Canon Imageprograf Ipf815 Mfp M40 User Guide

							Item
DetailsDefault
Setting
NDS PSer-
ver Tree Name
Specify the name of an NDS tree that has a NetWare print server.
(0–32 characters) —
Context Name Specify the name of a context that has a NetWare print server.
(0–255 characters) —
Print Server
Name Specify the name of a NetWare print server.
(0–64 characters) —
Print Server
Password Set a password for the print server.
(0–20 characters) —
Polling Interval Specify the interval to confirm jobs.
(1–255 seconds) 5
NPrinter Print Server Name Specify the name of a NetWare print server.
(0–47 characters) —
Printer Number Specify the number of the printer connected to the NetWare print
server.
(0–254) 07.
Click  OK to display the  Network page.Specifying the Printer's Frame Type
To enable communication between the printer and computers on your network, specify the Ethernet frame type in your Net-
Ware environment.
Follow the steps below to specify the frame type by using imagePROGRAF Device Setup Utility or the printer Control
Panel. Note
• You can specify the frame type by using RemoteUI if the printer's IP address is configured. Important
• Before specifying the frame type, make sure the printer is on and connected to the network.
• For 
instructions  on  installing  imagePROGRAF  Device  Setup  Utility,  see  "Installing  imagePROGRAF  De-
vice Setup Utility." →P.403
. Specifying the Frame Type Using imagePROGRAF Device Setup Utility
1. Start imagePROGRAF Device Setup Utility.
2. In the list of printers, select the printer to configure.
3. Choose Protocol Settings  from the Printer menu.
4. In the  NetWare Frame Type list, select the frame type.
5. Click  ETHERNET II  under Frame Type  in TCP/IP. Network Setting 
> Network Setting (Windows) >
iPF815
Specifying the Printer's Frame Type 10
785
 
						

							6.
In IP Address ,  enter the IP address assigned to the printer, and then enter the subnet mask in  Subnet Mask and the
default gateway in  Gateway Address. Important
• You 
must specify the IP address here to be able to configure NetWare protocol settings using Remo-
teUI.
7. Click  Set.
8. Click  OK after the  Confirmation message dialog box is displayed.
9. Exit imagePROGRAF Device Setup Utility. Specifying the Frame Type Using the Printer Control Panel
1. Press the Menu button to display  MAIN MENU.2.
Press â–² or â–¼  to select Interface
  Setup, and then press the  â–¶ button.
3. Press  â–² or â–¼ to select  NetWare, and then press the â–¶ button.
4. Press â–² or â–¼  to select NetWare , and then press the â–¶ button.
5. Press â–² or â–¼ to select  On, and then press the OK button.
Return to the  NetWare menu.
6. Press â–² or â–¼ to select  Frame Type, and then press the  â–¶ button.
7. Press â–² or â–¼ to select the frame type to use, and then press the  OK button.
Return to the  NetWare menu.
8. Press  â–² or â–¼ to select  Print Service, and then press the â–¶ button.
9. Press  â–² or â–¼ to select the desired print service, and then press the  OK button.
Return to the  NetWare menu.
Network Setting 
> Network Setting (Windows) >
Specifying the Printer's Frame Type
iPF81510
786
 
						

							10.
Press the Online  button to bring the printer online.
If any of the settings is changed, a message for confirmation is displayed. In this case, press the  OK button.Important
• Be sure to complete step 10. This will activate the values you have entered. Note
• If an error message is displayed, check the settings and correct any invalid values.
• To cancel the setup process, hold down the  Stop button for a second or more. Specifying NetWare Print Services
Before printing in a NetWare network, you must configure print services such as print servers, print queues, and so on. You
can configure the print service settings from a computer using any of the following software.
•NWADMIN
• PCONSOLE
(from Novell, provided with NetWare) Important
• If you use NWADMIN to configure the print service settings, Novell Client (the Novell NetWare client soft-
ware) must be installed as the client software application.
• NetWare networking is unsupported in Windows Vista.
This topic gives instructions for configuring NetWare print services. The order of this procedure may vary depending on the
environment. Choosing the type of print services
Before completing print service settings, choose the type of print service. Refer to the following descriptions as needed. Note
• In 
NetWare 5.1 or 6.0, NDPS may also be used as the print service. If you use NDPS, use the Novell printer
gateway included with NetWare. For details on configuring NDPS, refer to the NetWare documentation.
• NDS (Novell Directory Service) and bindery
NDS and bindery are both supported. Use the mode that is compatible with your network environment.
• Queue server mode and remote printer mode
Queue server mode and remote printer mode are both supported.
•Queue server mode Network Setting 
> Network Setting (Windows) >
iPF815
Specifying NetWare Print Services 10
787
 
