GTE Omni Si Database Technical Practices Issue 1 Manual

							TL-130100-1001OPERATIONRESULT(e) Trunk andstation numbers cleared from
variable display.(f) Class-of-service digits cleared if
present.
(g) TOD displayed.
4.17Extending Information Call on Outside Number, WATS Line, or
FX Line
4.17.1
Attendant Completes Call
STEPOPERATIONRESULT
1Station user requests outside number.
2Dial appropriate access code.(a) EXCL SRCE LED on.
(b) Fixed display cleared.(c) Second dial and tick tone heard.
(d) Dialed digits appear on fixed display.
3Dial outside number.(a) Ringback and optional tick tone heard.
(b) Digits appear on fixed display.
4
5Depress START/STOP pushbutton to(a) START/STOP LED off.
remove tick tone.(b) Tick tone stops.Announce call when outside party
answers.
NOTE:Disconnect can be made as soon as ringback tone heard.
6Depress POS RLSE pushbuttonto release call.(a) LOOP LED off.
(b) POS RLSE LED off.
(c) EXCL SRCE or EXCL DEST LED off if(d) 
Fked display cleared.
(e) Trunk and station number cleared from
variable display.(f) Class-of-service digits cleared if
present.
(g) TOD displayed.
5210
8107O-1 87 
						

							TL-130100-10014.17.2
Station User Completes Call
STEPOPERATIONRESULT
1Station user requests assistance to
reach outside number.(a) Acknowledge request.(b) inform station user that outside number
can be dialed from station upon hearing
outside dial tone.
NOTES:
1.If the attendant extended the station to the trunk, the station’s class of service is used
for toll restriction.
2.If the attendant wants to bypass toll restriction, the entire number must be dialed
before extending the trunk to the station.
2Dial the appropriate access code.(a) EXCL SRCE LED on.
(b) Fixed display cleared.(c) Second dial tone and tick tone heard.
(d) Digits appear on fixed display.
3Depress the POS RLSE pushbutton.(a) LOOP LED off.
(b) POS RLSE LED off.
(c) EXCL SRCE or EXCL DEST LED off if(d) 
pked display cleared.
(e) Trunk and station numbers cleared from
variable display.(f) Class-of-service digits cleared if
present.
(g) TOD displayed.
4.18Extending information Call Over Tie Line
STEPOPERATIONRESULT
1
2
Station user requests tie-line number.
Dial appropriate tie-line access code.(a) EXCL SRCE LED on.
(b) Fixed display cleared.
(c) Second dial tone and optional tick tone
heard.
(b) Digits appear on fixed display.
3Dial tie-line number of desired party.(a) Ringback tone heard.
(b) Digits appear on fixed display.
O-1 0881875210 
						

							TL-130100-1001STEPOPERATIONRESULT
4When tie-line party answers, announce
call.
NOTE:Disconnect when ringback tone heard.
5Depress lighted EXCL SRCE LED
pushbutton. .EXCL SRCE LED off.
6Depress POS RLSE pushbutton to(a) Fixed display cleared.
release from call.(b) LOOP and POS RLSE 
LEDs off.
(c) TOD displayed.
(d) Station and the Tie Line party are talking.
4.19
Attendant Conference
4.19.1Establish Conference Call for Inside Party
STEPOPERATIONRESULT1
2
3
4
NOTE:
5
6
5210Obtain all names and station numbers(a) LOOP LED on.
of conferees.(b) START/STOP LED on.
(c) POS RLSE LED on.
Depress CONF pushbutton.(a) CONF LED flashes.
(b) EXCL SRCE LED on.
(c) Attendant placed in conference.
Depress EXCL SRCE pushbutton.(a) EXCL SRCE LED off.
(b) Calling station placed in conference.
Depress the flashing CONF LED
pushbutton.(a) Variable display cleared.
(b) CONF LED on.
(c) Attendant removed from conference.
CONF LED flashing indicates that attendant is in conference bridge.
Dial number of second conferee. If
inside party, dial station number. If
an outside party, dial access code,
receive second dial tone, then dial(a) Fixed display cleared.
(b) 
Ringback tone heard.
(c) Dialed digits appear on display.
(d) START/STOP LED off.
outside number. If outside party,
depress START/STOP pushbutton.
Announce conference call when
second conferee answers.
8167O-l 89 
						

