Honeywell 1900gsr 2 User Manual

							Xenon/Granit User Guide 271The scanner scans until a bar code has been read, until the deactivate command is 
sent, or until the serial time-out has been reached (see Read Time-Out on page 
121 for a description, and the serial command on page 284).
Reset the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate 
Custom Defaults bar code below. This resets the scanner to the custom default 
settings. If there are no custom defaults, it will reset the scanner to the factory 
default settings. Any settings that have not been specified through the custom 
defaults will be defaulted to the factory default settings.
Note:If using a cordless system, scanning this bar code also causes both the scanner and 
the base or Access Point to perform a reset and become unlinked. The scanner must 
be placed in its base to re-establish the link. If using an Access Point, the linking bar 
code must be scanned. See Cordless System Operation: Xenon 1902g/1912 and 
Granit 1911i/1981i beginning on page 41,or Cordless System Operation: Xenon 
1902g-BF beginning on page 81 for additional information.
The charts on the following pages list the factory default settings for each of the 
commands (indicated by an asterisk (*) on the programming pages).
Activate Custom Defaults 
						

							272 Xenon/Granit User Guide
Menu Commands
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage
Product Default Settings
Set Custom Defaults Set Custom Defaults MNUCDP13
Save Custom Defaults MNUCDS13
Reset the Custom Defaults Activate Custom Defaults DEFALT14
Reset the Factory Defaults - 
cordless scannersFactory Default Settings:
All Application GroupsPAPDFT&68
Reset the Custom Defaults - 
cordless scannersCustom Default Settings:
All Application GroupsPAPDFT69
Program the Interface
Plug and Play Codes Keyboard Wedge:
IBM PC AT and Compatibles with 
CR suffix (not supported by Granit 
1980i)PAP_AT15
Laptop Direct Connect with CR 
suffix (not supported by Granit 
1980i)PAPLTD16
RS232 Serial Port PAP23216
Plug and Play Codes:
RS485IBM Port 5B Interface PAPP5B16
IBM Port 9B HHBCR-1 Interface PAP9B116
IBM Port 17 Interface PAPP1717
IBM Port 9B HHBCR-2 Interface PAP9B217
RS485 Packet Mode On RTLPDF117
RS485 Packet Mode Off RTLPDF017
RS485 Packet Length (20-256) RTLMPS18
Plug and Play Codes: IBM SurePos USB IBM SurePos Handheld PAPSPH18
USB IBM SurePos Tabletop PAPSPT18
Plug and Play Codes: USB USB Keyboard (PC) PAP12418
USB Keyboard (Mac) PAP12519
USB Japanese Keyboard (PC) TRMUSB13419
USB HID PAP13119
USB Serial TRMUSB13019
CTS/RTS Emulation On USBCTS119
CTS/RTS Emulation Off* USBCTS020
ACK/NAK Mode On USBACK120
ACK/NAK Mode Off* USBACK020
Remote MasterMind for USB ReM Off REMIFC020
ReM On REMIFC120 
						

							Xenon/Granit User Guide 273
Plug and Play Codes Verifone Ruby Terminal PAPRBY20
Gilbarco Terminal PAPGLB21
Honeywell Bioptic Aux Port PAPBIO21
Datalogic Magellan Aux Port PAPMAG21
NCR Bioptic Aux Port PAPNCR22
Wincor Nixdorf Terminal PAPWNX22
Wincor Nixdorf Beetle PAPBTL22
Wincor Nixdorf RS232 Mode A 
(not supported by all Granit 
models)PAPWMA23
Program Keyboard 
Country*U.S.A. KBDCTY023
Albania KBDCTY3523
Azeri (Cyrillic) KBDCTY8124
Azeri (Latin) KBDCTY8024
Belarus KBDCTY8224
Belgium KBDCTY124
Bosnia KBDCTY3324
Brazil KBDCTY1624
Brazil (MS) KBDCTY5924
Bulgaria (Cyrillic) KBDCTY5224
Bulgaria (Latin) KBDCTY5324
Canada (French legacy) KBDCTY5424
Canada (French) KBDCTY1824
Canada (Multilingual) KBDCTY5524
Croatia KBDCTY3225
Czech KBDCTY1525
Czech (Programmers) KBDCTY4025
Czech (QWERTY) KBDCTY3925
Czech (QWERTZ) KBDCTY3825
Denmark KBDCTY825
Dutch (Netherlands) KBDCTY1125
Estonia KBDCTY4125
Faroese KBDCTY8325
Finland KBDCTY225
France KBDCTY325
Gaelic KBDCTY8425
Germany KBDCTY426
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage 
						

