Samsung Le 26r51b Owners Instructions

							English-49
Coarse and Fine Tuning of the Image
The purpose of picture quality adjustment is to remove or reduce
picture noise. If the noise is not removed by Fine-tuning alone, then
adjust the frequency as best as possible (coarse) and Fine-tune again.\
After the noise has been reduced, re-adjust the picture so that it is
aligned on the center of screen.
Press the PCbutton on the remote control to select the PC mode.
1Press the MENUbutton.
Result
: The main menu is displayed.
2Press the or  button to select Setup.
Press the 
ENTERbutton.
Result
: The options available in the Setupgroup are displayed.
3Press the or  button to select PC.
Press the ENTERbutton.
Result
: The options available in thePCmenu are displayed.
4Press the ENTERbutton again.
Result
: The Image Lockmenu is selected.
5Press the or  button to select Coarseor Fine.
Press the ENTERbutton.
Result
: The horizontal bar is displayed.
6Press the or button to adjust the screen quality. 
Press the 
ENTERbutton.
V ertical stripes may appear or the picture may become blurry.
7When you are satisfied with the settings, press the MENUbutton
to return to the previous menu or press the EXITbutton to return to
normal viewing.
BN68-00801C-02Eng.qxd  2/25/05 9:54 AM  Page 49
 
						

							English-50
Changing the Image Position
Press the PCbutton on the remote control to select the PC mode.
1Press the MENUbutton.
Result
: The main menu is displayed.
2Press the or  button to select Setup.
Press the ENTERbutton.
Result
: The options available in the Setupgroup are displayed.
3Press the or  button to select PC.
Press the ENTERbutton.
Result
: The options available in thePCmenu are displayed.
4Press the or  button to select Position.Press the ENTERbutton.
Result
:Y ou can adjust the image Position. 
5Press the  or  button to adjust horizontal position.
Press the or  button to adjust vertical position.
Press the 
ENTERbutton.
6Press the MENUbutton to return to the previous menu or press
the EXITbutton to return to normal viewing.
BN68-00801C-02Eng.qxd  2/25/05 9:54 AM  Page 50
 
						

							English-51
Initializing the Image Settings
You can replace all image settings with the factory default values.
Press the PCbutton on the remote control to select the PC mode.
1Press the MENUbutton.
Result
: The main menu is displayed.
2Press the or  button to select Setup.
Press the ENTERbutton.
Result
: The options available in the Setupgroup are displayed.
3Press the or  button to select PC.
Press the ENTERbutton.
Result
: The options available in thePCmenu are displayed.
4Press the or  button to select Image Reset. 
Press the ENTERbutton.
Result
:  You can initialize all image setting to the factory default values.
5Press the MENUbutton to return to the previous menu or press
the EXITbutton to return to normal viewing.
BN68-00801C-02Eng.qxd  2/25/05 9:54 AM  Page 51
 
						

							English-52
Teletext Decoder
Most set channels carry “ teletext ”, pages of written information\
 that
provide information such as:
Television programme times.
News bulletins and Weather forecasts.
Sports results.
Subtitles for the hard of hearing.
The teletext pages are organized according to six categories:
Part Contents
A Selected page number.
B Broadcasting station identity.
C Current page number or search status.
DD ate and time.
ET ext.
F Status information.
Displaying the Teletext Information
You can display teletext information at any time, but signal reception
must be good. Otherwise:
Information may be missing.
Some pages may not be displayed.
To  activate the teletext mode and display the contents page:
1Using the ()or ()button, select the channel providing the
teletext service.
2Press the TTX/MIX( /)button to activate the teletext mode.
Result
: The contents page is displayed. It can be redisplayed at
any time by pressing theMENU()button.
3Press the TTX/MIX( /)button again.
Result
: The screen will split into two. This Double Teletext feature
lets you view the actual broadcast and teletext
information separately on the screen.
4Press the TTX/MIX( /)button again.
Result
: The actual broadcast  will be displayed simultaneously
with the teletext page on the screen.
5To  return to normal viewing, press the PIP()button.
6Press the TV()button again to exit from the Text display. 
If any broken character appears while Text is being viewed,
make sure that the Text language is identical with the language in the
“Setup” menu mode. If both languages are different, select the same
language with the Text language on the “Setup” menu.
BN68-00801C-02Eng.qxd  2/25/05 9:54 AM  Page 52
 
						

							Press the number buttons on the remote control to enter the page
number directly:
1Enter the three-digit page number listed in the contents by pressing the\
corresponding numeric buttons.
Result
:The current page counter is incremented and the page is
then displayed.
2If the selected page is linked with several secondary pages, the
secondary pages are displayed in sequence. To freeze the display on
a given page, press the 
PRE-CH().
Press the PRE-CH ()button again to resume.
3Using the various display options:
To  display... Press the...
Both teletext information andTTX/MIX(
/)the normal broadcast
Hidden textINFO()(answers to quiz games, for example)
The normal screen 
INFO()again
A
secondary page,SLEEP()by entering its 4-digit number
The next pagePage Up(
)
)
The previous pagePage Down(
()
Double-size letters in the:SIZE()•
Upper half of the screen •Once
• Lower half of the screen •Twice
Normal screen •Three times
English-53
Selecting a Specific Teletext Page
BN68-00801C-02Eng.qxd  2/25/05 9:54 AM  Page 53
 
						

