Panasonic Electronic Board UB-T780 Operating Instructions

							Installation Manual (for qualified service personnel)
•Request assembly of the Electronic Board, stand and wall mounting from your dealer.
• Before assembly and construction, read this section thoroughly.
• When installing the elite Panaboard on a wall or on the stand, perform installation with 2 people.
For Your Safety
To prevent severe injury and loss of life, read this
section carefully before using the unit to ensure proper
and safe operation of your unit.
The following graphic symbols are used in this
Installation Manual. Denotes a potential
hazard that could re-
sult in serious injury or
death.
Denotes hazards that
could result in minor
injury or damage to
the unit.
These symbols are used to alert op-
erators to a specific operating proce-
dure that must not be performed.
These symbols are used to alert op-
erators to a specific operating proce-
dure that must be emphasized in
order to operate the unit safely. Notice
Safety check must be done by qualified
service personnel after installing this op-
tion.
Be sure to disconnect the power cord
while installing the unit. Otherwise, it may
cause electric shock or injury.
Be sure to use the specified parts for the
installation. Otherwise, it may cause fire,
electric shock or injury.
Notes in the operating instructions or
notes of labels on the cabinet, chassis or
parts should be observed.
Do not alter the unit and install. Installing
an altered unit can cause fire, electric
shock or injury.
Have the unit installed, removed and dis-
posed of only by qualified service person-
nel.
Operating Instructions (For Basic Operations) 29 1
Installation Manual
Installation ManualWARNING CAUTION   WARNING        
						

							After installing or moving the electronic
board, lock the casters and set the fall-
prevention extension legs.
If the unit is hung on a wall, confirm the
wall must be capable of supporting at least
the following weight.
1,005 N [103k
gf (227 lbs)] Do not attach the electronic board to mor-
tared walls. Accidental electric leakage
from the wall mounting plate bolts to metal
laths or wire laths can cause heat, smoke
or a fire.
Confirm the bolts of the unit are certainly
caught by the wall mounting plate by pull-
ing the unit after hanging the unit on the
wall mounting plate if the unit is mounted
on a wall.
Be sure to put on a glove to avoid electric
shock or injury.
30 Operating Instructions (For Basic Operations)
Installation ManualCAUTION  Locking the casters
(Push this side)
Push to lock      
						

							Included Accessories
Confirm that the following items are included with the elite Panaboard.
No. Part Name Illustration Q’ty Remarks
Power Cord
(3 m [9 ft. 10 
3
/8 in.]) 1 The illustration of the
power cord is for the Uni-
ted States. The shape of
the plug may vary de-
pending on country/area.
USB Cable
(5 m [16 ft. 5 
3
/8 in.]) 1 For computer connection
CD-ROM 1 Operating Instructions
(For Software)
Drivers
Application software
Cable Holder 1 For power cord
Wall Mounting Plate (Left) 1 —
Wall Mounting Plate (Right) 1 —
Battery (LR03 AAA alkaline bat-
tery)
1 For electronic pen
Electronic Pen 1 —
Penpoint
(Replacement)
2 For electronic pen
Cable Tie 1 Fastener for power cord
when mounted on a wall
Operating Instructions 1 Operating Instructions
(For Basic Operations)
(includes Installation
Manual)
Warranty 1 May not be included de-
pending on country/area.
Operating Instructions (For Basic Operations) 31 1
Installation Manual                         
						

							Notice
•Screws (8 count) for wall mounting are not included. Please purchase screws with a size of M6,
appropriate for your type of wall (page 35). 32 Operating Instructions (For Basic Operations)
Installation Manual 
						

							Wall Mounting Construction
Checking the Wall
When mounting on a wall, consult with your building's
 owner, caretaker or construction manager to determine
if the wall strength is sufficient to install the elite Panaboard. For safety, install the elite Panaboard only after
thoroughly understanding the type of walls, the appropriate types of screws and the construction method (Page
35). CAUTION
Do not attach the electronic board to mortared walls. Accidental electric leakage from the wall
mounting plate bolts to metal laths or wire laths can cause heat, smoke or fire.
I.Necessary Tools and Parts (not included with the elite Panaboard)
Drill, Screwdriver, Measuring tape, Level
8 screws (M6 size)
II.Before Starting
1.Make sure that the wall is strong enough to support the elite Panaboard.
Rated strength: greater than 1324 N (135 k gf)Notice
•If necessary, reinforce the wall so that it is strong enough to support the elite Panaboard.
2. Make sure that the location is large enough to accommodate the elite Panaboard.
Height: greater than 2000 mm (6 ft. 7 in.)
Width: greater than 1850 mm (6 ft. 1 in.)
3. Make sure that the AC outlet is within 3 m (9 ft. 10  3
/8 in.) of where the elite Panaboard will be
mounted and that it will not be behind the elite Panaboard. Operating Instructions (For Basic Operations) 33 1
Installation Manual 
						