							274 Xenon/Granit User Guide
Greek KBDCTY1726
Greek (220 Latin) KBDCTY6426
Greek (220) KBDCTY6126
Greek (319 Latin) KBDCTY6526
Greek (319) KBDCTY6226
Greek (Latin) KBDCTY6326
Greek (MS) KBDCTY6626
Greek (Polytonic) KBDCTY6026
Hebrew KBDCTY1226
Hungarian (101 key) KBDCTY5026
Hungary KBDCTY1926
Iceland KBDCTY7527
Irish KBDCTY7327
Italian (142) KBDCTY5627
Italy KBDCTY527
Japan ASCII KBDCTY2827
Kazakh KBDCTY7827
Kyrgyz (Cyrillic) KBDCTY7927
Latin America KBDCTY1427
Latvia KBDCTY4227
Latvia (QWERTY) KBDCTY4327
Lithuania KBDCTY4427
Lithuania (IBM) KBDCTY4527
Macedonia KBDCTY3428
Malta KBDCTY7428
Mongolian (Cyrillic) KBDCTY8628
Norway KBDCTY928
Poland KBDCTY2028
Polish (214) KBDCTY5728
Polish (Programmers) KBDCTY5828
Portugal KBDCTY1328
Romania KBDCTY2528
Russia KBDCTY2628
Russian (MS) KBDCTY6728
Russian (Typewriter) KBDCTY6828
SCS KBDCTY2129
Serbia (Cyrillic) KBDCTY3729
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage 
						

							Xenon/Granit User Guide 275
Serbia (Latin) KBDCTY3629
Slovakia KBDCTY2229
Slovakia (QWERTY) KBDCTY4929
Slovakia (QWERTZ) KBDCTY4829
Slovenia KBDCTY3129
Spain KBDCTY1029
Spanish variation KBDCTY5129
Sweden KBDCTY2329
Switzerland (French) KBDCTY2929
Switzerland (German) KBDCTY629
Tatar KBDCTY8530
Turkey F KBDCTY2730
Turkey Q KBDCTY2430
Ukrainian KBDCTY7630
United Kingdom KBDCTY730
United Stated (Dvorak right) KBDCTY8930
United States (Dvorak left) KBDCTY8830
United States (Dvorak) KBDCTY8730
United States (International) KBDCTY3030
Uzbek (Cyrillic) KBDCTY7730
Keyboard Conversion *Keyboard Conversion Off KBDCNV032
Convert all Characters to Upper 
CaseKBDCNV132
Convert all Characters to Lower 
CaseKBDCNV232
Keyboard Style *Regular KBDSTY031
Caps Lock KBDSTY131
Shift Lock KBDSTY231
Automatic Caps Lock KBDSTY631
Emulate External
KeyboardKBDSTY531
Control Character Output *Control Character Output Off KBDNPE032
*Control Character Output On KBDNPE132
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage 
						

							276 Xenon/Granit User Guide
Keyboard Modifiers *Control + X Off KBDCAS033
DOS Mode Control + X KBDCAS133
Windows Mode Control + X KBDCAS233
Windows Mode Prefix/Suffix Off KBDCAS333
*Turbo Mode Off KBDTMD033
Turbo Mode On KBDTMD133
*Numeric Keypad Off KBDNPS034
Numeric Keypad On KBDNPS134
*Auto Direct Connect Off KBDADC034
Auto Direct Connect On KBDADC134
Baud Rate 300 BPS 232BAD034
600 BPS 232BAD134
1200 BPS 232BAD234
2400 BPS 232BAD334
4800 BPS 232BAD435
9600 BPS 232BAD535
19200 BPS 232BAD635
38400 BPS 232BAD735
57600 BPS 232BAD835
*115200 BPS 232BAD935
Word Length: Data Bits, Stop Bits, 
and Parity7 Data, 1 Stop, Parity Even
232WRD335
7 Data, 1 Stop, Parity None 232WRD035
7 Data, 1 Stop, Parity Odd 232WRD635
7 Data, 2 Stop, Parity Even 232WRD436
7 Data, 2 Stop, Parity None 232WRD136
7 Data, 2 Stop, Parity Odd 232WRD736
8 Data, 1 Stop, Parity Even 232WRD536
*8 Data, 1 Stop, Parity None 232WRD236
8 Data, 1 Stop, Parity Odd 232WRD836
8 Data, 1 Stop, Parity Mark 232WRD1436
RS232 Receiver Time-out Range 0 -  300 seconds  232LPT###36
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage 
						

