Toshiba Strata Se, Strata Vie General Description Manual

Note: 
If the system is to have the Off-hook Call An- 
nounce feature, leave 00 blank for voice an- 
nounce. 
O#l Program- Door Phone Selection 
Ten options are selected with this program 
using the various keys to change the status of 
their respective LEDs. For the options selected, 
mark an X as indicated. 
1) Door Lock Timeout-mark an X next to 17 if 
the door lock is to operate for 6 seconds. 
Leave blank if 3 seconds are sufficient. 
Door Phone 12/14B Door Lock-mark an X 
next to 08 if door phone...

PROGRAMMING PROCEDURES 
SECTION’ 500-036-300 
JANUARY 1988 
0#2 Program-Account Code Digit Length Se- 
lection 
This program has two sections. The first de- 
fines the number of digits required in an ac- 
count code (Forced Account Code feature). Enter 
the number of digits to be used (4 - 15). The 
second section sets SDTU modem speed and re- 
peat ringing. 
1) Repeat Ringing- mark an X next to 17 if re- 
peat ringing is required. Leave blank if stand- 
ard ringing is required. 
2) Modem Speed-mark an X...

NOTE: 
[f AROH is available, the CO will automati- 
cally drop the lines when the outside party 
hangs up. However, if AROH is not available, 
the person who sets up the Trunk-to-Trunk 
Connection must occasionally monitor the 
call and disconnect the CO lines when the 
two parties hang up. 
0#6 Program-Trunk-to-Trunk Connection 
Enable 
Selects the CO lines to be used for trunk- 
to-trunk connections. 
l Mark an X next to CO lines to be used for 
trunk-to-trunk connections. 
07 Program-Automatic Release...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
NOTE. 
If the access code is a single digit, enter ‘I*” 
in the second column. If all combinations fol- 
lowing a particular first digit are to be con- 
sidered access codes (e.g., 9 1, 92, 93, etc.), 
enter ‘D” (D = key 18 on station 13/17) in 
the second column. 
03.30 Toll Restriction Assignments 
100 Program-Toll Restriction System Pa- 
rameters 
An entry in this program is required only if 
3- or 6-digit toll restriction is desired. Informs...

, 2. Enter the number of digits in the OCC Au- 
thorization Code (00 - 99). 
3. Caution: Do not program more digits than 
required because toll restriction may be 
defeated. 
108 Program-Toll Restriction Override Code 
#l 
Registers the first of two codes that over- 
ride toll restriction on outgoing calls. 
l Enter the four digits of the first toll restric- 
tion override code. 
109 Program-Toll Restriction Override Code 
#2 
Registers the second of two codes that over- 
ride toll restriction on...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1966 
l Program 2XY (211 and 212) are pro- 
grammed for area code 213 (212) and of- 
fice code 635 also 
(211). Class 1 stations 
are allowed to dial all office codes in area 
code 213 
except 635. 
1 Xl Program- Toll Restriction Class Area/ 
Office Code Exception Table Selection (X = 
Class 1 - 4) 
Entry to this program is required only if 
&digit (area/office code) toll restriction is de- 
sired. There are eight. area/office code excep- 
tion tables...

Start Time “C” is the stop time for “8” 
Start Time “A” is the stop time for “C” 
2) Select the priority class required (Programs 
l#X51 - 53). Enter the route group 
numbers (1 - 4) required (refer to Program 
1#8XY). 
NOTE. 
If a table is to be used 24 hours a day, the 
Schedule B Start Time must be the same as 
Schedule A Start Time. 
l#X60 - 
63 Program- LCR Route Table, 
Start Time 6 Schedule 
This program will define the stop time for 
a previousiy selected start time and/or the start 
time for...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
7) Mark an X next to 00 if the telephone or de- 
vice connected to the HIOB is to have pri- 
vacy. Leave blank if privacy is not required. 
4XX Program- Station Type Assignment 
NOTE. 
When programming, 
always do Program 
4XX 
before Program 4#XX. lf Program 4XX 
is programmed after 4#XX, the stations’ flex- 
ible key assignments will be reset to the de- 
fault data. 
Informs the system of the EKT type being 
used at each station and the order...

IO-key 20. key 
FIGURE 3-Vie EKT KEY PAlTERNS 
Informs the system of the features that are 
assigned to the flexible keys at each station 
PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
l Any key (except INT) may be assigned a fea- 
ture code (Figure 4). All assigned feature 
codes have priority over Program 4XX as- 
signments. For each key on every station, 
write in the name or code for each feature 
to be assigned. 
NOTES. 
1. A feature (code) may be assigned to one 
key only, except for...

PROGRAMMING PROCEDURES 
SECTION 500-036-300 
JANUARY 1988 
gram, using the various keys to change the sta- 
tus of their respective LEDs. The selections 
listed below must be repeated for each station. 
In all cases, mark an X where required. 
1) Privacy Override- mark an X next to 17 if the 
station is allowed the Privacy Override fea- 
ture. Allows an override (break-in) when a 
CO key is depressed with the CO LED on 
steady. Both parties can hear an override 
tone. 
NOTE. 
A maximum of two stations...