GTE Omni Si Database Technical Practices Issue 1 Manual

							SW 5210TL-130500-1001
9. Dictation access circuits: No limit. No software limit exists
for the number of dictation access circuits in the system.
However, each assigned dictation access card reduces the
number of available lines by eight or the number of available
trunks by four.
10. Display telephone sets (calling/called number): The limit of
sets is the total number of stations in the switch. Stations
equipped with a calling number display cannot have the
message-waiting feature.
11. The Analog Featurephone and Digital Featurephone
maximums cannot occur simultaneously. The system
supports a maximum of 128 for a mixture of both types of
phone.8187S-l 73 
						

							TL-130500-1001Table 10.10Universal PC6 Cards Maximum System Capacities (Voice)
CARD TYPECIRCUITS PEROff-Premises Line Card
Conference (8-Party)
Attendant Interface
Dictation/Paging/Code Calling
PDTMF Receiver
Two-Wire Trunk (Two-Way Loop)
Two-Wire Trunk (Two-Way E&M)
Two-Wire Trunk
(One-Way Incoming Loop)
Four-Wire Trunk (Two-Way E&M)
FB-51267-A
4
9
Tl Access/Spam Interface
FB-17277-A or1FB-15277-l A
Tl Frame DetectorFB-15278-A1
Tl Line Compensator
FB-15280-A1
Tl Buffer
FB-171921
Tl Supervisory Circuit
FB-20718-l A1PCM Release Link Trunk
FB-17251 -A4
4
Sl Dual Modem and Loop Interface ’ FB-17209-A28Control Interface ProcessorFB-17225-A
8
16Voice Control Interface Processor
FB-17235-A
8
16Data Voice Control Interface
FB-17236-A4 
Voice/4 Data16Processor
VPLC2FB-17246-A8
8
OMNI Automatic Identification of
FB-17276-A41Outward Dialing
S-l 74
8187SVR 5210 
						

							-.:.:.TL-130500-1001
Table 10.11Voice - Data Circuit Ratios (Without a Tl Span)
8-CircuitTrunkVoice Packet
Line CardsVoice Lines Trunk Cards
CircuitsLine Card 2Data Ports
(VPLC2)
0000
15120
2161414112
6481413104
221764
16648
23184416540
22176520432
26208
520324
27216624216
SVR 5210&I37s-175 
						

							TL-130500-1001Table 10.12Voice - Data Circuit Ratios (With a Tl Span)
8 Circuit Line
CardsVoice CircuitsI
2I16
72
12I
16I128I
18I144
Trunk CardsTrunkVPLC2
CircuitsCardsData Ports
I88I
I72I
I
64
I561
3
I16II16I
S-1768187SVR5210 
						

							TL-130500-1001ORDERING THE11.0 The hardware editing sheets (FM-41460-A) used
VOICE SYSTEMfor this release must be completed to order SVR 5210. Ordering
Guide (FM-41 640) provides instructions for completing the
editing sheets. The system can be ordered as either a standard
or custom hardware configuration.
Standard Hardware11.1 The standard configuration is available in two sizes.
Configurationl 48 lines/4 trunks
l 96 lines/4 trunks
Normally a standard system is shipped within three weeks from
receipt of the order. Any additional equipment needed must be
ordered piecemeal.
Custom Hardware11.2 When ordering a custom system, order all peripheral cards
Configurationand software required. A custom configuration is shipped within
eight weeks from receipt of the order.
In addition to starndard or custom hardware, software is also
ordered as either standard or custom configuration. Whenever
possible, order a customized data base.
When ordering a custom system, fill out the frame layout
worksheet that is included in the Ordering Guide.
Submit the frame layout worksheet along with the completed
editing sheets when ordering the system.
Use the following steps and flowchart (Figure 11 
.l) when
completing the frame layout worksheet:
1. Determine quantity of each type of universal card required.
2. Determine quantity of universal card slots needed.
3. Fill in the frame layout sheet with the following:
a. If used, place 
Tl span cards.
b. Place trunk cards using preferred location first.
c. Fill remainder of double width card slots.
d. Place single height cards evenly among equipped time
groups.
e. Place line cards.
f. Place CIP cards next to line card.
g. Add any remaining single height cards.
NOTE: Use pencil when filling in this form.
SVR 5210
8187s-1 77 
						

							TL-130500-1001START
vPerform Traffic Study for
Each of the 6 Time Slot
Groups
A
NO
TDetermine if the Traffic
is Balanced
4
Figure 11.1Flowchart for Balancing System Traffic
S-l 78
8’87SW 5210 
						

