Home > Canon > Printer > Canon Imageprograf Ipf815 Mfp M40 User Guide

Canon Imageprograf Ipf815 Mfp M40 User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Canon Imageprograf Ipf815 Mfp M40 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 960
    							1.
    Lift the Holder Stopper lever (a) from the shaft side to unlock it. Holding the Holder Stopper at the position indica-
    ted (b), remove it from the Roll Holder. 2.
    When 
    using a 3-inch paper core, align the tips (a) of 3-Inch Paper Core Attachment #1 with the holes (b) of the Roll
    Holder and insert it firmly. Handling Paper 
    > Handling rolls >
    iPF815
    Attaching the Roll Holder to Rolls 7
    625
     
    						
    							3.
    With the  edge  of  the  roll  paper  facing  forward  as  shown,  insert  the  Roll  Holder  from  the  right  of  the  roll.  Insert  it
    firmly until the roll touches the flange (a) of the Roll Holder. Important
    • When 
    loading  a  roll,  be  careful  to  avoid  hitting  the  printer  hard  with  the  roll.  This  may  damage  the
    Roll Holder.
    4. Insert the attachments for the roll paper core on the Holder Stopper.
    Align the tips (a) of the attachment with the holes (b) of the Holder Stopper and insert it firmly.
    •3-Inch Paper Core Attachment #2 Handling Paper 
    > Handling rolls >
    Attaching the Roll Holder to Rolls
    iPF8157
    626
     
    						
    							•
    2-Inch Paper Core Attachment 5.
    Insert the  Holder  Stopper  from  the  left  in  the  Roll  Holder  as  shown.  Holding  it  at  the  position  shown  (b),  push  it
    firmly in until the flange (a) of the Holder Stopper touches the roll. Lock the Holder Stopper lever (c) by pushing it
    down toward the shaft side. Handling Paper 
    > Handling rolls >
    iPF815
    Attaching the Roll Holder to Rolls 7
    627
     
    						
    							Loading Rolls in the Printer
    Follow these steps to load rolls in the printer. Note
    • Remove any loaded paper that will not be used.
    • Rolls  (See "Removing the Roll from the Printer .") →P.634
    • Sheet  (See "Removing Sheets .") →P.656
    • If the Platen is dirty, clean inside the Top Cover.   (See "Cleaning Inside the Top Cover.") →P.837
    • After 
    pressing  the  Load/Eject  button,  you  can  refer  to  instructions  on  the  Display  Screen  as  you  load  the
    paper.  (See "Checking Instructions During Printer Operations .") →P.743
    1. Confirm that a roll is selected as the paper source.   (See "Selecting the Paper Source.") →P.631
    2.
    Open the Top Cover and lift the Ejection Guide. Handling Paper 
    > Handling rolls >
    Loading Rolls in the Printer
    iPF8157
    628
     
    						
    							3.
    Holding  the Roll Holder so that the side with the white gear faces the side of the Roll Holder Slot with a white gear,
    load the Roll Holder shaft (a) into the grooves (b) on both ends of the Roll Holder Slot. Caution
    • Be 
    careful not to pinch your fingers between the Roll Holder shaft (a) and the guide grooves (b) when
    loading rolls. Note
    • For 
    instructions  on  attaching  the  Roll  Holder  to  rolls,  see  "Attaching  the  Roll  Holder  to  Rolls."→P.623 Handling Paper 
    > Handling rolls >
    iPF815
    Loading Rolls in the Printer 7
    629
     
    						
    							4.
    Pull out  the  roll  paper  evenly  on  both  ends.  Using  both  hands,  insert  the  roll  paper  in  the  Paper  Feed  Slot  and  ad-
    vance it until the buzzer sounds. Important
    • Be 
    careful not to soil the printing surface of roll paper as you insert it in the slot. This may affect the
    printing  quality.  We  recommend  wearing  clean  cloth  gloves  when  handling  rolls  to  protect  the  print-ing surface.
    • If the paper is wrinkled or warped, straighten it out before loading it.
    • Load the roll so that there is no gap between the right edge of the paper and the Roll Holder. Handling Paper 
    > Handling rolls >
    Loading Rolls in the Printer
    iPF8157
    630
     
    						
    							5.
    Lower the Ejection Guide. 6.
    Close the Top Cover. 7.
    Press the OK button.
    The printer will now advance the paper.
    After you load a roll, the printer automatically shows a menu for selection of the type of paper on the Display Screen.
    At this point, specify the type of paper.   (See "Selecting the Paper Type (Roll) .") →P.632
    Selecting the Paper Source
    When advancing paper, press the  Feeder Selection button and select the source.
    You can determine the selected source by checking which lamp is lit—either the  Roll Media lamp (a) or the Cut Sheet
    lamp (b).
    •
    Roll Media lamp : Selected when printing on Roll Media.
    • Cut Sheet lamp  : Selected when printing on Sheets. Handling Paper 
    > Handling rolls >
    iPF815
    Selecting the Paper Source 7
    631
     