						

							When using queue server mode, all print server functions are supported, so there is no need for other print server
software  or  hardware.  In  NDS  queue  server  mode  (NDS  PServer),  the  NDS  print  server  is  used  for  printing.  In
bindery  queue  server  mode  (Bindery  PServer),  the  bindery  print  server  is  used  for  printing.  Note  that  if  you  use queue server mode, a NetWare user license is required for each network interface.
• Remote printer mode
In remote printer mode, the printer is controlled by the NetWare print server. Thus, a NetWare print server is re-
quired.  In  NDS  remote  printer  mode  (NPrinter),  the  NDS  print  server  is  used  for  printing,  and  in  bindery  remote
printer mode (RPrinter), the bindery print server is used for printing. Using NWADMIN or PCONSOLE to set up the print server
Use NWADMIN to set up the print server if NDS queue server mode or remote printer mode is used.
1. Log into NetWare as Administrator or with equivalent rights, and then start NWADMIN.
2. Run Quick Setup.
1. Choose Print Services Quick Setup  in the Tools menu.
2. Enter 

a  desired  name  in  Print  Server  Name .  To  use  an  existing  print  server,  click  the  button  at  right  and
choose the name from the list.
3. Enter a desired printer name in  Name.
4. To use the printer in queue server mode, choose  Other/Unknown in Type. To use the printer in remote printer
mode,  choose  Parallel  in Type,  click  Communications,  and  set  Ports  to LPT1  and Connection  Type  to
Manual Load.
5. Enter a desired queue name in  Name.
6. In Volume, enter the volume object (that is, the object representing the physical volume on the network) where
the print queue will be created. Click the button at right to choose from a list.
7. Complete other settings as needed and click  OK.Note
• The 
print  server  name  will  be  required  when  configuring  the  printer's  protocol  settings.  Write  down
the print server name for future reference.
• When running Quick Setup, the printer is assigned printer number 0. When using the printer in queue
server mode, do not change the printer number from 0.
3. Set a password.
1. Right-click the print server created in step 2 and choose  Details.
2. Click Change Password to open the password input dialog box. Enter the password.
3. Click  OK to close the password input dialog box.
4. Click  OK or Cancel to close the details dialog box.
Network Setting 
> Network Setting (Windows) >
Specifying NetWare Print Services
iPF81510
788
 
						

							4.
To use the printer in remote printer mode, start the print server.
To  use  the  NetWare  file  server  as  the  print  server,  enter  LOAD  PSERVER.NLM  at  the  file  server  and  press  the
Enter key. Note
• This procedure is not required when using queue server mode.
Use PCONSOLE to set up the print server if bindery queue server mode or remote printer mode is used. 1. Log into NetWare as Supervisor and start PCONSOLE.
2. Switch to bindery mode.
3. If the print server has not been created, create it.
1. In Available Options, select Quick Setup and press the Enter key.
2. Enter the name of the new print server, the new printer, and the queue. Note
• The 
print  server  name  will  be  required  when  configuring  the  printer's  protocol  settings.  Write  down
the print server name for future reference.
4. Specify the printer type.
1. To 

use  the  printer  in  queue  server  mode,  choose  Other/Unknown  in Type.  To  use  remote  printer  mode,  set
Printer Type  to Parallel and Position to  Manual Load.
2. Press the Esc key.
3. After the confirmation message is displayed, choose  Yes and press the Enter key.
5. Set a password.
1. In Available Options, select  Print Servers and press the Enter key.
2. Select the print server created in step 2 and press the Enter key.
3. Select  Password , and press the Enter key to display the password input dialog box.
4. Enter the password and press the Enter key.
6. Press the Esc key several times to display the dialog box for confirming that PCONSOLE is finished.
7. Click Yes to exit PCONSOLE. Specifying NetWare Protocols
Follow the steps below to configure NetWare protocol settings other than the frame type by using RemoteUI. Note
• For details on RemoteUI,  see "Using RemoteUI." →P.776Network Setting 
> Network Setting (Windows) >
iPF815
Specifying NetWare Protocols 10
789
 
						