							Installing the Wall Mounting Plates
1.Ensure that the wall is strong enough to support the elite Panaboard.
Rated strength: greater than 1324 N (135 k gf)
2. Using the measuring tape and level, mark the 8 locations to insert the screws. Note
•The dotted line in the illustration represents the outer edge of the elite Panaboard.
3. Drill 8 holes for the wall mounting plates.
•Drill holes that are appropriate for the screws you are using.
4. Install the wall mounting plates using the 4 screws.
•2 screws are used for each wall mounting plate.
The remaining 4 screws are used after installing the elite Panaboard on the wall. •
Screws (8 count) are not included with the elite Panaboard. Please purchase screws with a size of M6,
appropriate for your type of wall. 34 Operating Instructions (For Basic Operations)
Installation Manual813 mm
(2 ft. 8 1/8 in.)
40 mm (1 
5/8 in.)
982 mm
(3 ft. 2 
3/4 in.)
30 mm (1 
1/8 in.)
44 mm (1 
3/4 in.) 222.5 mm (8 
3/4 in.) 469.5 mm
(1 ft. 6 1/2 in.)
725 mm
(2 ft. 4 5/8 in.) 40 mm (1 5/8 in.)
982 mm (3 ft. 2
 3/4 in.)
30 mm (1
 1/8 in.)
44 mm
(1 3/4 in.) 813 mm 
(2 ft. 8
 1/8 in.)  
						

							•
Tighten the bolt so that it will not become loose.
• When drilling the holes and installing the wall mounting
 plates, follow the procedure in "Wall Types and
Installation Procedures" (page 35).
5. Mount the elite Panaboard on the wall.
See "Assembling the elite Panaboard" (For Wall Mounting  ® page 42).
Wall Types and Installation Procedures The method for attaching the wall mounting plates to the wall will vary depending on the wall's structure.
Three available options are listed below.
Other methods may be necessary depending on the wall.
Metal or Concrete wallsStud plugs (not included) are needed. Drill eight holes in the wall.
For the correct hole size, refer to the instruc-
tions for the particular stud plugs used.
Insert the bolt through the hole in the wall
mounting plate and tighten until the wall
mounting plate is securely fixed to the wall.
Operating Instructions (For Basic Operations) 35 1
Installation ManualDrill bit
Metal or concrete 
wall
Stud plug
Wall mounting
plate
Bolt
Insert a stud plug in the hole.  
						

							Plasterboard walls
Split-wing toggles (not included) are needed. Insert the bolt through the hole in the wall
mounting plate and into the hole in the wall
so that the arms of the split-wing toggle are
horizontal.
For the correct hole size, refer to the instruc-
tions for the particular split-wing toggles
used.
After the arms expand, pull the wall mount-
ing plate out until the arms of the split-wing
toggle grip firmly into the wall.
Tighten
 the bolt until the wall mounting plate
is securely fixed into the wall.
Wooden walls Wood screws (not included) are needed. Insert the wood screw through the hole in the
wall mounting plate and tighten until the wall
mounting plate is securely fixed to the wall.
For the

 correct hole size, refer to the instruc-
tions for the particular wood screws used. 36 Operating Instructions (For Basic Operations)
Installation ManualPlasterboardSplit-wing toggleWall mounting
plate
Bolt
Arms
Arms Wall mounting plate
Wood screw
Wooden wall  
						

							Stand Assembly (Sold Separately)
Included Parts
Check that the following parts are included with the stand (KX-BP061).
No. Part Name Illustration Q'ty
Stand Base 2
Support Beam 2
Side Bar (A) 2
Side Bar (B) 1
Screw (M6 ´ 45 mm [1 
3
/4 in.]) 10
Two-wing Bolt (M5 
´ 12 mm [1
/2 in.]) 2
Support Bracket 2
Fall-prevention Extension Leg 4
Screw (M6 ´ 60 mm [2 
3
/8 in.]) 4
Nut 4
Wrench
*1 1
Washer 10
*1
The included wrench is necessary for tightening and loosening the screw ( ), so keep it in a safe location.
Operating Instructions (For Basic Operations) 37 1
Installation Manual                          
						

							CAUTION
Before assembly, be sure to lock the casters. Assembly Instructions
1.Assemble the fall-prevention extension legs. 38 Operating Instructions (For Basic Operations)
Installation ManualLocking the casters
(Push this side)