Panasonic Digital Camera Dmc Zs50 Owners Manual For Advanced Features

							Wi-Fi/NFC
Operating the camera using a smartphone/tabletSQW0195
- 211 -
Adding location information to pictures in the camera
You can write the location information acquired on your smartphone to a picture recorded 
in the camera on the same date/time using the Wi-Fi function.
GPS
   Starts location information 
recording
   Ends location information 
recording
   Sends and writes the location 
information
   Start the recording
 • Location information that is different from the information acquired during recording may  be written. 

Take care regarding the following matters.
–
 Set [Home] of [World 

Time] of the camera to your home area.
–
 Once a smartphone starts recording the location information, do not change the 
[Home] setting of [World 

Time] of the camera.
 • The location information cannot be written to pictures recorded without setting [Clock Set].
 ■Recording location information and taking pictures
Start recording the location information on your smartphone
  Start “Image App”  Select [  ]  Select [  ]  Select [  Start geotagging]
Take pictures using the camera
End recording of the location information on your smartphone
  Select [  Stop geotagging] to end recording of location information
(Continued on the next page)    
						

							Wi-Fi/NFC
Operating the camera using a smartphone/tabletSQW0195
- 212 -
 ■Writing location information to a picture
Preparations:
(On the camera) Connect to a smartphone  (→194)
Operate the smartphone
  Start “Image App”  Select [  ]  Select [  ]  Select [  ]
 • Follow the messages on the screen to perform the operation.  • [  ] is displayed for pictures that have location information written to it. • You can also use [Location Logging] in the [Playback] menu to write the sent 
location information to the pictures.  (→174)
 ●Caution: 
Be sure to pay special attention to the privacy, the likeness rights, etc. of the 
subject when you use this function. Use at your own risk.
 ●You cannot add location information to the following pictures: • Pictures that already have location information • Motion pictures recorded in [AVCHD] format • Protected pictures • Pictures recorded in the built-in memory • Pictures recorded using cameras other than this unit ●Location information may not be written if there is not enough free space on your 
card.
 ●You cannot write location information to a card if the write-protect switch on the card is 
set to the [LOCK] position.
 ●For details about the operating procedure, etc., refer to [Help] in the “Image  App” 
menu.
 ●If you have changed the clock setting of this unit or the smartphone after [T ime sync], 
perform [Time sync] again. Refer to [Help] in the “Image App” menu for details.
 ●On the smartphone, you can set the acquisition interval of location information and 
check the transfer status of location information. Refer to [Help] in the “Image  App” 
menu for details.
 ●You cannot write location information when the unit is connected to a PC or printer.    
						

							Wi-Fi/NFC
Operating the camera using a smartphone/tabletSQW0195
- 213 -
Operating the camera to send pictures to a smartphone or tablet
 ■Sending method, and pictures that can be sent
JPEG RAW MP4 AVCHD 3D
Sending a picture each time one is recorded 
[Send Images While Recording] ○ – – – –
Sending selected pictures
[Send Images Stored in the Camera] ○ – ○ – –
 • Some images may not be played back or sent depending on the device. • See the operating instructions of the destination device for more information about 
picture playback.
 • For more details about picture sending methods.  (→257)
Preparation: 

Install “Image App” in advance.  (→193)
See the part of the manual that applies to your objective. 
Sending a picture each time one is recorded ([Send Images While Recording]) 
(→214)
Sending selected pictures ([Send Images Stored in the Camera]) (→216)    
						

							Wi-Fi/NFC
Operating the camera using a smartphone/tabletSQW0195
- 214 -
 ■Sending a picture each time one is recorded ([Send Images While 
Recording])
Select [New Connection] in the [Wi-Fi] menu, and press  
[MENU/SET]
 (→61)
Use cursor button to select [Send Images While Recording] 
and press [MENU/SET]
Use cursor button to select [Smartphone] and press  
[MENU/SET]
(Continued on the next page)    
						

							Wi-Fi/NFC
Operating the camera using a smartphone/tabletSQW0195
- 215 -
Select [Via Network] or [Direct] and press [MENU/SET]
 ●When connecting with [Via Network]
(On the camera)
  Connect the camera to a wireless access point (→250)
(On your smartphone)
  Set Wi-Fi function to “ON”  Select the wireless access point you connected to the camera, and set  Start “Image App” (→193)
 ●When connecting with [Wi-Fi Direct] or [WPS Connection] in [Direct]
(On the camera)
  Connect the camera to a smartphone (→253)
(On your smartphone)
  Start “Image App” (→193)
 ●When connecting with [Manual Connection] in [Direct]  (→195)
Select the device you wish to connect to
 • When the connection is established, the confirmation screen for the transmission 
setting is displayed. Check the setting and press [MENU/SET]. T o change the 
send setting, press the [DISP.] button. (→258)
Take still pictures
 • The still pictures are sent automatically after taking them. • To change the setting or disconnect, press [Wi-Fi] button.  
You cannot change the settings while sending still pictures. Wait until sending is 
complete.    
						

