Home > Canon > Printer > Canon Imageprograf Ipf815 Mfp M40 User Guide

Canon Imageprograf Ipf815 Mfp M40 User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Canon Imageprograf Ipf815 Mfp M40 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 960
    							2.
    Keeping  the right edge of the paper aligned with the extended line of the Paper Alignment Line (a) on the right side
    of the printer, load the paper so that the near edge is aligned with the groove (b) at the far end of the Platen.
    In  this  case,  advance  the  paper  as  far  into  the  paper  feed  slot  as  possible  because  it  will  be  printed  starting  at  that
    position. 3.
    Lower the Release Lever and close the Top Cover.
    4. If 
    
    no  print  job  has  been  received  from  the  computer,  press  ▲  or ▼  to  select  of  the  type  of  paper  loaded,  and  then
    press the OK button.
    5. When "Width Detection OFF. OK to continue?" is shown on the Display Screen, press  ▲ or  ▼ to select " Leave
    OFF " and then press the OK button. 6.
    Check the position of the loaded paper and press the  OK button.
    7. Press  ▲ or ▼ to select the paper size, and then press the  OK button. Handling Paper 
    > Handling sheets >
    iPF815
    Manually Loading Paper to the Position for Printing 7
    655
     
    						
    							Note
    • If a print job received requires paper larger than the selected paper, it may soil the Platen. Removing Sheets
    Remove sheets from the printer as follows.
    1. Press the Load/Eject button. Note
    • Paper cannot be ejected by using the  Load/Eject button when print jobs are in progress or during the
    ink  drying  period.  Before  ejecting  paper,  press  the  Stop  button  to  cancel  printing,  print  job  process-
    ing, or ink drying.
    2. Press the OK  button to eject the paper. The paper is ejected from the front of the printer.
    Handling Paper 
    > Handling sheets >
    Removing Sheets
    iPF8157
    656
     
    						
    							3.
    As you hold the sheet, lift the Release Lever and remove the sheet. 4.
    Lower the Release Lever. Handling Paper > Handling sheets >
    iPF815
    Removing Sheets 7
    657
     
    						
    							Output Stacker
    Stationary Output Stacker ............................................................................................................................... 658
    Using the Stationary Output Stacker ............................................................................................................... 659
    Stowing the Stationary Output Stacker ........................................................................................................... 661
     
    Wheeled Output Stacker ................................................................................................................................. 663
    Using the Wheeled Output Stacker ............................................................................................................. 663Stationary Output Stacker
    a.
    Output Stacker
    A cloth tray that catches ejected documents. b.
    White tag
    A point of reference for attaching the Output Stacker in the right direction.
    c.
    Basket Arm R and Basket Arm L
    Holds the Basket Rod (tag side) attached to the Output Stacker. When the Output Stacker is not used, push it down and
    store it next to the Stand Leg. d.
    Basket Rod (tag side) and Basket Rod (cord side)
    Holds the cloth Output Stacker securely in specific positions.
    Handling Paper > Output Stacker >
    Stationary Output Stacker
    iPF8157
    658
     
    						
    							e.
    Basket Rod
    Keeps Basket Arm R and Basket Arm L at the same angle.
    f.
    Rear Holder
    Holds the middle of the Basket Rod (cord side).
     (See "Using the Stationary Output Stacker .") →P.659
    Note
    • The printer can be used with either a Stationary Output Stacker or a separate, mobile Wheeled Output Stack-
    er.
    The Stationary Output Stacker is normally provided as the standard stacker, but the Wheeled Output Stackermay  be  the  standard  stacker  in  some  sales  regions.  If  the  Wheeled  Output  Stacker  has  been  provided  as  the
    standard stacker, the Stationary Output Stacker is not included.
    For more information about the Wheeled Output Stacker,  see "Wheeled Output Stacker." →P.663
    Using the Stationary Output Stacker
    The Stationary Output Stacker can be used in three positions, as shown.
    •
    When storing printed documents on the Output Stacker
    Use position (1).
    •
    When the Output Stacker is not used
    Move the stacker into position (2). Handling Paper 
    > Output Stacker >
    iPF815
    Using the Stationary Output Stacker 7
    659
     
