Epson Aculaser CX28DN User Manual

							Replacing Consumables 189
2Open the machine’s front cover.
3Pull the front lever of the color 
toner cartridge indicated to the 
right.
The replacement procedure for 
the imaging unit is the same for 
all colors (yellow: Y, magenta: M, 
cyan: C, and black: K).
The following instructions show 
the procedure to replace the 
toner cartridge (K).
4Lower the lever to release the 
lock.
K
YMCK
K
K
 
						

							Replacing Consumables 190
5Press down the area marked 
“Push” on the imaging unit to be 
replaced, and then slide the unit 
all the way out of the machine. 
The following instructions show 
the procedure to replace the 
imaging unit (K).
Note
Dispose of the used imaging unit according to your local regulations.
Do not burn the imaging unit.
6Check the color of the new imaging unit to be installed.
In order to prevent toner from spilling, leave the imaging unit in the 
bag until step 5 is being performed.
7Remove the imaging unit from 
the bag.
K
K
KPUSH
 
						

							Replacing Consumables 191
8Hold the imaging unit with both 
hands, and then shake it twice 
as shown in the illustration.
Do not grab the bottom of 
the bag; otherwise, the 
imaging unit may be 
damaged, resulting in 
decreased print quality.
9Remove all packing tape from 
the imaging unit.
10Remove the protective cover 
from the imaging unit. The pro-
tective cover slides after having 
turned.
YPU
SH
YP
U
S
H
K
PUSH
P
U
S
H
K
 
						

							Replacing Consumables 192
11Make sure that the new imaging 
unit to be installed is the same 
color as the machine compart-
ment, and then install the imag-
ing unit in the machine.
12Raise the front lever to its origi-
nal position.
13Pull the lever to the left to lock it 
in place.
The front lever should be 
securely returned to its 
original position; other-
wise, the front cover of 
the machine cannot be 
closed.
K
K
K
K
 
						

							Replacing Consumables 193
14Close the front cover.
 
						

							Replacing Consumables 194
Replacing the Waste Toner Bottle
When the waste toner bottle becomes full, the message WASTE TONER 
FULL/REPLACE BOTTLE 
appears in the message window. The machine 
stops and will not start again until the waste toner bottle is replaced.
When replacing an waste toner bottle, refer to the following table. For opti-
mum print quality and performance, use only approved Epson waste toner 
bottle, as listed in the table below.
1Open the machine’s front cover.
Item Part number
Waste Toner Bottle S050498
 
						

							Replacing Consumables 195
2Turn the dial on the waste toner 
bottle counterclockwise until it is 
in the unlock position.
3Open the left and right handles 
of the waste toner bottle.
Lock Unlock
 
						

							Replacing Consumables 196
4Grab the left and right handles of 
the waste toner bottle, and then 
slowly pull out the bottle.
Be careful since some 
waste toner may spill if 
the lock is closed when 
the waste toner bottle is 
removed.
5Remove the new waste toner bottle from its packaging. Insert the used 
waste toner bottle into the plastic bag included in the box, and then box it 
up.
Note
Dispose of the used waste toner bottle according to your local 
regulations. Do not burn the waste toner bottle.
Before installing the waste toner bottle, be sure that the dial on the 
waste toner bottle is unlocked.
6Slide the waste toner bottle all 
the way into the machine.
 
						

							Replacing Consumables 197
7Turn the dial clockwise until the 
waste toner bottle is in the 
locked position. 
8Close the front cover.
If the waste toner bottle is not fully inserted or if the dial is not 
locked, the front cover cannot be closed.
Lock Unlock
 
						

							Replacing Consumables 198