							TL-130100-1001STEPOPERATIONRESULT
7
8
9NOTE:
10
11Depress CONF pushbutton.(a) CONF LED flashes.
(b) EXCL SRCE LED on.
(c) Beak-in tone heard by conferee.
(d) Attendant placed in conference.
Depress EXCL SRCE pushbutton.(a) The EXCL SRCE LED off.
(b) Called party placed in conference.
Depress flashing CONF LED(a) CONF LED on.
pushbutton.(b) Attendant removed from conference.
Trunks that do not guarantee disconnect supervision remain in conference bridge
until last station hangs up regardless of when trunk party actually hangs up. All
trunks are removed from bridge when last station hangs up. Bridge becomes idle
and the CONF LED goes off.
Repeat Steps 5 through 10 until all
conferees have been placed in
conference bridge.Variable display cleared.
Depress POS RLSE pushbutton to re-(a) LOOP and POS RLSE LEDs off.
lease loop.(b) TOD displayed.
4.192Outside Party Connection
STEPOPERATIONRESULT
1Obtain all information concerning
conference names and station
numbers.
2Proceed as directed in Steps 2
through 10 (Paragraph 4.19.1).
O-190B/875210 
						

							TL-130100-10014.20.3Placing Call in Page Queue
STEPOPERATIONRESULTIncoming trunk call placed to
Attendant Console.
Depress flashing LED LOOP
pushbutton.
Depress PAGE 
Q pushbutton.
Depress POS RLSE pushbutton.
Depress and hold the PAGE push-
button and page the desired party.
Release PAGE pushbutton.
Dial page queue access code from
any station.
Dial attendant from any station as
an alternative to Step 7.
Depress flashing LOOP LED
pushbutton.(a) Ringing heard.
(b) LOOP LED (l-4) flashes at 120 IPM.
(a) LOOP LED on.
(b) “LOCAL” appears in fixed display field.
(c) Trunk number appears in variable
display field.
(d) START/STOP LED on.
(e) POS RLSE LED on.
(f) Ringing stops.
(g) Transmission established between trunk
and attendant.
(a) PAGE Q LED on.
(b) Trunk placed on hold in page queue.
(c) Fixed and variable displays cleared.
(a) POS RLSE and LOOP 
LEDs off.
(b) TOD displayed.
(a) PAGE LED on.
(b) Attendant access to paging system
allowed.
(a) PAGE LED off.
(b) Attendant Console disconnected from
paging system.
(a) PAGE 
Q LED off.
(b) Transmission established between
trunk and station (paged party).
(a) 
Ringback tone heard.
(b) LOOP LED (l-4) flashes at 30 IPM.
(c) Ringing heard.
(a) LOOP LED on.
(b) START/STOP LED on.
(c) POS RLSE LED on.
(d) Ringing stops.
(e) Page queue party remains.
(f) Calling station number and class of
service displayed.
(g) “INFORMATION” appears in fixed
display field.
(h) Transmission established between
attendant and calling party.
5210
8187o-1 93 
						

							--
TL-130100-1001STEP
OPERATlONRESULT
10Depress PAGE Q pushbutton.(a) The PAGE Q LED off.
(b) Three-way conversation established
,between attendant, trunk, and station.
11Depress POS RLSE pushbutton.(a) The LOOP LED off.
(b) POS RLSE LED off.
(c) EXCL SRCE or EXCL DEST LED off if
(d) 
Fked display cleared.
(e) Trunk and station identification cleared
from variable display.
(f) Class-of-service digits cleared if
present.
(g) TOD displayed.
(h) Trunk and station are connected.
42Dial attendant from any station.(a) Ringing heard.
(b) LOOP LED (l-4) flashes at 30 IPM.
13Depress flashing LOOP LED
pushbutton.(a) LOOP LED on.
(b) START/STOP LED off.
(c) POS RLSE LED on.
(d) Ringing stops.
(e) The calling station number and class of
service displayed.
(f) “INFORMATION” appears in fixed
display field.
(g) Transmission established between
attendant and station.
14Repeat Steps 3 through 7.Results same as Steps 3 through 7.
4.20.4If Paged Party Does Not Answer
STEP
OPERATIONRESULT
1Depress idle LOOP pushbutton (l-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
2Depress PAGE Q pushbutton.PAGE Q LED off
3Proceed as requested by calling
party.o-194
8l875210 
						

							TL-130100-1001
4.20.5If Paged Party Calls Attendant
STEPOPERATIONRESULT
1
2
3
NOTE:Depress flashing LED LOOP
pushbutton.(a) LOOP LED on.
(b) START/STOP LED on.
(c) POS RLSE LED on.
(d) Station number displayed in 
trunk-and-station-number display.
(e) The class-of-service digits displayed
in class-of-service display.
(f) “INFORMATION” displayed in 
type-of-call display.
After answering paged party, depress(a) PAGE Q LED off.
PAGE Q pushbutton.
(b) Three-way call established.
To release call, depress POS RLSE
(a) LOOP and POS RLSE 
LEDs off.
pushbutton.
(b) START/STOP LED off.
(c) Trunk-and-station number display off.
(d) Class-of-services display off.
(e) Type-of-call display off.
(f) TOD displayed.
If paged party dials page-answer code, paged party is automatically connected to
party in page queue. The PAGE Q LED goes off.
4.20.6
Attendant Denied Placing Call In Page Queue Condition
STEPOPERATIONRESULTIncoming trunk call placed to an(a) Ringing heard.
attendant that has PAGE Q equipped.(b) LOOP LED (l-4) flashes at 120 IPM.
Depress flashing LOOP LED(a) LOOP LED on.
pushbutton.(b) “LOCAL” appears in fixed display field.
(c) Trunk number appears in variable
display field.
(d) START/STOP LED on.
(e) POS RLSE LED on.
(f) Ringing stops.
(g) Transmission established between
trunk and attendant.
52108187o-195 
						