    						
    							•
    When the Media Take-up Unit is used, or when the Output Stacker is stored for long periods
    Lower it to position (3) for storage. 
     (See "Stowing the Stationary Output Stacker.") →P.661
    When 
    using  the  Output  Stacker  again  after  storage,  reattach  the  Basket  Rod  on  the  front  of  the  Output  Stacker  to  the
    tips of the left and right basket arms and pull the side rods out completely. •
    When printing on large, stiff sheets
    Use position (3). Important
    • When 
    storing  printed  documents  on  the  Output  Stacker,  always  use  it  in  position  (1).  If  you  do  not,  printed
    documents may not be dropped into the Output Stacker, and the printed surface may become soiled.
    • The Output Stacker can accommodate one sheet. When printing multiple pages, remove each sheet after it is
    printed.
    • Before using the Output Stacker, remove the Rewind Spool. If you do not, it may prevent printed documents
    from being held correctly, and they may be scratched.
    • The  Output  Stacker  can  hold  printed  documents  from  rolls  that  are  62  inches  (1,575  mm)  long.  When  print-
    ing longer documents, use the optional Media Take-up Unit.
    The Output Stacker locks into position if you lift it to position (1) or (2). To lower the Output Stacker, lift the front Basket
    Rod lightly to release the lock, and then lower the stacker. Handling Paper 
    > Output Stacker >
    Using the Stationary Output Stacker
    iPF8157
    660
     
    						
    							Stowing the Stationary Output Stacker
    Stow the Stationary Output Stacker if you will use the Media Take-up Unit or if you will not use the Stationary Output
    Stacker for an extended period.
    1. When 
    the Output Stacker is in the position used when storing printed documents (a), lift the front Basket Rod gently
    to release the lock, lower the stacker toward the front (b), and push it all the way back. 2.
    Remove 
     the front Basket Rod from the left and right Basket Arms. Roll up the Basket Cloth and put it at the back of
    the Bottom Stand Stay. Handling Paper 
    > Output Stacker >
    iPF815
    Stowing the Stationary Output Stacker 7
    661
     
    						
    							Important
    • When using  the  optional  Media  Take-up  Unit,  position  the  Basket  Cloth  and  Basket  Rod  so  they  do
    not interfere with the Media Take-up Sensor (indicated by the dashed line). 3.
    Push in the left and right Basket Arm toward the back all the way, until they stop. Handling Paper 
    > Output Stacker >
    Stowing the Stationary Output Stacker
    iPF8157
    662
     
    						
    							Wheeled Output Stacker
    An output stacker with casters, positioned in front of the printer. a.
    Output Stacker
    A cloth tray that catches ejected documents.
    The Output Stacker can be opened and closed using the rod in front. b.
    Output Stacker Ejection Guides
    Prevent printed documents from winding around the Roll Holder or being drawn into the Paper Feed Slot.
    Hold the Wheeled Output Stacker by these guides when moving it. c.
    Output Stacker Foot Stand
    Equipped with casters to facilitate moving it.
    d.
    Stopper
    Locks the Stand casters.
    Always 
    release the Stopper before moving the printer. Moving the printer while the Stopper is locked may scratch the
    casters or the floor. Note
    • For 
    instructions  on  assembling  the  Wheeled  Output  Stacker,  see  the  setup  guide  provided  with  the  Wheeled
    Output Stacker.
    • The printer can be used with either a Stationary Output Stacker or a separate, mobile Wheeled Output Stack-
    er.
    The Wheeled Output Stacker is normally provided as an optional accessory, but it may be the standard stack-
    er  in  some  sales  regions.  If  the  Wheeled  Output  Stacker  has  been  provided  as  the  standard  stacker,  the  Sta- tionary Output Stacker is not included.
    For more information about the Stationary Output Stacker,  see "Stationary Output Stacker." →P.658
    Using the Wheeled Output Stacker
    Positioning the Wheeled Output Stacker by the printer will prevent rolls from dropping on the floor after printing.
    The stacker is equipped with casters to facilitate moving it. Important
    • The 
    Output Stacker can accommodate one sheet. When printing multiple pages, remove each sheet after it is
    printed. Handling Paper 
    > Output Stacker >
    iPF815
    Wheeled Output Stacker 7
    663
     
    						
    							Positioning the Wheeled Output Stacker by the printer
    1. Holding the Output Stacker Ejection Guides (a), move the stacker between the printer Stand. 2.
    Lock the casters. Handling Paper > Output Stacker >
    Using the Wheeled Output Stacker
    iPF8157
    664
     
    						
    All Canon manuals Comments (0)

    Related Manuals for Canon Imageprograf Ipf815 Mfp M40 User Guide