    						
    							Note
    • If a  sheet  is  loaded  when  you  change  the  paper  source  to  a  roll,  " Eject  sheet?"  is  displayed.  Press  the  OK
    button and remove the sheet.
    • You cannot switch the paper source in the following situations:
    • When the Message lamp is flashing
    Check  the  message  on  the  Display  Screen  and  take  action  as  necessary.  (See  " Error  Messag-
    es →P.891
    .")
    • When the Data lamp is flashing
    Select the paper source after printing is finished.
    • When a printer menu operation is in progress
    Wait until the operation is finished before selecting the paper source.
    • When in the process of loading paper
    Finish loading the paper before selecting the paper source.
    • When in the process of replacing Ink Tank
    Finish replacing the Ink Tank before selecting the paper source.
    • When the Top Cover is open
    Close the Top Cover before selecting the paper source. Selecting the Paper Type (Roll)
    When changing the type of paper after the paper has been advanced, specify the type of paper as follows. Important
    • For 
    best  printing  results,  the  printer  fine-tunes  the  feed  amount  for  each  type  of  paper.  Be  sure  to  select  the
    type of paper to use correctly before printing.
    • Because  the  printer  fine-tunes  the  feed  amount  for  each  type  of  paper,  the  margins  and  the  size  of  printed
    images  may  vary  depending  on  the  type  of  paper  used.  If  margins  and  the  size  of  images  are  not  as  you  ex- pected, adjust the paper feed amount and Printhead height.
     (See "Adjusting the Feed Amount .") →P.676
     (See " Troubleshooting Paper Abrasion and Blurry Images (Head Height) .") →P.675
    Note
    • After 
    you load the roll, the printer automatically shows a menu for selection of the paper type on the Display
    Screen,  unless  a  barcode  has  been  printed  on  the  roll  or  you  have  activated  automatic  monitoring  of  the  re-
    maining roll paper. Select the type of paper, and then press the  OK button.
    If no barcode has been printed on the roll and you have activated automatic monitoring of the remaining roll
    paper, specify the roll length after the paper type.   (See "Specifying the Paper Length (Roll).") →P.633
    1. Press the Menu button to display  MAIN MENU.Handling Paper 
    > Handling rolls >
    Selecting the Paper Type (Roll)
    iPF8157
    632
     
    						
    							2.
    Press ▲ or ▼ to select  Media Menu, and then press the  ▶ button.
    3. Press ▲ or ▼ to select  Roll Media Type, and then press the  ▶ button.
    4. Press ▲ or ▼ to select the type of paper loaded in the printer, and then press the  OK button.Note
    • For details on types of paper, see the Paper Reference Guide.   (See "Types of Paper.") →P.617
     By
    default, Plain Paper is selected.
    • If you move the Release Lever, the setting automatically reverts to the previously selected paper.
    • Be 
    sure to select the correct paper type. If this setting does not match the loaded paper, it may cause
    feed errors and affect printing quality.
    • If automatic monitoring of the remaining roll is deactivated (  Off is selected) and you have selected a
    type of paper for which width detection is deactivated (  Off is selected), you must advance the paper
    manually to the position for printing.   (See "Manually Loading Paper to the Position for Printing .")→P.654
    5. Press the Online  button to bring the printer online.Specifying the Paper Length (Roll)
    When changing the length of paper after the paper has been advanced, specify the length as follows. Note
    • When you specify the roll length in the printer menu,  ManageRemainRoll must be set to On.
    • After 
    
    you select the type of roll, the printer automatically shows a menu for selection of the roll length on the
    Display  Screen  if  no  barcode  has  been  printed  on  the  roll  and  you  have  set  ManageRemainRoll  to On.  Se-
    lect the roll length, and then press the  OK button. The printer will automatically go online.
    1. Press the Menu button to display  MAIN MENU. Handling Paper 
    > Handling rolls >
    iPF815
    Specifying the Paper Length (Roll) 7
    633
     
    						
    							2.
    Press ▲ or ▼ to select  Media Menu, and then press the  ▶ button.
    3. Press ▲ or ▼ to select  Roll Length Set, and then press the  ▶ button.
    4. Press  ▲ or ▼ to select the length of paper loaded in the printer, and then press the  OK button.
    Specify the roll length as follows.
    1. Press  ◀ or ▶ to move the cursor (_) to each field for entering numbers.
    2. Press the ▲  or ▼ button to enter the value.
    3. Repeat steps 1 and 2 to finish entering the value, and then press the  OK button.
    5. Press the Online  button to bring the printer online.Removing the Roll from the Printer
    Remove rolls from the printer as follows. Note
    • If you  need  to  cut  a  printed  roll,  select  Paper  Cutting  in  the  printer  menu  and  cut  the  roll  at  the  desired
    position.   (See "Specifying the Cutting Method for Rolls .") →P.642
    • If 
    
    you have selected  Media Menu >ManageRemainRoll  >On in the printer menu, a barcode indicating the
    amount  of  paper  left  is  printed  on  the  leading  edge  of  the  roll.  However,  barcodes  are  not  printed  on  some
    types of paper, and only a text message indicating paper information is printed. Caution
    • If 
    you  have  activated  automatic  monitoring  of  the  remaining  roll  paper,  do  not  remove  the  roll  before  the
    barcode is printed. You will be unable to keep track of the amount of roll paper left.
    Handling Paper 
    > Handling rolls >
    Removing the Roll from the Printer
    iPF8157
    634
     
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon Imageprograf Ipf815 Mfp M40 User Guide