Panasonic Pt D9610U Projector User Manual

51
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP  ( ) and DOWN ( ) arrow buttons to select POSITION.
Press the ENTER button. ... The POSITION screen will be displayed.
Press the UP  ( ) and DOWN ( ) arrow buttons to select SHIFT.
Press the ENTER button. ... The SHIFT screen will be displayed.
Press the UP, DOWN, LEFT and RIGHT (
, , and ) arrow buttons to
adjust the picture position.
Press the MENU button three times.
• The on-screen display will...

52
Adjusting the blanking
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION.
Press the ENTER button. ... The POSITION screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select BLK.
Press the ENTER button. ... The BLK screen will be displayed.
Press the control level buttons ( +and −) to select the desired BLK mode from
those indicated below.
UPPER, LOWER, LEFT, RIGHT
Press the UP ( ) and...

53
• If the black portions of the picture are fractured or tinged with green, adjust the clamp position its optimum
state.
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION.
Press the ENTER button. ... The POSITION screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select CLAMP POSITION.
• The clamp position can be adjusted when an RGB signal has been input with the
analog RGB module...

54
• The KEYSTONE adjustment allows you to compensate for pictures’ horizontal trapezoidal distortion. 
(Keystone adjustment can not carried out in built-in test pattern.)
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION.
Press the ENTER button. ... The POSITION screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select KEYSTONE.
Press the ENTER button. ... KEYSTONE screen will be...

55
Adjusting the picture to the desired setting
The following procedures can be used to adjust the picture to the desire appearance.
Adjustment procedure ... Adjusting the COLOR setting
Press the MENU button. ... The MENU screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE.
Press the ENTER button. ... The PICTURE screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select COLOR.
Press the ENTER button. ... The COLOR individual adjustment screen will...

56
Adjusting the white balance (High / Low)
Adjustment procedure (Project a signal to be adjusted)
Press the MENU button. ... The MENU screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE.
Press the ENTER button. ... The PICTURE screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select COLOR TEMP.
Press the LEFT ( ) and RIGHT ( ) arrow buttons to select the desired setting
from those indicated below.
LOW, MID, HIGH, USER, DYNAMIC
〈
If you would...

57
NOTE
Adjusting the picture quality
The following procedures can be used to adjust the picture quality to the desired setting.
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select PICTURE.
Press the ENTER button. ... The PICTURE screen will be displayed.
• If a  or  indicator is shown at the bottom or top of the adjustment items
list in the PICTURE window, it indicates that the remaining part of the list can
be scrolled...

58
• NR (noise reduction) settings cannot be adjusted for analog RGB input and TMDS input.
• The FILTER adjustment is ineffective for XGA (1 024 x 768) mode on the PT-D9510U, or SXGA (1 280 
x 1 024) mode on the PT-D9610U. It is also ineffective for any video input mode other than analog 
RGB and TMDS modes, or if “THROUGH” is chosen for the SIZE mode (see pages 60 and 61).
• Even with the above signal, adjustment is possible during keystone correction. Even with YUV type 
signals, adjustment is possible...

59
Adjusting the picture size
Adjustment procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select POSITION.
Press the ENTER button. ... The POSITION screen will be displayed.
Press the UP ( ) and DOWN ( ) arrow buttons to select SIZE.
Press the ENTER button. ... The SIZE screen will be displayed.
Press the control level buttons ( +and −) to select the desired size mode from
those indicated below.
DEFAULT, THROUGH, H-FIT, V-FIT, HV-FIT,...

60
Screen examples for different size settings (For PT-D9510U)
INPUT 
PICTURE
Default
Through
H-Fit
V-Fit
HV-Fit85
¢640·400£43
¢1152·864£54
¢1280·1024£
SIZE
SETTING
The picture is displayed at 
maximum size while maintaining 
the original aspect.
* If the picture extends outside the screen, the top-left corner is used as the reference point.