of tag is exceed the  
						

							
border of component, the component will be lengthen, and display all the content of tag ,  
If  uncheck the  Tag Cross border Check,  when the length of tag is exceed the 
border of component, the component will not  be lengthen, the content that exceed the 
border is clipped. The effects of select and uncheck the  Tag Cross border Check are 
shown in the followings pictures: 
 
 
  
						

							
 
34 Modify the font entirely 
Select the components that need to change font, use the tools in Font Toolbar and 
Tag Toolbar  to change the tag font. 
 
35 Switching to the lowest secu rity level when window closed 
If set the security level to a window, and clear the password when window closed, the 
password is required again when enter the wi ndow. If in the V1.5 or lower version ,a 
Multiple State Setting component is required  to achieve this function, the address is 
LW9043,  Setting Mode  is Set at window Open ,  Set Value is 0 
In V1.6 add a function of  Switching to the lowest security level when window 
closed,  the security level is 0 when the windo w closed. The setting is as follows: 
 
36 Muti-Copy  
						

							
1 Add a new Copy Type called Pitch  in Muti-Copy,  as follows: 
 
The difference between the  Copy Type: Pitch and  Interval 
Interval: Begin copying at the right outer border of component   
 
Pitch: Begin copying at the  top left of component 
 
2 Add  Decrease  to the Address Auto Change Mode, the address range is from 
1~9999.  
						

							
37 System Scroll Bar Width 
The components have scroll bar themselves, for example Operation Log, the scroll 
bar width can be set by the  System Scroll Bar Width  in HMI Extended Attributes. As 
follows: 
 
The  System Scroll Bar Width  ranges from 20 to 120 pixels. And the effect is obvious 
if the interval is bigger  than 4.For example ,24,28 32. 
38 The components correspond to F1 to F12 on the keyboard 
 This function is only suitable  to the HMI that support USB host  
						

							
 
HMI that support the USB host can connect a external keyboard, and every setting 
component can corresponds to one of  F1 to F12 on the keyboard. 
39 Number Input/Text Input/Text Display/Note Book component 
The improvements of Number Input/Text Input/Text Display/Note Book 
component are as followings: 
Read Address  and Write Address  can be the same or different.  
						

							
 
2 Attribute page of  Keyboard Setting 
 
Public Window Keyboard: Use the public window keyboard,  it is the same as V1.5. 
all the Number Input component call the keyboar d inn window 3. And the default is use the 
Public Window Keyboard  
						

							
Specified Keyboard: call a specified keyboard. Note : chose the  Keyboard page in 
the  Window Attribute  , so that the window where the keyboard set can be saw  in the 
Specified Keyboard list. 
Keyboard Pop-up Position:  9    positions are available to select 
Not Use Pop-up Keyboard:  only suitable for HMI that support USB host, and input 
number via the external keyboard. 
Use Input Order:  please refer to the Use Input Order  part 
Then introduce the new functions of Text Input/Text Display/Note Book  component 
next ,as shown in the followings picture: 
 
High byte and low byte swaps:  swap the positions of MSB and LSB of a same byte 
 
Unicode: can display multi-languag e  
Extended Ascii: if checked, display the extended  ASCII characters from 0X80 to 
0Xff in ASCII code . The  Text Input/Text Display/Note Book  component can not display 
Chinese if select this function. It is mutually exclusive to the  Unicode. 
40 Use the Local Register conveniently   
If the user want to use or check the local registers, select the System register in the 
bit or word components, all the local bi t or word registers are listed in the Addr. Type. As  
						

							
shown in the followings figure: 
 
41 Install the USB driver automatically 
USB driver in EV5000 V1.6 has passed the Microsoft certification, so the USB 
software is installed automatically  when inst alls the EV5000, you needn’t to install it 
manually.  
42 Customize the CAN co mmunication protocol   
  EV5000 V1.6 supports customizing the CA N communication protocol, the user can 
write his CAN communication protocol . The related saving path is in doc of EV5000 
installation catalog , and the PDOManager is  also in EV5000 installation catalog. 
 
43 Open the multiple projects and copy/paste among different projects: 
Double click the shortcut of EV5000 or double click the exe file in EV5000 installation 
catalog twice , as shown in the followings figure:  
						

							
 
Open two projects of different names, copy a project to the other by the ways of 
shortcut CTRL+A or C ，CTRL+V, or click the menu  Edit >>> Copy/ Past 
44 EvDownload box 
As shown in the picture: 
 
Each function is as follows: 
1 Data File:  Download current project 
2 Recipe File: Download the .rcp file in the project  if there is a rcp file in the project 
3 LOGO File: Download the initial window picture  .logo file. If the user changes the 
picture in the  Edit Initial Window,  you should select this option  ,so that the initial window 
you edit can be shown. 
4 Clear Recipe:  Clear all the data in the recipe register, if the Recipe Data 
component is garbled, select this  function to clear the recipe card. 
5 Clear History Event Data: Clear the events that saved in HMI 
6 Clear History record Data:  Clear the record data that saved in HMI  
Clear ERW Data: Clear the data that saved in ERW register