Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual

SUPERSET 4 Telephone Information
\
REAR
SUPPORT(OPTIONAL)
Figure 3-3 
SUPERSET 4 Telephone and Optional Support
Page 9 

SECTION MITL9109-094-107-NAPage 10 

SUPERSET 4 Telephone Information
4. FUNCTIONAL DESCRIPTION
General
4.01The SUPERSEJ 4 telephone face layout is shown in Figure 4-l.
The following describes the function of each key and display; all
keys are noninterlocking.
Line Select/Speed Dial Keys
4.02There are a total of 15 line select/speed call keys. During CDE
14 of these can be programmed as line select keys, (one key is
designated as the Prime line). Lines can be a combination of line types
such as Key, DTS, Private etc. Unassigned keys are...

SECTION MITLSI 09-094-l 07-NA
4.07 After the DISPLAY key is pressed, the actual feature to be
displayed is selected by:
Pressing a line select/speed dial key 
- for line or caller identification,
or speed dial number
ORPressing a 
softkey under the prompt associated with the feature. (To
clear the display, press the EXIT softkey).
4.08SELECT FEATURES. Features which may be activated at any
time, as opposed to those which may be selected only at fixed
times, are displayed on the features display when the...

SUPERSET 4 Telephone information
4.15FEATURES DISPLAY AREA. The words displayed in this area
indicate the features that may be selected at any time. Those
features which are not in the Class of Service are not displayed.
Display of the words is initiated by pressing the DISPLAY FEATURES
key.4.16The meaning of each feature name is as follows:
1:FWD Call Forward.
This feature is automatically invoked after setting up type and destina-
tion. To cancel the feature, the user must press the SELECT FEATURES...

SECTION MITL9109-094-107-NA5:ACC CODE Account Code.
Page 14It may be necessary for a user to enter an account code before being
allowed access to a trunk; or a user may require an SMDR record of an
account number against a call. In either case, the user must press the
SELECT FEATURES key and dial ‘5’. The account number can now be
dialed from the keypad, and the digits are displayed; no DTMF tones
are heard as signaling of the code is a data transfer function. A correct
account code is entered when the...

SUPERSET 4 Telephone Information
Message: CONSECUTIVE ERRS
Meaning: This is displayed when a series of data transfer errors has
been detected by the host PABX. If the error occurs during a call, the
audio may be lost, and the features become inoperative. If the error
occurs while the set is idle, no calls can be made or received at the
set. This error may be transient in nature and may disappear. When the
error is cleared (refer to appropriate PABX Maintenance Documenta-
tion), time and date are...

SECTION MITL9109-094-107-NALINE STATUS DISPLAY
ILINE SELECT/
SPEED DIAL KEYS
HOLD KEY
FEATURESDISPLAV
abcdefdisplay
II 0 1.1.
ghlikllll”Clselect -features
141U~
prstuvWXYspeaker on/off
1711FEATURE KEVS
Figure 4-1 
SUPERSET 4 Telephone Keys and Displays
Page 16 

SUPERSET 4 Telephone Information
ISYMBOLDESCRIPTIONMEANING
NO SYMBOL IN DISPLAVLINE IDLE
+*DISPLAV ALTERNATES
INCOMING CALL
BETWEEN THESE TWO SYMBOLS
DISPLAY SOLID SQUARELINE BUSY
AT THIS SET
DISPLAY SOLID CIRCLELINE BUSV AT
ANOTHER SET
DISPLAY ALTERNATESCALL ON HOLD
BETWEEN SOLID AND CLEARAT THIS SET
4
OISPLAV CIRCLE FLASHESCALL ON HOLD AT
ON AND OFFANOTHER SET
5634ElRl
- Figure 4-2 SUPERSET 4 Telephone Line Status Display Symbols
Page 17 

SECTION MITL9109-094-107-NAFEATURES DISPLAYALPHANUMERIC 
DlSPLPiYFEATURES
AREAAREADISPLAY AREA
\
71:FtiDr
2:NO DIST’E::::: ::::: :::::::::: ::::: :::::::::: ::.:: :::::. ..m.. . . . .. . . . .. . . . .. . . . .. . . . .. . . . .
3:AUTO ANS. . . . . . . . . . .s... :::m: ::::: ::m:: :::g: ..,.. ..,.I::::: ::::: :::::::::: ::::: ::::: ::::: ::::: ::::: :::::..*... . . . .:::::::::: p::: :p: pi; ;pEE &I pr ::::: ::::: ::w:: ..,., ..,.. . . . . . ,‘,,,::::: ::::: ::::: ::::: pi pi. . . . .. . . . .. . . . .....