							Wi-Fi/NFC
Operating the camera using a smartphone/tabletSQW0195
- 216 -
 ■Sending selected pictures ([Send Images Stored in the Camera])
Select [New Connection] in the [Wi-Fi] menu, and press  
[MENU/SET]
 (→61)
Use cursor button to select [Send Images Stored in the 
Camera] and press [MENU/SET]
Use cursor button to select [Smartphone] and press  
[MENU/SET]
(Continued on the next page)    
						

							Wi-Fi/NFC
Operating the camera using a smartphone/tabletSQW0195
- 217 -
Select [Via Network] or [Direct] and press [MENU/SET]
 ●When connecting with [Via Network]
(On the camera)
  Connect the camera to a wireless access point (→250)
(On your smartphone)
  Set Wi-Fi function to “ON”  Select the wireless access point you connected to the camera, and set  Start “Image App” (→193)
 ●When connecting with [Wi-Fi Direct] or [WPS Connection] in [Direct]
(On the camera)
  Connect the camera to a smartphone (→253)
(On your smartphone)
  Start “Image App” (→193)
 ●When connecting with [Manual Connection] in [Direct]  (→195)
Select the device you wish to connect to
 • When the connection is established, the confirmation screen for the transmission 
setting is displayed. Check the setting and press [MENU/SET]. T o change the 
send setting, press the [DISP.] button. (→258)
Select [SINGLE] or [MULTI] 
 • To change the setting or disconnect, press [Wi-Fi] button.  (→190)
 ■When [SINGLE] is selected
  Select the picture  Select [Set]
 ■When [MULTI] is selected
  Select the picture (repeat) • If selected again, the setting will be canceled.  Select [OK] • The number of pictures that can be sent by 
[MULTI] is limited.
 • Confirmation screen is displayed. If you select [Yes], the operation is executed.    
						

							Wi-Fi/NFC
Displaying still pictures on a TV
SQW0195- 218 -
You can display still pictures on a TV that is compatible with a DLNA certified digital 
media renderer (DMR) function.
Preparations: Set the TV to DLNA waiting Mode.
 • Read the operating instructions for your TV
.
Select [New Connection] in the [Wi-Fi] menu, and press  
[MENU/SET]
 (→61)
Use cursor button to select [Playback on TV] and press 
[MENU/SET]
Select [Via Network] or [Direct] to connect (→249)
Select the device you wish to connect to
 • When the connection is established, the screen is displayed.
Take or play back still pictures on this unit
 • To change the setting or disconnect, press [Wi-Fi] button.  (→190)
 ●When a TV is connected to this unit, the TV screen may temporarily return to the 
status before the connection. Pictures are displayed again when you take or play back 
pictures.
 ●[Effect] and [Sound] of the Slide Show are disabled. ●Playback of motion pictures or panorama pictures, and continuous playback of group 
pictures are not displayed on a TV.
 ●During the multi/calendar playback, pictures displayed on the screen of this unit are 
not displayed on TV.    
						

							Wi-Fi/NFC
Wireless printing
SQW0195- 219 -
You can send still pictures to a compatible printer and print them wirelessly.
 ■Sending method, and pictures that can be sent
JPEG RAW MP4 AVCHD 3D
Sending selected pictures
[Send Images Stored in the Camera] ○ – – – –
 • Some images may not be played back or sent depending on the device. • For more details about picture sending methods. 
(→257)
Preparation:
 • You can print out recorded still pictures wirelessly from a PictBridge (wireless LAN- compatible) *
 printer

.
*
  Compliant with the DPS over IP standards. Contact the printer manufacturers for details on 
PictBridge (wireless LAN-compatible) printers.
Select [New Connection] in the [Wi-Fi] menu, and press  
[MENU/SET]
 (→61)
Use cursor button to select [Send Images Stored in the 
Camera], and then press [MENU/SET]
Use cursor button to select [Printer], and then press  
[MENU/SET]
Select [Via Network] or [Direct] to connect (→249)
Select the printer you want to connect and then press  
[MENU/SET]
Press [MENU/SET]
Select the still picture and print
 • Pictures are selected the same way as when connecting by USB connection 
cable. For more details  (→275)
.
 • To change the setting or disconnect, press [Wi-Fi] button.  (→190)
 ●Motion pictures cannot be printed out.    
						

							Wi-Fi/NFC
Sending pictures to AV equipment
SQW0195- 220 -
Still pictures and motion pictures can be sent to AV equipment in the home (home AV 
equipment), such as DLNA compatible recorders.
You can make a setting so that pictures in the camera can be sent to AV equipment 
automatically while the camera battery is charging. ([Smart Transfer] (→242))
Wireless access pointHome AV equipment
 ■Sending method, and pictures that can be sent
JPEG RAW MP4 AVCHD 3D
Sending a picture each time one is recorded 
[Send Images While Recording]○ – – – ○
Sending selected pictures
[Send Images Stored in the Camera] ○ – – – ○
 • Some images may not be played back or sent depending on the device. • See the operating instructions of the destination device for more information about 
picture playback.
 • For more details about picture sending methods.  (→257)
Preparations:
When sending a picture to 

AV devices, set your device to DLNA waiting Mode.
 • Read the operating instructions of your device for details.
See the part of the manual that applies to your objective. 
Sending a picture each time one is recorded ([Send Images While Recording]) 
(→221)
Sending selected pictures ([Send Images Stored in the Camera]) (→222)