Panasonic Multi Hybrid Control Panel Aw Rp505 Operating Instructions

-29-
GRAY
YELLOW
CYAN
GREEN
MAGENTA
RED
BLUE
100
  90
  80
  70
  60
  50
  40
  30
  20
  10
    0
–10
–20
–30
–40+69 +77
+56
+48
+38
+12
+7
–5
–16 –16+15 +28 +36
+20
–20 +20
–20+100 +100
+89
+77
+72
+46 IRE
100% 75%
1V[p-p]
+100
+27
+27
-20
–13 –13
100
  90
  80
  70
  60
  50
  40
  30
  20
  10
    0
–10
–20
–30
–40IRE
75%
100%
+20
–20+20
–20 +7.5 +7.5
-I   WHITE  +Q       BLACK
1V[p-p]
Color Monitor
Color MonitorWaveform Monitor
Waveform Monitor
• Genlock AdjustmentTo use the camera in external sync...

-30-
eSet G/L PHASE ON/OFF Switch !5back to the OFF
position.ON SC H
OFF
G/L PHASE
90° 180°
0°      270°
External genlock
input signal
(black burst
sighal)
Video signal
G/L PHASE H Control
G/L PHASE
ON/OFF Switch
eSet G/L PHASE ON/OFF Switch !6back to the OFF
position.
Magenta Green
Cyan
Yellow
White
Red
Blue
Black
ON SC H
OFF
G/L PHASE
90° 180°
0°      270°
G/L PHASE ON/OFF Switch
G/L PHASE Coarse Switch
G/L PHASE SC Control
Color bar of
camera
Color bar of
special Effects
generator Split line...

-31-
•Total Pedestal AdjustmentTotal pedestal adjustment is made to adjust the
pedestals of two or more cameras.  Using an oscillo-
scope or a waveform monitor, adjust the pedestals to 5
IRE (0.035 V) or 7.5 IRE (0.050 V) with T.PED Control
@0.
T.PED
CABLE COMP
YC
T. PED Control
5 IRE (0.035V) or
7.5 IRE (0.050V)
3) Set the switches for gain, shutter, etc. as appropriate
to the conditions of using the camera.
4) Set the camera control switch on the multi hybrid con-
trol panel to the OFF position.
5)...

-32-
wPick up a white object (a white wall or white handker-
chief, for example) fully on the screen.  Be careful to
keep a shiny or bright object out of the screen.
eWhen AWC Switch !2of the multi hybrid control panel
is pressed, the auto set LED flashes and the white bal-
ance is automatically adjusted.  It goes out when it has
been properly adjusted.  If the adjustment fails, the
LED remains lit.  In such a case, change the bright-
ness, iris, object, light source, etc. and adjust it again.
•...

-33-
5. Camera and Pan/tilt Head Presetting1) Select a desired operating camera and pan/tilt head
with the CONTROL switch @2.
2) Pick up a desired object with the camera using
PAN/TILT Lever #8ZOOM Lever #6and FOCUS Lever
#7Select a white balance control mode using
AUTO/ATW ATW Switch oAUTO/ATW A Switch !0or
AUTO/ATW B Switch !1.  To store iris data in the mem-
ory, set IRIS AUTO/MANU Switch @5to the MANU posi-
tion and turn the iris control.  When IRIS AUTO/MANU
Switch @5is in the AUTO position, iris...

-34-
RACK MOUNTING
Holes for connecting plate
Connecting plateRack angle
nRack Mounting
Mounting ScrewMounting Screw 

-35-
nHow to Change Rear Panel DirectionqRemove the four screws from both sides of the top
cover, and take the top cover off.
wRemove the two screws and take the blank panel off.
eLoosen the rear panel screw, turn the rear panel down,
and fasten it to the bottom.
rFasten the blank panel back to the rear.
Rear panel Remove the top cover.
4 screws (on both sides)
2 screws (on both sides)
Blank panelBlank panel
Rear panel 

-36-
SPECIFICATIONSSource Voltage 12 V DC (DC jack)
Power Consumption 12V, 0.5A
Preview Video Input 1.0 V[p-p] composite/75½(BNC connector)
Genlock Input 1.0 V[p-p] black burst
75½loop through with auto terminator (BNC connector)
Preview Video Output 1.0 V[p-p] composite/75½(BNC connector)
Genlock Output 75½(BNC connector)
Camera Control Output Control signal (BNC connector)
Pan/tilt Control Output Control signal (RJ-45 8P modular jack)
System Tally Input Tally signal (6 pin Terminal block)
Auxiliary...

-37- Dimensions 210 (W) x 88 (H) x 177 (D) mm [8-1/4 (W) x 3-1/2 (H) x 7 (D)]
Weight 2.2 kg (4.9 lbs.)
Finish AV Ivory painting
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.
ACCESSORIESSeal ........................................................ 1
Rack angle .............................................. 2
Connect plate ......................................... 1Mounting screws .................................. 12
M4 x 8mm...

N1197-0 7J1A106A Printed in Japan
Broadcast & Television Systems Company
Division of Matsushita Electric Corporation of AmericaExecutive Office:One Panasonic Way 2E-6, Secaucus, NJ 07094
Regional Offices:
EASTERN ZONE:43 Hartz Way, Secaucus, NJ 07094 (201) 348-7620
CENTRAL ZONE:1707 North Randall Road, Elgin, IL 60123 (847) 468-5200
SOUTHERN ZONE:
Atlanta Region:1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30174
Panazip 11 (770) 338-6841, fax (770) 338-6741
Law Enforcement Video Products:1225...