Panasonic Pt D9610U Projector User Manual

41
Selecting the signal of ET-MD95VM2(sold separately)
When using the projector with the optional ET-MD95VM2 Video Input Module, select the appropriate video signal
format that matches the video equipment you are using.
Setting procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP  ( ) and DOWN ( ) arrow buttons to select OPTION..&/6
650 4&561
-&/4
1*$563&
104*5*0/
015*0/
4*(/- -*45
5&45 155&3/
.&/6 
46#
.&/6  &/5&3
&9*5  .&/6
Press the ENTER button. ... The OPTION...

42
Registering input signal data
Because the projector has no factory pre-set data of input signals, be sure to register input signal data before 
first use.
• Up to 64 different input signals can be registered.
• Input a signal according to an input module installed on the projector and register the signal data.
Registration new signal 
• If a new signal is input and MENU key of the remote control unit or projector operating panel buttons are pressed,
the new signal registration screen shown below will...

43
When the memory does not allow new signal registration because it is full
• When a total of 64 signals has already been registered and the memory is full, inputting a new signal and pressing
the MENU button on the remote control unit or the projector operating panel will display the overwriting registration
screen below. In this case, to register the new data, an existing signal will be cleared and overwriting with the new
data.
Overwriting registration procedure
Press the MENU button. ... The...

Sub-memory
44
This equipment has a sub memory function which enables storage of multiple image adjustment data sets, even
when the signal is determined to be the same due to the frequency and form of the synchronization signal source.
Use this when image adjustment (like aspect switching or white balance) is necessary due to the same signal
source.
The sub-memory contains all data which can be adjusted for each signal, such as the image aspect ratio and
adjustment video data (brightness, contrast etc.)...

45
On-screen display
Input switching/Signal switching
This displays the stored signal name for the STATUS screen during signal switching.
Stored signal details
3(#
*/165

/P
/.&
 YYY
*%

--
4*(/-
45564
/.&YYY
.&.03:/P 
44/P 

46
Using the RGB REALITY mode
The RGB REALITY mode is a mode for converting RGB (primary color) input signals to component signals,
performing high picture quality playback using image conversion processing specially for moving pictures.
You can choose the RGB mode best suited for the type of RGB signals you are using (refer to page 40):
RGB mode:  Choose this mode when the RGB signal source is a PC or other computer-based device that focuses
on still images.
RGB REALITY mode:  Choose this mode when the...

47
Adjusting the picture automatically
The automatic adjustment (AUTO SETUP) is a function to automatically adjust the resolution, clock phase, and
picture position when inputting an analog RGB signal consisting of dots like a computer signal. (The input of a
moving picture signal or any signal other than analog RGB signals cannot enable this function.)
It is recommendable for the automatic adjustment to input a picture signal including a brighter white box around the
outside of the perimeter of a basic...

48
2. Special signal automatic adjustment
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the LEFT (
) or RIGHT( )arrow buttons once time.
... The AUTO SETUP MENU screen will be displayed.
Press the LEFT (
) and RIGHT( )arrow to switch to desired MODE.
•STANDARD -----
When receiving signals with an image aspect of 4:3 or 5:4
•WIDE --------------When receiving signals with a wide image aspect of 16:9
•USER ------------- When receiving a special horizontal...

49
Signals which cannot be adjusted automatically should be adjusted manually. The following settings can be
adjusted manually, and the respective adjustment procedures are given below.
1.Input signal resolution data
2.Clock phase
3.Picture position
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP  ( ) and DOWN ( ) arrow buttons to select POSITION.
Press the ENTER button. ... The POSITION screen will be displayed.
Press the UP  ( ) and DOWN  ( ) arrow...

50
If a flicker or bleeding of the contour appears on the screen, adjust the clock phase to obtain an optimum picture.
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP  ( ) and DOWN ( ) arrow buttons to select POSITION.
Press the ENTER button. ... The POSITION screen will be displayed.
Press the UP  ( ) and DOWN ( ) arrow buttons to select CLOCK PHASE.
• The clock phase can be adjusted when an RGB signal has been input with
the analog RGB module...