Panasonic Pt D9610U Projector User Manual

21


	



	



	



	



	



	



	



	



	



	



	



	


	



	



	



	



	



	



	



	



	



	



	



	


	



	



	



	



	



	



	



	



	



	



	



	


	...

22
Projection distance measurements for PT-D9610U(screen aspect ratio: 16:9)
unit: mm (feet/inches)
NOTE:
• The projection distance listed in the table may have a variation within ± 5 %.
• Keystone (trapezoidal distortion) is compensated to be smaller than the screen size.
Projection distance measurements for PT-D9610U (screen aspect ratio: 5:4)                   
unit: mm (feet/inches)


	



	



	



	



	



	



	



	



	...

23
Calculation of the projection distance for each projection lens (for PT-D9610U)
If there is no reference made to the require picture size, calculate the projection distance using an expression
below after obtaining the diagonal measurement (inch) of the screen you will use.
Model No. of projection lens
Aspect ratio
4:3
16:9
16:94:3
4:3
16:9 ET-D95LE5
(1.5 – 2.0 : 1)
ET-D95LE6
(2.0 – 2.5 : 1)
ET-D95LE7
(2.5 – 4.0 : 1)
ET-D95LE9
(0.8 : 1)
Z  o  o  m           l  e  n  s
Fixed
focal
lens
Methods of...

24
Adjusting projector feet
[ Side view ]
[ Front view ]
Adjustable feet
The four feet on the bottom of the projector are adjustable for the height ( 0 mm / 0 to 25 mm / 1) and can be
used for its adjustment when the installation position is not level.
Model No. of projection lens
Aspect ratio
4:3
16:9
16:9
16:94:3
4:3
4:3
16:9 ET-D95LE1
(1.5 — 2.5 : 1)
ET-D95LE2
(2.5 — 4.0 : 1)
ET-D95LE3
(4.0 — 7.0 : 1)
ET-D95LE9
(0.8: 1)Zoom lens
Fixed
focal
lens
Min.  : L = [(diagonal of screen(inches) + 12.87377) x...

25
Setting the projection method
The projection method can be set in accordance with the way the projector has been installed. If the projected
picture is upside-down or back-to-front, change the projection method while referring to illustrations A to D below.
Set  the projection method by displaying on-screen displays using the control buttons on the remote control unit or 
the projector operating panel.
Setting procedure
Press the MENU button. ... The MENU screen will be displayed.
Press the UP( ) and...

26
Adjusting the lens
Adjusting the focus
Adjustment procedure
Press the LENS button. ... The LENS screen will be displayed.
Use the control level buttons (+and −) to adjust the focus to the correct setting.
• Initial pressing of these buttons will allow fine adjustment. Pressing and holding
these buttons will allow the slow mode for the first six seconds and then the
fast mode. 
Press the MENU button. 
• The on-screen display will disappear and the screen will return to the normal
state.
Note: After the...

27
Adjustment range after lens positioning is as follows:
ÞThe numbers in brackets are the dimensions when the ET-D95LE9 lens is being used.
Adjustment range after lens position (optical shift)
(0.24H)
0.35H(0.24H)
0.35H
(0.38V)
0.5V
(0.38V)
0.5V
(0.24H)
0.35H(0.24H)
0.35H
(0.38V)
0.50V
0.31V
(0.38V)
(0.24H)
0.29H
0.31H 0.31H
0.50V
0.50V0.28V
0.22H
(0.24H)
0.29H
(0.31V)
0.38V (0.38V)
0.50V
0.31H0.31H
0.50V
0.22H
0.28V 0.50V
Standard
projection
position
Projected
screen height,V
Projected screen...

28
Obtain the required input modules (sold separately) beforehand in accordance with the system input signal.
• Types of input module (sold separately)
• Input slot numbers
• The signal sources connected to the input modules can each be selected by specifying the respective
slot number using the input select buttons on the remote control unit or the projector operating panel.
For details on selecting the input source refer to page 40.
• Modules other than the optional specified ones cannot be inserted...

29
Disconnect the power supply from the projector before installing any of the input modules.
Installation procedure
Remove the two screws which are holding the slot cover where the input module is to be installed, and then
remove the slot cover.
Fit the input module into the slot rails, and then push the input module in until it is seated in the connector, while
being careful not to bump any of the module components.
Tighten the two screws to secure module in place.
Remove the slot cover
Slot...

30
Connecting the input module signal source
When setting up the projector, you will need to connect the signal source to an input module according to the type
of signal being input.
RGB signal input module
 ET-MD95RGB
VGA to BNC
adapter cable
RGB signal
Component 
signal
Video signal input module
 ET-MD95VM2
Serial digital input module

ET-MD95SD1
TMDS input module
ET-MD95T Component 
signal
SD signal
TMDS signalProjector
Personal computer High-definition VCR
DVD player
VCR (with built-in TBC)
Multi...