							English-54
Using Fastext to Select a Teletext Page
The various topics included in the teletext pages are colour-coded, and
can be selected by pressing the coloured buttons on the remote control.
1Display the teletext contents page by pressing the TTX/MIX(/) button.
2Press the coloured button corresponding to the topic that you wish to
select (The available topics are listed on the status information line)\
.
Result:
The page is displayed with additional colour-coded
information that can be selected in the same way.
3To display the: Press the:
Previous page Red button.
Next page Green button.
4When you have finished, press the PIP() button to return to the
normal broadcast.
BN68-00801C-02Eng.qxd  2/25/05 9:54 AM  Page 54
 
						

							English-55
Troubleshooting: Before Contacting Ser vice Personnel
Before contacting Samsung after-sales service, perform the following sim\
ple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of your
set and contact your local dealer.
No sound or picture
Normal picture but no sound
No picture or black and white picture
Sound and picture interference
Blurred or snowy picture,
distorted sound
Remote control malfunctions
“Check signal cable.” message is displayed.
On PC mode, “Not Supported Mode.” 
message is displayed.
The image is too light or too dark.
On PC mode, horizontal bars appear to flicker,
jitter or shimmer on the image.
On PC mode, vertical bars appear to flicker,
jitter or shimmer on the image.
On PC mode, screen is black and  power 
indicator light blinks every 1 second.
On PC mode, image is not stable and 
may appear to vibrate.
On PC mode, image is not centered 
on the screen.
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the POWERbuttons on the lower-right
panel.
Check the picture contrast and brightness settings.
Check the volume.
Check the volume.
Check whether the 
MUTEbutton has been pressed on the remote
control.
Adjust the colour settings.
Check that the broadcast system selected is correct.
T ry to identify the electrical appliance that is affecting the set and move it
further away.
Plug your set into a different mains socket.
Check the direction, location and connections of your aerial.
This interference is often due to the use of an indoor aerial.
Replace the remote control batteries.
Clean the upper edge of the remote control (transmission window).
Check the battery terminals.
Check that the signal cable is firmly connected to the PC or video sourc\
es.
Check that the PC or video sources are turned on.
Check the maximum resolution and the frequency of the video adapter.
Compare these values with the data in the Display Modes. 
Adjust the Brightness and Contrast.
Adjust the Fine function.
Adjust the Coarse function and then adjust the Fine function.
The TV is using its power management system.
Move the computer’s mouse or press any key on the keyboard.
Check that the display resolution and frequency from your computer or
video board is an available mode for your set. On your computer check:
Control Panel, Display, Settings.
If the setting is not correct, use your computer utility programme to ch\
ange
the display settings. 
Your set supports multiscan display functions within the following
frequency domain:
Horizontal frequency(kHz): 30~ 61
V ertical frequency(Hz): 60~75
Maximum refresh rate (at 60Hz): 1360 X 768
Adjust the horizontal and vertical position.
The TFT LCD panel uses a panel consisting of sub pixels (3,147,264) which requ\
ire sophisticated technology to produce.
However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the
product.
BN68-00801C-02Eng.qxd  2/25/05 9:54 AM  Page 55
 
						

							English-56
Installing the Wall Mount Kit (LE26R51B)
This installation is to be used when attaching the wall mount to a concr\
ete wall.
When attaching to other building materials, please contact your nearest \
dealer.
Components (Sold separately)
M4 X L15
Wall-Bracket Set-Bracket Screw: 8EA
M4 X L20
Wood Screw: 4EA Anchor: 4EA Installation Guide
How to assemble the Wall Mount Bracket
1Mark the location of hole on the wall.
Drill a hole of 35mm depth on the marked
location.Fix anchors on each hole on the wall.
Connect wall-bracket to the wall with wood
screws after fitting anchors into the 
wall-bracket
.
Note: If the bracket is not firmly fixed to the wall,
LCD TV can fall off.
BN68-00801C-02Eng.qxd  2/25/05 9:54 AM  Page 56
 
						

							English-57
Installing the Wall Mount Kit (LE26R51B)
2  Turn the power off and unplug the power cord from the outlet.Place the TV faced down on a soft cloth or cushion on a table.
Remove the four screws from the  back of the TV.
Separate the stand from the TV.
Cover the bottom hole with a cap
Attach the set-bracket onto the rear side of the TV set and secure the screws .
3  Insert three Hangers of the set-bracket into the grooves of the wall-bracket . Fix set-bracket and wall-bracket with screws .
Note: Before installing the set on the wall, connect the cables to the s\
et first.
How to assemble the Wall Mount Bracket
BN68-00801C-02Eng.qxd  2/25/05 9:55 AM  Page 57
 
						

							English-58
Installing the Wall Mount Kit (LE32R51B, LE32R52B, LE40R51B)
This installation is to be used when attaching the wall mount to a concr\
ete wall.
When attaching to other building materials, please contact your nearest \
dealer.
Components (Sold separately)
Wall-Bracket Set-Bracket Screw: 8EA
Wood Screw: 7EA Anchor: 7EA Screw: 3EA Installation Guide
How to assemble the Wall Mount Bracket
1Mark the location of hole on the wall.
Drill a hole of 35mm depth on the marked
location.Fix anchors on each hole on the wall.
Connect wall-bracket to the wall with wood
screws after fitting anchors into the 
wall-bracket
.
Note: If the bracket is not firmly fixed to the wall,
LCD TV can fall off.
M6 X L14
M4 X L25 M4 X L8
BN68-00801C-02Eng.qxd  2/25/05 9:55 AM  Page 58