							Xenon/Granit User Guide 277
RS232 Handshaking *RTS/CTS Off 232CTS037
Flow Control, No Timeout 232CTS137
Two-Direction Flow Control 232CTS237
 Flow Control with Timeout 232CTS337
RS232 Timeout 232DEL####37
*XON/XOFF Off 232XON038
XON/XOFF On 232XON138
*ACK/NAK Off 232ACK038
ACK/NAK On 232ACK138
Scanner-Bioptic Packet Mode *Packet Mode Off 232PKT039
Packet Mode On 232PKT239
Scanner-Bioptic ACK/NAK Mode *Bioptic ACK/NAK Off 232NAK039
Bioptic ACK/NAK On 232NAK139
Scanner-Bioptic ACK/NAK Timeout ACK/NAK Timeout
*5100232DLK#####39
Cordless System Operation: Xenon 1902g/1912 and Granit 1911i/1981i
This section applies only to cordless systems. It does not apply to corded scanners or Xenon 1902g-BF 
scanners.
Replace a Linked Scanner Override locked Scanner (Single 
Scanner)BT_RPL143
Temporary Streaming Presentation 
Mode*Temporary Streaming 
Presentation Mode OnBEPPGE246
*10 Second Timeout TRGTPM1000047
60 Second Timeout TRGTPM6000047
Base Power Communication 
Indicator*On :*:BASRED150
Off :*:BASRED050
Reset Scanner Reset Scanner RESET_50
Scan While in Base Cradle Scan in Cradle Off BT_SIC051
*Scan in Cradle On (CCB01-
010BT default)BT_SIC151
Shut Down Scanner in Cradle  BT_SIC251
Base Charge Modes Base Charge Off BASCHG051
*External or Interface Cable Power BASCHG151
External Power Only BASCHG252
Page Mode *On BEPPGE152
Off BEPPGE052
Page Pitch Range 400 - 9000 Hz (*1000) BEPPFQ####52
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage 
						

							278 Xenon/Granit User Guide
Beeper Pitch - Base Error *Razz (250) (min 200Hz) BASFQ225053
Medium (3250) BASFQ2325053
High (4200) (max 9000Hz) BASFQ2420053
Number of Beeps  - Base Error *1 BASERR353
Range 1 - 9 BASERR#53
Scanner Report Scanner Report RPTSCN54
Scanner Address Scanner Address BT_LDA54
Base Address Base Address:*:BASLDA54
Scanner Modes Charge Only Mode:*:BASLNK055
*Charge and Link Mode:*:BASLNK155
Locked Link Mode BASCON0,DNG156
*Open Link Mode BASCON1,DNG156
Unlink Scanner BT_RMV56
Override Locked Scanner BT_RPL156
Out-of-Range Alarm Base Alarm  Duration (Range 1 - 
3000 sec (*0))BASORD57
Scanner Alarm Duration (Range 1 
- 3000 sec (*0))BT_ORD57
Alarm Sound Type Base Alarm Type BASORW57
Scanner Alarm Type BT_ORW57
Scanner Power Time-Out Timer Timer (0-7200 seconds) BT_LPT058
200 Seconds BT_LPT20058
400 Seconds BT_LPT40058
900 Seconds BT_LPT90058
3600 Seconds BT_LPT360058
7200 Seconds BT_LPT720058
Flexible Power Management *Full Power BT_TXP10059
Medium Power BT_TXP3559
Medium Low Power BT_TXP559
Low Power BT_TXP159
Batch Mode Automatic Batch Mode BATENA160
*Batch Mode Off BATENA060
Inventory Batch Mode BATENA260
Persistent Batch Mode BATENA360
Batch Mode Beep Off BATBEP061
*On BATBEP161
Batch Mode Storage *Flash Storage BATNVS161
RAM Storage BATNVS061
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage 
						