							.’.T I.
TL-I 3OlOO-1001
STEPOPERATIONRESULT
3Depress PAGE Q pushbutton.
4
5Depress START/STOP pushbutton.
Incoming trunk call placed to an
attendant that does not have PAGE
Q equipped.
6Depress flashing LED LOOP
pushbutton.
7Depress PAGE Q pushbutton.(a) PAGE Q access denied.
(b) Appropriate message displayed
indicating failure.
START/STOP LED off.
(a) Ringing heard.
(b) LOOP LED (l-4) flashes at 120 IPM.
(a) LOOP LED on.
(b) “LOCAL” appears in fixed display field.
(c) Trunk number appears in variable
display field.
(d) POS RLSE LED on.
(e) Ringing stops.
(f) Transmission established between
trunk and attendant.
(a) Page Queue access denied.
(b) Appropriate message displayed
indicating failure.
4.21Code Calling
4.21 .lAttendant Code Calling
STEPOPERATIONRESULT
1Depress idle LOOP pushbutton (1-4)(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
2Dial the following information:
(a) Code call access code.
(b) Zone-paging digit (if applicable).
(c) One-, two-, or three-digit code of
the called party.(a) PAGE LED on.
(b) Fixed display shows dialed digits.
3Remain with call until called partyCoded digits are heard by attendant and
answers.
over loudspeakers.
4Deliver message when called party
answers.
O-1 9681875210 
						

							TL-130100-10014.19.3
Station on Outside Party Requests Inclusion in Existing
Conference
STEPOPERATIONRESULT
1If calling party requests entry in
existing conference, depress the
lighted CONF LED pushbutton.
2Depress EXCL. SRCE LED pushbutton
if conferees are allowed entry.
3Depress flashing CONF LED
pushbutton.
4
Depress POS RLSE pushbutton to
release loop.
5Depress flashing CONF LED
pushbutton if conferees are denied
entry.
6Depress EXCL SRCE pushbutton.
7Inform calling party of reason for
entry denial. Provide assistance as
required and depress POS RLSE
pushbutton.(a) CONF LED flashes.
(b) EXCL SRCE LED on.
(c) Attendant placed in conference.
(a) EXCL SRCE LED off.
(b) Calling party placed in conference.
(a) Fixed and variable displays cleared.
(b) CONF LED on.
(c) Attendant removed from conference.
(a) LOOP and POS RLSE 
LEDs off.
(b) TOD displayed.
(a) CONF LED on.
(b) Attendant removed from conference.
(a) EXCL SRCE LED off.
(b) Attendant and calling party connected.
(a) LOOP and POS RLSE 
LEDs off.
(b) Trunk-and-station-number
display off.
(c) Type-of-call display goes off.
(d) If station call or tie-line call, 
class-of-service digits display off.
(e) TOD displayed.
4.19.4Accessing Conference Bridge 2’
 STEP
OPERATIONRESULT
1Conference bridge 1 is busy
(indicated by CONF LED on).
2Depress idle LOOP pushbutton
(1-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) Fixed display cleared.
(d) START/STOP LED on.
(e) Dial tone heard.
5210
6167
o-1 91 
						

							TL-I 30100-l 001
OPERATIONRESULTDial conference bridge 2 access
code.
(a) Fixed display cleared.(b) If conference bridge 2 is idle, CONF LED
(c) 
i:onference bridge 2 is busy, CONF
LED remains on.
(d) Dialed digits appear on fixed display.
4.20
4.20.1
Paging
Universal Paging
OPERATION
RESULT
1Depress and hold PAGE pushbutton
for duration of page or message.(a) PAGE LED on.
(b) Message or page heard over
loudspeakers.
2Release PAGE pushbutton.(a) PAGE LED off.
(b) Attendant disconnected from paging
circuit.
4.20.2Zone Paging
STEPOPERATIONRESULT
2Dial access paging code, followed by(a) PAGE LED on.
zone-paging digit.(b) Dialed digits appear on fixed display.
(c) START/STOP LED off.
3Page or provide authorized message.
4Depress POS RLSE pushbutton.(a) Fixed display cleared.
(b) LOOP, POS RLSE, and PAGE 
LEDs off.
(c) TOD displayed.
1Depress idle LOOP pushbutton (l-4).(a) LOOP LED on.
(b) POS RLSE LED on.
(c) START/STOP LED on.
(d) Dial tone heard.
o-192
81875210