							TL-130500-1001PCMUS GROUP CIFILE As
>I
5
-21-
;
-
IUP
&
Y14
-
I
EXP~~E”‘ON
(W,
+-GROUP 6 jPCMUS GROUP 
D
FILE B
II-COMMON CONTROL-If- PCM~$oGU~O~P A
Figure 11.2Frame Layout Worksheet Addressing
SVR5210
8187s-179 
						

							TL-130500-1001
NOTES: The following infirmation should be considered when
configuring a system.
l Refer to the card description section of this document, section
3.0, for information on cards required to support features to be
implemented.o Figure 11.2 provides information for determining card slots
required.
l Provide a minimum of 20% growth for the system.
l If group D is required, then an extra PCMFS and 
PCMI must
be ordered. Put a PCMFS (FB-17189) card in slot 06 and a
PCMI (FB-17187) card in slot 08 of the Expansion File.
l 
Tl span cards go into the Tl span card slots in between Cl-C6, located to the right of the PCMUS.
l Preferred locations for double width cards are:
- 11 span location when the Tl-span option is not used.
- Al 1, which provides an overhang for a double width card as
it is a heat vent
- Bll and Dll, which provide overhang into the cabinet
l Use single width location for double width cards only after
using all double width locations.
l The 
ATT12 has no overhanging parts, but due to its heat output
requires an empty slot next to it for ventilation.
e When possible the PLCC and CIP cards required to support
the Analog Featurephone should be put into card slots next to
one another. Circuits for a given IFP should also match on
both cards. Assign circuit in the following order: 4, 0, 5, 1, 6, 2,
7, 3. Circuits 0, 2, 4, and 6 of the 
DVCIP card are used for
voice, while circuits 1, 3, 5, and 7 are used for data.
l Traffic study must be done for each time slot group. Tables
11.2 and 11.3 are provided to help in determining traffic
l If the traffic study indicates that blockage will occur, the card
must be relocated.
l If the traffic study indicates a large imbalance in CCS per
group, it is recommended 
o reposition cards. In some cases,
one group may have been deliberately configured with a 
lowamount of CCS traffic, which is acceptable.
l It may be necessary to try several locations for the various
cards before a proper balance is achieved.
S-l 80
8187SVR 5210 
						

							TL-130500-1001
Table 11.1Card Parameters
MNEMONICWIDTHGUARCKTs ON
Ws)CARD PART NO.
FB-17201 -AFB-17202-A
FB-17203-A
FB-17208-A
FB-17209-A
FB-1721 O-AFB-17225-A
FB-17226-A
FB-17426-A
FB-17227-A
FB-17228-A
FB-17229-A
FB-17230-A
FB-17231 -AFB-17235-A
FB-17250-A
FB-17251 -AFB-17254-A
FB-51267-A
FB-51279-A
FB-51280-APEMT
IDoubleIPCOT
PDTMFDouble
Single
ATT12IDoubleI
SIDMLIDoubleI
PADICDoubleI0
CIPISingleI
VPLC (VPLO)
VPLC (VPLl)Single
Single
08
0
2
VPLC2 (VPLO)
VPLC2 (VPLl)Single
Single
08
02
PBEfl-ISingleI
PRADMP-ASingle
Single01
01ADMP-B
ISingleI0I1
UCB/DCP 1SingleI1
VCIPISingleIPOPS
IDoubleIIIIRLT
H44
PLCC1SingleIPFWTA
IDoubleI0”i-~4PCONF
ISingleI
IDouble
INOTE: Guaranteed 
TS(s) (Time Slot(s)) required on this card
when:
*CKT(s) control RA(s)
“CKT(s) used with ACDICAS Agent Instrument.
+ CKT assigned for M-O-H or attendant line circuit
+ + If all 24 
Tl trunks are enabled the Tl span uses all 24 TSs.If not, some 
TSs can be used for other equipment.
SVR 5210
8187S-l 81 
						

							TL-130500-1001
S-l 828i87Table 11.2 Available 
CCSs
AVAILABLE CCS
I
II
23500540I
22472510
21443480I
I1
19138814221
1  18 1  360 1  
393 1
Table 11.3 Group Traffic
GROUP TRAFFIC AT P = 0.01
Required Forms11.3 When the frame layout worksheet from the Hardware
Ordering Guide (FM-41480) has been completed, the hardware
editing sheets are to be filled out. The editing sheets contain a
listing of all software and hardware components of the system.
When completed, a copy of the editing sheets and a copy of the
frame layout workskeets are to be submitted.
NOTE: Use the frame layout worksheet, found in the 
SlHardware Ordering Guide FM-41450, when ordering a system.
SVR 5210