Home > Epson > Printer > Epson AcuLaser 2600DTN User Manual

Epson AcuLaser 2600DTN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson AcuLaser 2600DTN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 473
    							Installing Options301
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    5. Secure the Hard Disk Drive with the four screws provided.
    c
    Caution
    You should not remove any modules from the circuit board. 
    Otherwise, the printer will not work.
    6. Plug the connection cable into both the socket on the HDD 
    and that on the board as shown below.
     
    						
    							302Installing Options 7. Reattach the cover to the back side of the printer and secure 
    it with the four screws.
    To confirm that the option is installed correctly, print a Status 
    Sheet. See  Printing a Status Sheet on page 370.
    Note for Windows users:
    If EPSON Status Monitor 3 is not installed, you have to make settings 
    manually in the printer driver. See  Making Optional Settings on page 
    98.
    Note for Macintosh users:
    When you have attached or removed printer options, you need to delete 
    the printer using Print Setup Utility (for Mac OS X 10.3), Print 
    Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), 
    and then re-register the printer.
    Removing the Hard Disk Drive
    c
    Caution:
    Before you remove the Hard Disk Drive, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
     
    						
    							Installing Options303
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    w
    Warning:
    Be careful when working inside the printer as some components 
    are sharp and may cause injury.
    Turn off the printer and perform the installation procedure in 
    reverse.
    Memory Module
    By installing a Dual In-line Memory Module (DIMM), you can 
    increase printer memory up to 512 MB. You may want to add 
    additional memory if you are having difficulty printing complex 
    graphics.
    This printer has two memory slots, but one slot has a 64 MB DIMM 
    already installed in it at the time of manufacture. To increase 
    printer memory more than 320 MB, you have to remove the 
    original 64 MB DIMM first and then install two optional DIMMs.
    Installing a memory module
    Follow the steps below to install an optional memory module.
    c
    Caution:
    Before you install a memory module, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
    w
    Warning:
    Be careful when working inside the printer as some components 
    are sharp and may cause injury.
    1. Turn the printer off and unplug the power cord and interface 
    cable.
     
    						
    							304Installing Options 2. Remove the four screws from the cover on the back side of the 
    printer.
    3. Hold the cover with both hands and pull it toward you to 
    remove it.
    w
    Warning:
    Be careful when touching the circuit board inside the back 
    side cover since some parts may be very hot.
     
    						
    							Installing Options305
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    4. Identify the RAM slot.
    5. Insert the memory module vertically into the slot until the clip 
    comes out. Make sure that the left slot has a module at all 
    times.
    c
    Caution:
    ❏Do not force the memory module into the slot.
    ❏Be sure to insert the memory module facing the correct 
    way.
    ❏You should not remove any modules from the circuit 
    board. Otherwise, the printer will not work.
     
    						
    							306Installing Options 6. Reattach the cover to the back side of the printer and secure 
    it with the four screws.
    7. Reconnect the interface cable and power cord and turn the 
    printer on.
    To confirm that the option is installed correctly, print a Status 
    Sheet. See  Printing a Status Sheet on page 370.
    Note for Windows users:
    If EPSON Status Monitor 3 is not installed, you have to make settings 
    manually in the printer driver. See  Making Optional Settings on page 
    98.
    Note for Macintosh users:
    When you have attached or removed printer options, you need to delete 
    the printer using Print Setup Utility (for Mac OS X 10.3), Print 
    Center (for Mac OS X 10.2 or below), or Chooser (for Mac OS 9), 
    and then re-register the printer.
     
    						
    							Installing Options307
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    Removing a memory module
    c
    Caution:
    Before you remove a memory module, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
    w
    Warning:
    Be careful when working inside the printer as some components 
    are sharp and may cause injury.
    Turn off the printer and perform the installation procedure in 
    reverse.
    Interface Card
    Your printer comes with a Type B interface slot. Various optional 
    interface cards are available to expand your printer’s interface 
    options.
    Installing an interface card
    Follow the steps below to install an optional interface card.
    c
    Caution:
    Before you install the interface card, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
    1. Turn the printer off and unplug the power cord and interface 
    cable.
     
    						
    							308Installing Options 2. Remove two screws securing the interface card slot cover and 
    remove the cover.
    3. Slide and push the interface card into the slot firmly, then 
    fasten the screw as shown below.
    4. Reconnect the interface cable and power cord and turn the 
    printer on.
    To confirm that the option is installed correctly, print a Status 
    Sheet. See  Printing a Status Sheet on page 370.
     
    						
    							Installing Options309
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    8
    Removing an interface card
    c
    Caution:
    Before you remove an interface card, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
    Turn off the printer and perform the installation procedure in 
    reverse.
    P5C Emulation Kit
    The P5C Emulation kit is available as an option for this printer. 
    This module allows your printer to print documents in the PCL5c 
    printing language.
    Installing the P5C ROM module
    Follow the steps below to install the Adobe PostScript 3 ROM 
    module.
    c
    Caution:
    Before you install the ROM module, be sure to discharge any 
    static electricity by touching a grounded piece of metal. 
    Otherwise, you may damage static-sensitive components.
    w
    Warning:
    Be careful when working inside the printer as some components 
    are sharp and may cause injury.
    1. Turn the printer off and unplug the power cord and interface 
    cable.
     
    						
    							310Installing Options 2. Remove the four screws from the cover on the back side of the 
    printer.
    3. Hold the cover with both hands and pull it toward you to 
    remove it.
    w
    Warning:
    Be careful when touching the circuit board inside the back 
    side cover since some parts may be very hot.
     
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson AcuLaser 2600DTN User Manual