							1.
Start the  web  browser  and  enter  the  following  URL  in  the  Location  (or Address   )  box  to  display  the  RemoteUI
page.
http://printer IP address or name/
Example: http://xxx.xxx.xxx.xxx/
2. Select  Administrator Mode and click  Logon.
3. If a password has been set on the printer, enter the password.
4. Click  Network  in the Device Manager  menu at left to display the  Network page.
5. Click  Edit in the upper-right corner of the  NetWare group to display the Edit NetWare Protocol Settings  page.
6. Make sure the Frame Type indicates the frame type used on the NetWare network.
7. To use burst mode, choose  On for NCP Burst Mode. Note
• Burst mode supports fast data transfer when printing in queue server mode. Normally, choose  On.
8. In Print Application , click the print service to be used. Note
• Only 
one  print  service  selected  here  will  be  enabled.  Multiple  print  services  are  not  available  at  the
same time.
9. For packet signature, click  If Requested by Server in Packet Signature.
10. Complete the following settings based on the selected service.
•If you have selected Bindery PServer: Queue Server Mode (Using a Bindery Print Server)
1. In File Server Name , enter the file server name.
2. In Print 

Server  Name,  enter  the  name  of  the  print  server  created  in  " Specifying  NetWare  Print  Serv-
ices →P.787
."
3. In Print 

Server  Password,  enter  the  password  of  the  print  server  created  in  " Specifying  NetWare  Print
Services →P.787
."
4. In Polling Interval , specify the interval at which the printer checks the NetWare print queue.
• If you have selected RPrinter: Remote Printer Mode (Using a Bindery Print Server)
1. In Print 

Server  Name ,  enter  the  advertising  name  of  the  print  server  created  in  " Specifying  NetWare
Print Services →P.787
."
2. In Printer 

Number,  enter  the  same  printer  number  specified  in  "Specifying  NetWare  Print  Serv-
ices →P.787
."
• If you have selected NDS PServer: Queue Server Mode (Using an NDS Print Server)
1. In Tree Name  and Context Name, enter the tree and context name of the print server.
Network Setting 
> Network Setting (Windows) >
Specifying NetWare Protocols
iPF81510
790
 
						

							2.
In Print  Server  Name,  enter  the  name  of  the  print  server  created  in  " Specifying  NetWare  Print  Serv-
ices →P.787
."
3. In Print 

Server  Password,  enter  the  password  of  the  print  server  created  in  " Specifying  NetWare  Print
Services →P.787
."
4. In Polling Interval , specify the interval at which the printer checks the NetWare print queue.
• If you have selected NPrinter: Remote Printer Mode (Using a NDS Print Server)
1. In Print 

Server  Name ,  enter  the  advertising  name  of  the  print  server  created  in  " Specifying  NetWare
Print Services →P.787
." Usually, the advertising name is the same as the name of the print server.
2. In Printer 

Number ,  enter  the  same  printer  number  specified  in  " Specifying  NetWare  Print  Serv-
ices →P.787
."
11. Click OK to display the  Network page.
For a list of NetWare protocol settings items,  see "Configuring the Printer's NetWare Network Settings ." →P.784
Configuring NetWare Network Settings
To print over a NetWare network, configure the network environment as follows. Important
• To 
configure  network  settings,  you  must  be  logged  in  with  administrative  rights  such  as  Administrator  ac-
count. We recommend that your network administrator configure the network settings.
1. Specify the Ethernet frame type for communication between the printer and computers.
For instructions,  see "Specifying the Printer's Frame Type." →P.785
2. Specify the NetWare print services, including the print server and queue.
For instructions, see "Specifying NetWare Print Services ." →P.787
3. Specify NetWare protocol details besides the frame type.
For instructions, see "Specifying NetWare Protocols ." →P.789
After you have completed the steps above, configure each computer for printing over the NetWare network.
4. Connect to the NetWare network.
Install 

NetWare  client  software  on  each  computer  to  be  used  for  printing  over  the  network,  and  log  in  to  the  Net-
Ware server or tree. For instructions on connection, refer to the NetWare and operating system documentation.
5. Install the printer driver.
Follow  the  instructions  of  your  network  administrator  to  install  the  printer  driver  on  each  computer  to  be  used  for
printing. When installing the printer driver, choose  Network Printer as the printer destination, and then choose the
print queue created from the NetWare print service settings.
6. Follow  these  steps  to  configure  the  printer  port.  This  step  is  not  necessary  if  you  specified  the  printer  destination
during installation of the printer driver.
1. Open the Printers and Faxes (or Printers  ) window.
2. Right-click the printer icon and choose  Properties.
3. Click the  Port (or Advanced  ) tab to display the  Port (or Advanced  ) sheet.
Network Setting 
> Network Setting (Windows) >
iPF815
Configuring NetWare Network Settings 10
791
 