							Xenon/Granit User Guide 279
Batch Mode Quantity *Off BATQTY062
On BATQTY162
Quantity Codes 0 BATNUM063
*1 BATNUM163
2BATNUM263
3BATNUM363
4BATNUM463
5BATNUM563
6BATNUM663
7BATNUM763
8BATNUM863
9BATNUM963
Batch Mode Output Order *FIFO BATLIF064
LIFO BATLIF164
Total Records Total Records BATNRC64
Delete Last Code Delete Last Code BATUND64
Clear All Codes Clear All Codes BATCLR64
Transmit Records to Host Transmit Inventory Records BAT_TX65
Batch Mode Transmit Delay *Off BATDLY065
Short (ms) BATDLY25065
Medium (ms) BATDLY50065
Long (ms) BATDLY100065
Multiple Scanner
OperationMultiple Scanner Operation BASCON2,DNG366
Scanner Name Name 1-7 BT_NAM#####66
Reset RESET_67
Scanner Name BT_NAM67
Application Work Group
Selections*Group 0 GRPSEL068
Group 1-6 GRPSEL#68
Reset the Factory Defaults: All 
Application Work GroupsFactory Default Settings:
All Work GroupsPAPDFT&68
Reset the Custom Defaults: All 
Application Work GroupsCustom Default Settings:
All Work GroupsPAPDFT69
Bluetooth Connection *Bluetooth SSP On BT_SSP169
Bluetooth SSP Off BT_SSP069
Apple Serial Port Protocol 
(SPP)PairingDEFALT;PAPMFI70
Apple SPP Auto-Connect DEFALT;PAPMFI;BT_DNG570
Bluetooth HID Keyboard Connect PAPBTH71
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage 
						

							280 Xenon/Granit User Guide
Bluetooth HID Japanese Keyboard 
ConnectPAPJKB71
Bluetooth HID Keyboard 
DisconnectPAPSPP72
Bluetooth Serial Port - PCs/
LaptopsBT_TRM0;BT_DNG573
BT Connection - PDA/Mobility 
Systems DeviceBT_TRM0;BT_DNG173
Bluetooth PIN Code BT_PIN73
Auto Reconnect Mode *Auto Reconnect On BT_ACM174
Auto Reconnect Off BT_ACM074
Maximum Link Attempts Maximum Link Attempts BT_MLA###75
Relink Time-Out Relink Time-Out (*3) BT_RLT###75
Host Command Acknowledgment Host ACK On HSTACK178
*Host ACK Off HSTACK078
Host ACK Timeout HSTATO##78
Cordless System Operation: Xenon 1902g-BF
This section applies only to Xenon 1902g-BF systems. It does not apply to corded scanners or other cord-
less systems.
Replace a Linked Scanner Override locked Scanner (Single 
Scanner)BT_RPL182
Low Power Alert Range *Low Power Alert 10-30%  LPIRAG087
Low Power Alert 10-50% LPIRAG187
Low Power Alert Flash Number Range 1-9 (*3) LPIFNO87
Interval Between Flashes Range 1-9 seconds (*2) LPIFDL87
Low Power Alert Repeat Range 1-5 (*1) LPI_NO87
Interval Between Alerts Range 10-120 seconds (*10) LPI_DL88
Low Power Alert Beep Low Power Alert Beep Off LPIBEP088
*Low Power Alert Beep On LPIBEP188
Temporary Streaming Presentation 
TimeoutRange 0 - 300000 ms (*10000) TRGTPM######91
*10 Second Timeout TRGTPM1000091
30 Second Timeout TRGTPM3000091
1 minute Timeout TRGTPM6000091
2 Minute Timeout TRGTPM12000091
3 Minute Timeout TRGTPM18000091
Base Power Communication 
Indicator*On :*:BASRED189
Off :*:BASRED089
Reset Scanner Reset Scanner RESET_89
SelectionSetting
* Indicates defaultSerial Command
# Indicates a numeric 
entryPage