HP P3015 Service Manual

							4.Release one tab (callout 1).
Figure 2-30  Remove the left cover (3 of 4)
1
5.Rotate the rear of the cover slightly away from the product, and then slide the cover toward the
front of the product to remove it.
Figure 2-31  Remove the left cover (4 of 4)
ENWW Removal and replacement procedures 67 
						

							Right-rear cover
1.Remove the rear-door assembly. See Rear-door assembly on page 62.
2. Slide the right-rear cover toward the inside of the product to release it.
Figure 2-32   Remove the right-rear cover (1 of 2)
3.Rotate the bottom of the cover away from the product, and then pull down on the cover to remove
it.
Figure 2-33   Remove the right-rear cover (2 of 2)
68 Chapter 2   Removal and replacement ENWW 
						

							Tray 1 (multipurpose tray) cover
1.Before proceeding, remove the following components:
●Rear-door assembly. See 
Rear-door assembly on page 62
.
● Left cover. See 
Left cover on page 66
.
2. Carefully release two retaining arms (callout 1).
Figure 2-34  Remove Tray 1 cover (1 of 3)
1
3.Slightly lower the cover, and then slide it toward the left side of the product.
TIP: If you lower the tray too far, it will not slide off of the hinge pins.
Figure 2-35  Remove Tray 1 cover (2 of 3)
ENWW Removal and replacement procedures 69 
						

							4.Remove the Tray 1 cover.
Figure 2-36   Remove Tray 1 cover (3 of 3)
70 Chapter 2   Removal and replacement ENWW 
						

							Cartridge-door assembly
1.Before proceeding, remove the following components:
●Rear-door assembly. See 
Rear-door assembly on page 62
.
● Left cover. See 
Left cover on page 66
.
● Tray 1 (multipurpose tray) cover. See 
Tray 1 (multipurpose tray) cover on page 69
.
TIP: The cartridge-door assembly can be removed without removing the Tray 1 cover.
However, it is easier to remove and reinstall the door assembly when the Tray 1 cover is not
installed.
2. Remove one spring (callout 1).
Figure 2-37  Remove the cartridge-door assembly (1 of 3)
1
ENWW Removal and replacement procedures 71 
						

							3.Slightly slide the assembly toward the left side of the product to release it from the hinge pins.
CAUTION: Do not damage the plastic link arm (callout 1).
Figure 2-38  Remove the cartridge-door assembly (2 of 3)
1
4.Rotate the assembly down, and then separate the plastic link arm (callout 1) from the assembly.
Remove the cartridge-door assembly.
Figure 2-39   Remove the cartridge-door assembly (3 of 3)
1
72 Chapter 2   Removal and replacement ENWW 
						

							Top-right cover
1.Before proceeding, remove the following components:
●DIMM cover. See 
DIMM cover and DIMM on page 57
.
● Formatter cover. See 
Formatter cover and formatter PCA on page 60.
2. Remove two screws (callout 1).
Figure 2-40  Remove the top-right cover (1 of 2)
1
3.Lift the cover off of the product to remove it.
Figure 2-41  Remove the top-right cover (2 of 2)
ENWW Removal and replacement procedures 73 
						

							Control panel
WARNING! ESD sensitive component.
1.Before proceeding, remove the following components:
●DIMM cover. See 
DIMM cover and DIMM on page 57
.
● Formatter cover. See 
Formatter cover and formatter PCA on page 60.
2. Press the cartridge-door release button, and then open the cartridge door. Make sure that the door
is completely open.
Figure 2-42   Remove the control panel (1 of 4)
3.Disconnect one connector (callout 1), and then remove one screw (callout 2).
Figure 2-43   Remove the control panel (2 of 4)
1
2
74 Chapter 2   Removal and replacement ENWW 
						

							4.Slide the control panel toward the front of the product to release it.
Figure 2-44  Remove the control panel (3 of 4)
5.Lift the control panel off of the product.
Figure 2-45  Remove the control panel (4 of 4)
ENWW Removal and replacement procedures 75 
						

							Front-right and right-side cover assembly
1.Before proceeding, remove the following components:
●DIMM cover. See 
DIMM cover and DIMM on page 57
.
● Formatter cover. See 
Formatter cover and formatter PCA on page 60.
● Cartridge-door assembly. See 
Cartridge-door assembly on page 71
.
NOTE: The figures in this section show the cartridge-door assembly installed. However, it
might be easier to reinstall the front-right and right-side cover assembly if the cartridge-door
assembly is removed.
● Control panel. See Control panel on page 74.
2. Remove two screws (callout 1).
Figure 2-46   Remove the front-right and right-side cover assembly (1 of 6)
1
76 Chapter 2   Removal and replacement ENWW