Christie Projector Roadie 4K35 User Manual

Running the projector interrogator
The interrogator captures diagnostic information Christie personnel uses to help diagnose and correct
projector issues.
If a projector issue cannot be resolv
ed, Christie personnel may request an interrogator file from the
projector. Log files are compressed into a standard zip file.
1. On the touch panel controller, tap  Admin > Interrogator .
2. Tap Create File .
3. Click Continue.
4. In the Choose destination directory dialog, navigate to the location where you want...

Specifications
Learn about the product specifications. Due to continuing research, specifications are subject to
change without notice.
Display
Learn about the displa
y specifications.Panel resolution and refresh rate
Pixel format (H x V square pixels)
4096 x 2160
Processing path 23.97 - 60 HzAchievable brightness (measured at screen center)

White point
Nominal white (full white, after calibration) y = 0.351 

RS422
Bit rate 115,200 bps
Data format 1 start bit, 8 data bits, 1 stop bit, no parityRS232 IN
Connector
9-pin subminiature D, female
Bit rate 115,200 bps
Data format 1 start bit, 8 data bits, 1 stop bit, no parityRS232 OUT
Connector 9-pin subminiature D, male
Bit rate 115,200 bps
Data format 1 start bit, 8 data bits, 1 stop bit, no parityLamp power supply (LPS)
Control port
Interface RS232
Connector at lamp power supply end 9-pin subminiature D, male
Interlock port
Interface +5V TTL-compatible,...

Location
Warning
(

Location
Warning RPM
Electronics exhaust (fan 2) 3400
Liquid cooling radiator (fan 3) 1800
Image processor scaler (fan 13) 5100
Liquid cooling pump (fan 14) No software feedback
Igniter (fan 16) 6000
IMCB (fan 18) 6000
Red FPGA blower fan (fan 19) 4800
Firewall fan (fan 20) 3300Warning threshold for liquid cooling module
Learn the w arning thresholds (in RPMs) for the liquid cooling components. Location
Warning
Flow meter 0.2 mL/min
Liquid cooling pump 180 RPMTouch panel controller
R
 eview the...

Projection head
Rated input voltage 200 - 240 VAC
Rated line frequency 50 - 60 Hz nominal
Inrush current 70 A maximum
Rated current 7 A maximum (at 200 VAC)
Power consumption 1400 W maximum
Recommended circuit breaker for installation (wall
break er) 15 ALamp Power Supply power 
specifications
Learn the lamp power supply power requirements for the projector .8 kW Lamp Power Supply
Rated input voltage  Low line: 200 - 230 VAC
High line: 380 - 415 V

AC
Number of phases 3
Rated Line frequency 50 - 60 Hz...

8kW Lamp Power Supply
CDXL-20SP 1400W - 2000W
CDXL-30 2000W min., 3000W nom., 3300W max.
CDXL-30SP 2100W - 3000W
CDXL-45 2300W min., 4500W nom., 4950W max.
CDXL-45SP 2300W min., 4500W nom., 4950W max.
CDXL-60 2750W min., 6000W nom., 6600W max.
CDXL-60SP 2750W min., 6000W nom., 6600W max.
NOTE The lamp power supply is current regulated to a maximum of 180 A. Therefore the maximum power
specification for a given lamp may not be achievable until the lamp has aged, as lamp voltage increases with
hours of...

Description
Dimensions
LPS weight As installed: 52 kg (113 lbs)
As shipped with packaging: 72 kg (157 lbs)
Operating position
Rotation about projection axis +90 degrees maximum (lamp door down), -15 degrees
maximum
Tilt of projection axis from horizontal (upright mode and
portr ait mode)