						

							4.
As the destination port, specify the print queue created by configuring the NetWare print service settings.
Network Setting > Network Setting (Windows) > Configuring NetWare Network Settings
iPF81510
792
 
						

							Network Setting (Mac OS X)
Configuring the Printer Driver Destination  ...................................................................................................... 793
 
Configuring the Printer's AppleTalk Network Settings ..................................................................................... 793
Configuring the Destination for AppleTalk Networks  ...................................................................................... 794
Configuring the Destination for TCP/IP Network  ............................................................................................ 797
Configuring the Destination for Bonjour Network  ........................................................................................... 800Configuring the Printer Driver Destination
Specify the printer driver destination as follows if the printer's IP address is changed, or if you will use the printer over a
network connection instead of via USB connection.
•If 
you  switch  to  printing  in  an  AppleTalk  network,  see  "Configuring  the  Destination  for  AppleTalk  Networks  ."→P.794
• If 

you switch to printing in a TCP/IP network, or if the printer's IP address is changed,  see "Configuring the Destina-
tion for TCP/IP Network ." →P.797
• If you switch to printing in a Bonjour network,  see "Configuring the Destination for Bonjour Network  ." →P.800
Configuring the Printer's AppleTalk Network Settings
Follow the steps below to configure the AppleTalk network settings.
1. Start 

the  web  browser  and  enter  the  following  URL  in  the  Location  (or Address  )  box  to  display  the  RemoteUI
page.
http://printer IP address or name/
Example: http://xxx.xxx.xxx.xxx/
2. Select Administrator Mode and click  Logon.
3. If a password has been set on the printer, enter the password.
4. Click Network in the  Device Manager menu at left to display the  Network page.
5. Click Edit in the upper-right corner of the  AppleTalk group to display the  Edit AppleTalk Protocol Settings  page.
6. Refer to the AppleTalk Settings Items table to complete the settings.
AppleTalk Settings Items Item
Details Default Setting
Phase
Type Specify whether to use AppleTalk.
If you will use AppleTalk, choose 
Phase 2.
If you will not use AppleTalk, choose  Disabled. Disabled
Name
(*1) Specify the object name used by AppleTalk (in up to 31 single-byte or 15 double-byte
characters).
However, do not use the following single-byte characters: @, *, :, and =. Canon
NB-17FB
(xxxxxx)
Zone (*2) Specify the printer zone name, up to 31 single-byte characters. *Network Setting 
> Network Setting (Mac OS X) >
iPF815
Configuring the Printer Driver Destination 10
793
 
						

							Item
Details Default Setting
Zone (*2) However, do not use the following single-byte characters: @, :, and =. Also avoid us- ing * (which represents the default zone) in the middle of a string. **1:The object name you have specified in 
Name is  displayed in Printer Setup Utility  (or Print Center  ) in Mac OS
X  10.2.8–10.4.  If  you  use  multiple  printers  in  the  same  zone,  assign  a  unique  name  to  each  printer.  By  default,
the  network  interface  name  is  Canon  NB-17FB  (xxxxxx).  (Here,  xxxxxx  is  the  last  six  digits  of  the  printer's
MAC address.)
*2:  If  zones  have  been  created  on  the  network,  enter  the  name  of  the  printer's  zone.  If  there  are  no  zones,  leave  the asterisk  *  entry  (for  the  default  zone)  as  it  is.  If  you  enter  a  network  zone  name  that  does  not  match  created
zones, the printer will not be detected by Macintosh computers. Consult your network administrator for informa-
tion on zone names.
7. Click OK  to display the Network page. Configuring the Destination for AppleTalk Networks
To print over an AppleTalk network, activate the AppleTalk protocol and configure the destination as follows. Activating AppleTalk on the printer
Important
• By factory default, the AppleTalk protocol is disabled on the printer.
1. Press the Menu button to display  MAIN MENU.2.
Press â–² or â–¼  to select Interface
  Setup, and then press the  â–¶ button.
3. Press  â–² or â–¼ to select  AppleTalk, and then press the  â–¶ button.
4. Press  â–² or â–¼ to select  On, and then press the OK  button.
Network Setting 
> Network Setting (Mac OS X) >
Configuring the Destination for AppleTalk Networks
iPF81510
794