Comdial Dsu II LCD Speakerphone Station Users Guide

7.7 Activating The Call Forward
Outside System (CFOS) Feature
The Call Forward Outside System (CFOS) feature gives DSU II station
users the ability to forward line calls to a remote location outside the
system. CFOS remains in effect in the event of a loss of power or a
system reset.
·To activate the CFOS feature,
1. PressINTERCOMS07.
2. Press the speed dial button programmed with the target number,
—OR—
Press a line button,
—OR—
Dial0for the Prime line or last used line,
—OR—
Dial1–4Line Group number....

7.8 Listening To A Call Over The
Speaker (Group Listening)
You can turn on the telephone speaker while you have the telephone
handset lifted if you wish. The distant party’s voice then sounds over
the telephone speaker as well as the handset; however, only your
handset microphone is active.
·To do this while on a call,
1. Press and holdSPEAKERfor two seconds.
—OR—
press pre-programmed group listening button.
·To cancel group listening,
1. Press and releaseSPEAKERto end.
7.9 Making a Paging Announcement...

·To page through system telephones (all-call and zone paging),
1. Lift handset.
2. PressINTERCOMand dial all-call or zone number:
84, 85,or86=zones1,2,or3
87= all-call.
3. Make announcement.
4. Hang up handset or wait for an answer.
·To answer telephone paging from any station,
1. Lift handset,
2. PressINTERCOM,dial88, and meet paging party on line.
·To enable the Tracker pager at your station,
1. PressINTERCOM.
2. DialS06.
·To disable the Tracker pager at your station,
1. PressINTERCOM.
2. Dial#06.
·To...

·To park a call and have Tracker Pager tell someone
to retrieve the call,
1. Answer call and pressTRANSFER/CONFERENCE.
2. Dial extension and hear ringback.
3. PressTRACK(or dial#01).
4. Your display shows park orbit (91–99) and then
returns to idle*.
Hang up handset or pressSPEAKERto end. The Tracker paging
system will transmit orbit dialing code and caller ID information,
if available, to called party’s Tracker Pager display.
(Alpha/numeric models display #91 through #99 while
numeric-only models...

7.10 Muting Your Telephone
·To mute your telephone,
1. Press and engageMUTE(MUTE light turns on).
·To return to the distant party,
1. Press and disengageMUTE(MUTE light turns off).
7.11 Setting A Do Not Disturb
At Your Telephone
·To enable do not disturb, proceed as follows:
1. PressOPTIONS.
2. PressNEXTuntilDNDis displayed.
3. PressDND.
4. PressON.
5. PressSPEAKERto end.
·To disable the do not disturb condition, repeat the above
procedure, but pressOFFinstead ofON.
GCA70–281 Using The Other Telephone...

7.12 Setting The Volume Control
Your telephone has a volume control switch. This is a multipurpose
control that you can use to set the volume of the ringer, the speaker, the
handset, the headset, and the group listening mode. Your LCD displays
the new setting when you press the volume button.
NOTE: Impact 8324S-**, 8324F-**, and 8312S-** telephones support
the optional ICVOL-** handset. The ICVOL-** is an
amplified handset with its own volume control, making it
useful in noisy environments. For ordering...

When you change the loudness, that change remains in effect until you
change it again (referred to as default setting).
·Set the speaker, headset, handset, or group listening loudness for
all future calls using the following steps:
1. PressINTERCOM.
2. Choose speaker, headset, handset, or group listen mode to be
affected.
3. While in that mode, pressVO LU M E U PorVO LU M E D OW Nto
adjust loudness.
4. DialSS5to hold the loudness at the last setting for all future
calls (until it is changed again).
5....

7.14 Switching Between Pulse and Tone
•To convert to tone while dialing — If the local telephone service is
pulse (rotary)
1. Press#at point in dialing sequence where conversion to tone is
required.
NOTE: Pulse/Tone switching can be programmed into memory keys by
pressing#during number storage.
7.15 Using Background Music
·To turn the music on,
1. PressOPTIONS.
2. PressNEXT.
3. PressMUSIC.
4. PressON.
5. PressSPEAKERto end (theSPEAKERlight turns on when
background music is on).
6. Adjust the loudness of...

7.16 Using the Recall/Flash Feature
•If your system has been configured for flash,
1. PressTA Pto generate a timed flash signal while on line.
•If your system has been configured for recall,
1. PressTA Pto disconnect as if you had hung up.
7.17 Using Toll Restriction Override
•To use Toll Restriction Override at a station,
1. PressINTERCOM.
2. DialSS6.
3. Dial your station extension number.
4. Dial your TRO code number (TRO code is not displayed —
instead anSis shown).
5. Within 15-second timeout period,...

7.18 Operating Your Telephone
As A Departmental Station
If your telephone is within a departmental group of telephones, you can
place your station in either an off-duty or a wrap-up mode.
Theoff-duty modeis when you leave your telephone for lunch or for
an extended time period and want another department telephone to
receive your calls.
Thewrap-up modeis when you need time after a call to complete
related paperwork and want another department telephone to receive
your calls. To use the wrap-up mode, you...